Models: SMH200-17 SMH200-13 SMH200-10
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com TABLE OF CONTENTS About The Booster Kits ......................................................................... 3 Booster Kit Components ...................................................................... 5 Tools Required / Optional Equipment ................................................ 6 How It Works ..........................................................................................
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com NOTE: This manual contains important safety and operating information. Please read and follow the instructions in this manual, failure to do so could be hazardous and result in damage to your cellular booster.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com ! SAFETY AND WARNINGS • Turn AC power OFF at the mains before working on any electrical connections. • All AC power wiring and coaxial cable wiring must conform to local or national codes. The AC line voltage must be within 10% of the voltage specified for the booster. A solid copper conductor no less than No. 8 AWG should be connected to ground. • • • DO NOT connect a ground wire to a gas supply line.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com Electrical Specification Uplink Downlink Frequenecy Range Band 12 698~ 716 MHz 728 ~746 MHz Band 14 788~ 798MHz 758 ~768 MHz Max. Gain SMH200 50dB 53dB Max. Output Power SMH200 22dBm 18dBm Band Width Wide Band Automatic Level Control 15dB Manual Gain Control ≥31dB / 1dB step Spurious Emission ≤ -13dBm 9KHz~1GHz 1GHz~12.75GHz ≤ -13dBm Gain Flatness ≤8dB Noise Figure ≤8dB VSWR ≤3 Group Delay ≤ 1.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com OVERVIEW This guide will help you properly install your cellular booster kit. It is important to read through all of the installation steps before installing your equipment. Thoroughly read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com GETTING STARTED Plan the layout of your system Before you get started you will need to plan the layout of your system. This involves checking signal strength for signals coming from the cellular tower, as well as antenna, booster and cable placement.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com 1 2 3 4 5 6 7 BOOSTER – select location Install the booster in an area that is protected from the weather, properly ventilated and is away from excessive heat and moisture. SIGNAL ANTENNA (outdoor) - select location Mount the signal (outdoor) antenna in an elevated outdoor location so that it points towards the cellular tower and away from where the inside antenna will be located.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com IDENTIFY THE BEST LOCATION TO INSTALL THE SIGNAL (OUTDOOR) ANTENNA. Check for signal strength Select a location on the roof of the building to install the signal antenna, by monitoring your cellular phone’s signal strength (signal bars) to find the strongest signal from your carrier’s cellular tower. Mark the area Mark that area as the installation location for the signal (outdoor).
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com RUN COAXIAL CABLE Loosely run the coaxial cable from your outdoor antenna to your booster. (after you have tested the system you can permanently secure the coaxial cable). As you route and pull cabling, follow these general guidelines: • Bend cables and route them smoothly, and protect the outer skin against any damage. • Keep horizontal cables straight and fasten them with a tie every three to five feet.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com HOW TO INSTALL THE COAXIAL CABLE FROM YOUR OUTDOOR ANTENNA TO YOUR BOOSTER. Step 1: Loosely run the coaxial cable from your outdoor antenna to your booster (this way you can test the system before you permanently secure the coaxial cable). Outdoor Antenna Booster Step 2: Mount the signal (the outdoor antenna).
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com Step 3: After the outdoor antenna is mounted connect the supplied coaxial cable to antenna. Step 4: Attach the cable so that a drip loop is formed. Drip Loop Step 5: Connect the cable to the cellular booster where it is marked “outdoor”. outdoor cable booster CAUTION: please ensure neither you nor the antenna come in contact with electrical power lines.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com UNDERSTAND THE DIFFERENT SIGNAL (OUTDOOR) ANTENNA Signal (outdoor) antennas, are needed to capture the signal emanating from your carrier’s cellular tower. There are different types of signal (outdoor) antennas each designed to meet your specific needs. The yagi lpda antenna, the post antenna & the panel antenna. The Yagi Lpda Antenna The yagi is a very precise directional antenna with a powerful reach.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com LIGHTNING SURGE PROTECTOR (sold separately) The lightning surge protector can be installed indoors or outdoors. When connecting outdoors, install the lightning surge protector inline between the signal antenna (outdoor) and the coaxial cable. When connecting indoors, install the lightning surge protector inline between the outdoor coaxial cable and the booster. ! IMPORTANT: Lightning surge protector must be grounded.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com CONNECTING THE DISTRIBUTION (INDOOR) ANTENNA Dome omni directional antenna Connect one end of the coaxial cable to the dome antenna and the other end to the cellular booster where it is marked “indoor”. Indoor Booster Indoor Dome Antenna Panel directional antenna Connect one end of the coaxial cable to the panel antenna and the other end to the connector on the cellular booster where it is marked “indoor”.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com THE DOME ANTENNA The dome antenna is an omni-directional antenna with a 360 degree reach. It is designed to distribute the signal from the center of the affected area. Typically it is installed in a false or dropped ceiling. THE PANEL ANTENNA The panel is a directional antenna with a 120 degree reach and is designed to distribute the signal from a perimeter wall or ceiling.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com NOTE: installing additional distribution (indoor) antennas may be necessary when the area that needs coverage is very large or has barriers that block cellular signals such as multi level homes and buildings. The following diagrams show the reach of each antenna based on the layout of the space they are mounted in: Image 1&2: Omni directional antennas will provide better coverage for square rooms.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com ANTENNA SEPARATION Oscillation is caused when the indoor (distrubution) antenna sends a signal back into the outdoor (signal) antenna. Similar to a PA system, when the microphone gets too close to the speaker it causes feedback. This will occur if your antennas are too close together, or the indoor antenna is pointed at the outdoor antenna.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com INSTALL YOUR CELLULAR BOOSTER Install the cellular booster in a location that is properly ventilated and not exposed to excessive heat, moisture and/or direct sunlight. The optimal area would be on a wall located near a power outlet. It should be mounted in an easily accessible area so it’s easy to perform general maintenance with the coaxial cable connections, dip switch settings and power adaptor.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com ! IMPORTANT: Do not connect your cellular device to the cellular booster, as it may damage your cellular device. IMPORTANT: 1 2 3 Never point the front of the yagi signal (outdoor) antenna towards the inside of the distribution (indoor) antenna.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com CHECK THE BOOSTER LED ALARM LIGHTS Your cellular booster comes equipped with electronic sensors designed to identify cellular signal overload or oscillation which can hinder signal- boosting performance. Your cellular booster is specially designed to automatically decrease gain to compensate for these circumstances. The device also has a feature to automatically shut down in case of excessive oscillation.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com FCC RF Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in fixed exposure condition without restriction with minimum distance 20cm between the radiator and your body. FCC Warning Part 90 and Part 20 Signal Boosters . .This is a 90.219 Class B device. WARNING. This is NOT a CONSUMER device. It is designed for an installation by FCC LICENSEES and QUALIFIED INSTALLERS.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com TROUBLESHOOTING The LED alarm lights represent the status of the booster on each frequency. When the lights are green the device is operating normally meaning that it is not experiencing any oscillation (feedback) and it is boosting the signal at maximum power. When the LED lights begin to change color from green to orange to red, it means that particular frequency is experiencing some oscillation (feedback).
