Installation guide

ManualsBrandsSIIG ManualsAV extendersCE-H21J11-S1

Introduction

The Long Range HDMI Extender over Single Cat 5/6 with IR/

RS-232, and Ethernet provides an easy extension of HDMI

signal over one Cat5/6 cable up to 330ft and also provides

bi-directional RS-232, IR and Ethernet extension function.

Features and Benefits

• Unaltered, uncompressed HDMI signal over Cat5/

6 cable transmission

• Supports HDMI Deep Color, full 3D, Full HD 1080p

& 4Kx2K

• Extends data transmission up to 330ft (100m) at Full

HD 1080p

• Integrated Ethernet port for network capability

• Full Duplex RS-232 control up to 115,200 bps through

connector

• Supports Bi-Directional IR pass-through

• Metal housing with wall mount mechanism

04-0872A

Long Range HDMI Extender

over Single Cat5/6 with

IR/RS-232, and Ethernet

Quick Installation Guide

Summary of content (12 pages)

PAGE 1
Long Range HDMI Extender over Single Cat5/6 with IR/RS-232, and Ethernet Quick Installation Guide Introduction The Long Range HDMI Extender over Single Cat 5/6 with IR/ RS-232, and Ethernet provides an easy extension of HDMI signal over one Cat5/6 cable up to 330ft and also provides bi-directional RS-232, IR and Ethernet extension function.
PAGE 2
Package Contents • • • • • Long Range HDMI Extender over Single Cat5/6 with IR/ RS-232, and Ethernet (Transmitterx1, Receiverx1) Power adapter 24V/1A (2) IR blaster cable & IR receiver cable Screw kit Quick installation guide Layout Power LED Power jack IR blaster Ethernet IR receiver HDMI IN Figure 1: Transmitter_Rear IR blaster Power jack Power LED IR receiver HDMI OUT Ethernet Figure 2: Receiver _Rear • 2 HDMI IN: HDMI signal input port.
PAGE 3
• • • • HDMI OUT: HDMI signal output port.
PAGE 4
IR Extension Cables IR Blaster cable: Connect the IR blaster cable to your HDMI Extender's IR Blaster connector to send out IR command signals, if needed 1. IR Signal 2. Grounding 1 2 Figure 4 IR Receiver cable: Connect the IR receiver cable to your HDMI Extender's IR Receiver connector to receive IR command signals, if needed 1. IR Signal 2. Grounding 3.
PAGE 5
DIP Switch Refer to Figure 6 and Table 1 for the instructions for changing RS-232 mode by using DIP switch. Switch 1 Switch 2 Figure 6 • Firmware update mode: Push down DIP switch 2 to change to firmware update mode. Connect the RS232 connector on HDMI Extender to your computer for further firmware update. Note: Download firmware updates, as they become available, at www.siig.com. • RS-232 operation mode: Push up DIP switch 2 for RS-232 operation mode.
PAGE 6
NOTE: When the Transmitter is in DTE mode, Pin-2 of the RS-232 is in charge of sending data; when in DCE mode, Pin-3 is in charge of sending data. When Receiver is in DTE mode, the Pin-3 of the RS-232 is in charge of receiving data; when in DCE mode, the Pin-2 is in charge of receiving data.
PAGE 7
Hardware Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. Power off all devices, including the source HDMI device and display. Connect your HDMI source (such as a Blu-ray player) to the transmitter's HDMI IN connector. Connect your HDMI display (such as a LCD TV) to the receiver's HDMI OUT connector. Connect your RS-232 ports on the Transmitter and Receiver to the serial port devices separately if you want to extend serial signal transmission. P l e a s e adjust the DIP switch to the right position.
PAGE 8
Application Basic connection HDMI signal extended over Cat5/6 cable A : HDMI OUT B : HDBASET HDMI output display C : HDMI IN External power source HDMI cable A Receiver B Cat5/6 cable External power source B Transmitter C HDMI cable HDMI input source device (DVD, PC, etc) Figure 8 8
PAGE 9
Optional connections Bi-directional IR connection A : HDMI OUT B : HDBASET C : HDMI IN D : IR Blaster & Receiver on Transmitter E : IR Blaster & Receiver on Receiver HDMI output display HDMI cable External power source A E Receiver B Cat5/6 cable External power source B Transmitter D C HDMI cable HDMI input source device (DVD, PC, etc) * Connect IR blaster cable to D and IR Receiver cable to E to control HDMI display from Transmitter's side.
PAGE 10
Bi-directional RS-232 connections External power source Receiver A : RS-232 B : HDBASET A B RS-232 Controllable Device RS-232 cable Cat5/6 cable RS-232 cable A B RS-232 Control System External power source Transmitter Figure 10 Bi-directional Ethernet connections PC, Network router, network switch, etc A : Ethernet B : HDBASET Ethernet cable External power source A Receiver B Cat5/6 cable Transmitter External power source B Ethernet enabled device A Ethernet cable Figure 11 10
PAGE 11
Technical Support and Warranty QUESTIONS? SIIG’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst will promptly respond. SIIG offers a 3-year manufacturer warranty with this product.
PAGE 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio.