Specifications

ManualsBrandsSignify Investment ManualsElectronicsDigital Device

Signify Classified - Internal#

Hue Connect

Specification item Value Unit Condition

Description

The Hue Connect is a motherboard that accommodates

the Hue Engine. Its application is intended to be

used for color tunable luminaires. In combination

with the a 24V DC power supply and defined L1.5 LED

kit, color consistency can between luminaires or

light points within a luminaire can be guaranteed.

Logistical data

12NC 929002469604; 929002469605

Minimum Order Quantity 1024 PCE

Features & Functions

Electrical input data

Input power 70W

Current of single channel 2.9A Ampere

Electrical output data 67W Watt

Voltage 24V Volt +/-1V

Average power consumption

Standby power <120mW Watt

Wireless specifications

Wireless RF mode frequency band 2400–2483.5 MHz MHz

Wireless communications protocol

IEEE 802.15.4

Bluetooth LE

ZigBee protocol

Bluetooth LE

protocol

Operating channel 11 – 26 channels

Range 12 meter

indoor

Frequency tolerances (Typical) +/-40 ppm

Continuous single tone

Output power (Typical) 9 dBM

Measured at antenna feedpoint

EVM (Typical) 18 %rms

Receiver Sensitivity (Typical) -102 dBM

conducted

TRP 6 dBM

LED board requirements

Hue White Color Ambience Unified Gamut

covered by L1.5 specifications

Tunable white CCT range: 2000-6500K

covered by L1.5 specifications

Hue White Ambiance Tunable white CCT range: 2000-6500K

covered by L1.5 specifications

Hue White

2700K / 3000K / 4000K

covered by L1.5 specifications

Wiring & Connections

J1 connector Output to Sensor or 2nd light source

As interrupt for I2C, for button control 1 GPIO2

Mapped to ENABLE 2 GPIO3

I2C 3 Mix out2

Summary of content (5 pages)

PAGE 1
Signify Classified - Internal # Hue Connect Specification item Value Unit Condition The Hue Connect is a motherboard that accommodates the Hue Engine. Its application is intended to be used for color tunable luminaires. In combination with the a 24V DC power supply and defined L1.5 LED kit, color consistency can between luminaires or light points within a luminaire can be guaranteed.
PAGE 2
Signify Classified - Internal # 3.3V DC, supply for functions connected to I/O interface I2C Electrical Ground As interrupt for I2C, for button control 24V DC, 1.
PAGE 3
Signify Classified - Internal FCC # FCC Labelling Requirements When integrating HUE Connect into a product it must be ensured that the FCC labelling requirements are met. This includes a clearly visible label on the outside of the finished product specifying the FCC identifier (FCC ID:2AGBW9290024696X). This exterior label can use wording such as “Contains Transmitter Module FCC ID: 2AGBW9290024696X” although any similar wording that expresses the same meaning may be used.
PAGE 4
Signify Classified - Internal # IC (ISED Canada) Approvals This device complies with ISED Canadalicense-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 5
Signify Classified - Internal # Les exigences d’étiquetage pour Industrie Canada sont semblables à celles de la FCC. Encore une fois un clairement visiblement étiquette doit être placée à l’extérieur du produit fini indiquant quelque chose comme "Module émetteur de Contains, IC ID: 20812-24696X", bien que tout même libellé qui exprime que le même sens peuvent être utilisé.