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com By capturing the best input signal you will be able to enjoy the maximum coverage and best quality signal inside where your distribution antennas are located. The better the input signal, the better the output signal. In order to find the best input signal, you want to place your outdoor (signal) antenna as high as possible with the least amount of obstruction between the antenna and the cellular base tower.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com FREQUENTLY ASKED QUESTIONS WHY ARE THE LED LIGHTS TURNING ORANGE, RED OR SHUTTING OFF? There are certain cases where your system could be experiencing oscillation. This can be attributed to either the quality of your input signal or having your signal (outdoor) antenna and distribution (indoor) antenna too close together. Please review the following guidelines to help resolve this issue: 1.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com I INSTALLED THE BOOSTER AND MY SIGNAL STRENGTH IS STILL WEAK In order to correct a weak signal; essentially you have the options of: • • • Adjust the aim of the signal (outdoor) antenna or replace it with a higher gain antenna. Move the distribution (indoor) antenna. Increase the number of distribution (indoor) antennas.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com MY LED’S ARE ALL GREEN BUT MY SIGNAL IS STILL WEAK - MY COVERAGE IS POOR If you receive a signal where you did not previously... or, if the radius of the service area covered is small...and your LED’s are all green... the booster is working properly but for some reason the signal is not very strong. This can be due to weak input signal.
9.5dBi Beautification Yagi Antenna Electrical Specifications Model NO. Frequency Range (MHz) Polarization Gain (dBi) Half Power Beam width Front-to-back ratio V.S.W.R SYN-BY-9D 698-960/1710-2700 Vertical 9.5 Hor: 60º/55º Ver: 90º/75º ≥ 18dB ≤1.5 Impedance (Ω) 50 Power Handling (W) 50 Connector Type Product Size (mm) Weight (KG) Reflector Material Operating temperature (℃) N-Type or Customized 300×210 ×65 1.
Outdoor Panel Antenna Electrical Specifications Model NO. SYN-OPA-8D Frequency Range (MHz) 698-960 Polarization Gain (dBi) Half-power beam width (º) Vertical 7 Hor: 78±10/70±10 Ver: 70±10 /65±10 Front-to-back ratio (dB) >12 V.S.W.R ≤1.5 Impedance (Ω) 50 Power Handling (W) 50 Connector Type Product Size (mm) Weight (KG) Rated wind velocity (m/s) Material Operating temperature (℃) N-Type or Customized 210*180*45 0.
Indoor Panel Antenna Electrical Specifications Model NO. SYN-IPA-8D Frequency Range (MHz) 698-960 Polarization Gain (dBi) Half-power beam width (º) Vertical 7 Hor: 65/60 Ver: 55/45 Front-to-back ratio (dB) ≥15 V.S.W.R ≤1.5 Impedance (Ω) 50 Power Handling (W) 50 Connector Type Product Size (mm) Weight (KG) Material Operating temperature (℃) N-Type or Customized 210*180*45 0.
Indoor Ceiling Antenna Electrical Specifications Model NO. SYN-CA-3D Frequency Range (MHz) 698--960 Polarization Gain (dBi) Beam width (º) V.S.W.R Impedance (Ω) Power Handling (W) Connector Type Product Size (mm) Weight (g) Material Operating temperature (℃) Vertical 3 Hor: 360 Ver: 90 ≤1.
5D-FB Coaxial cable Specifications Model NO. 5D-FB Frequency Range ( MHz) Rated capacitance Velocity Delay Maximum Pull Tension Minimum bending radius 1~6GHz 81.5±2 pf/m 81% 3.75ns/m 42 Ibs 91mm 400M 7.6 at typical 698~900M 15.0 frequencies: 1800M 26.3 2500M 33.0 Attenuation (dB/m) VSWR 50~3000MHz Inner conductor Dielectric ≤1.
Contact Tech Support at 1.800.215.7015 or email at support@signifimobile.com INSTRUCTION MANUAL Phone: 1-800-215-7015 Email: support@signifimobile.