Owners Manual

ManualsBrandsSignature Hardware ManualsPlumbing34-1/2" Sebastian Floor Mounted Tub Filler Faucet with Shut Off Valves - Includes Hand Shower, Valve Included

IMPORTANT FAUCET INSTALLATION NOTICE

Before using a newly installed faucet, remove the aerator, if applicable. Turn on the water to the faucet and

let it flow for 15 seconds. This flushes out sediment in the water line, preventing it from becoming lodged in

the faucet valves, which can affect performance and cause damage to the faucet.

5. Turn on the hot and cold faucet taps to release any

pressure and excess water. Turn off.

6. With a wrench, remove water lines underneath the

faucet, placing the ends in a bucket.

7. Open the shut-off valve or water main and let water

flow into the bucket for 15 seconds.

8. Close the shut-off valve or main supply, then reattach

the water lines to the faucet.

9. Reopen the valves to restore water to the faucet and

check for leaks.

FLUSHING WATER LINES

1. Place a towel at the base of the faucet and remove the

faucet aerator. If using pliers, place a rag around the

aerator to protect the finish.

2. Turn on the cold and hot water, letting the faucet run

for 10-15 seconds.

3. Rinse out the aerator, carefully noting the placement of

washers inside. Replace the aerator and check water

flow. If there is no improvement, continue to Step 4.

4. Close the shut-off valves or turn off your home's water

main, twisting the valves clockwise as far as possible.

If your faucet has an uneven flow or is dripping, it may be due to a buildup of sediment. Follow these steps

to restore normal water flow. If your faucet does not have an aerator, proceed to step 4.

What You'll Need: Open-ended wrench, large bucket, pliers, towel, rag.

Summary of content (4 pages)

PAGE 1
IMPORTANT FAUCET INSTALLATION NOTICE Before using a newly installed faucet, remove the aerator, if applicable. Turn on the water to the faucet and let it flow for 15 seconds. This flushes out sediment in the water line, preventing it from becoming lodged in the faucet valves, which can affect performance and cause damage to the faucet. FLUSHING WATER LINES If your faucet has an uneven flow or is dripping, it may be due to a buildup of sediment. Follow these steps to restore normal water flow.
PAGE 2
FLUSHING WATER LINES (CONTINUED) 5. Turn on the hot and cold faucet taps to release any pressure and excess water. Turn off. 6. With a wrench, remove water lines underneath the faucet, placing the ends in a bucket. 7. Open the shut-off valve or water main and let water flow into the bucket for 15 seconds. 8. Close the shut-off valve or main supply, then reattach the water lines to the faucet. 9. Reopen the valves to restore water to the faucet and check for leaks.
PAGE 3
CLEANING A FAUCET CARTRIDGE What You'll Need: Open-ended wrench, screw driver, small cup or other plastic container, towel. Note: If there is not a shut-off valve at the faucet, you will need an assistant at the water main. 1. Close the shut-off valves or turn off your home's water main. 2. Turn on the faucet's hot and cold taps to release excess water and pressure on the fixture. Turn off once excess water is expelled. 3.
PAGE 4
CLEANING A FAUCET CARTRIDGE (CONTINUED) 7. Place the cartridge(s) individually in a bucket of clean water and move each cartridge back and forth while cycling the stem through the operational settings. The handle may need to be temporarily placed on the stem to do this. 8. Reinsert the cartridge(s) in the correct position, then reassemble the trim and handle. Turn on the faucet to test water flow and check for leaks.