Installation Sheet

ManualsBrandsSignature Hardware ManualsBathroom FaucetsShannon Widespread Bathroom Faucet with Metal Cross Handles and Pop-Up Drain Assembly

1Shannon Widespread Faucet Installation Instructions

INSTALLATION

1. Ensure that the water supply below your sink is

completely shut oﬀ by turning the valve all the way to

the right.

Tip: Place a small bucket below your workspace to

catch any water that may drip during the installation

process.

2. Remove the T-connector, lock nut, and metal

washer from the spout’s threaded shank.

SHANNON WIDESPREAD FAUCET

GETTING STARTED

TOOLS AND MATERIALS:

BEFORE YOU BEGIN

We recommend consulting a professional if

you are unfamiliar with installing plumbing

ﬁxtures. Signature Hardware accepts no

liability for any damage to the faucet,

plumbing, sink, counter top, or personal

injury during installation.

Observe all local plumbing and building

codes.

Unpack and inspect the item for damage.

If any damage is found, contact our

Customer Relations team at

1-866-855-2284.

*not included

Ensure that you have gathered all of the

required materials that are needed for

the installation.

For these instructions, it is assumed that

the old faucet has been completely

removed and any necessary repairs or

modiﬁcations to the water supply have

been completed.

Plumber’s Tape

Basin Wrench

Thread Sealant*

Adjustable

Wrench*

Phillips Screwdriver

Small Bucket

OFF

900900, 918816, 918817, 918818,

918819

SKU(s):

Summary of content (7 pages)

PAGE 1
SKU(s): 900900, 918816, 918817, 918818, 918819 SHANNON WIDESPREAD FAUCET BEFORE YOU BEGIN INSTALLATION We recommend consulting a professional if you are unfamiliar with installing plumbing ﬁxtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or personal injury during installation. 1. Ensure that the water supply below your sink is completely shut oﬀ by turning the valve all the way to the right. Observe all local plumbing and building codes.
PAGE 2
SHANNON WIDESPREAD FAUCET 3. Set the decorative escutcheon over the center faucet hole, then set the spout into the hole. 4. From beneath the countertop, slide the metal washer back onto the threaded shank. Hand tighten the lock nut, then ﬁnish tightening using an adjustable wrench. Important: The opening on the metal washer should face the back of the faucet so that it will line up with the hole in the spout that is reserved for the drain’s lift rod. 5.
PAGE 3
SHANNON WIDESPREAD FAUCET 7. From beneath the counter top, insert the valve stem through the right-side faucet hole. From above the counter top, slide one of two decorative escutcheons onto the stem. Then, attach one of the two bell ﬂanges to the stem by hand tightening until secure. 8. From beneath the sink, position the stem so that the outlet on the side of the stem is pointing inward, towards the T-connector. While holding in place, hand tighten the lock nut. Finish tightening using a basin wrench. 9.
PAGE 4
SHANNON WIDESPREAD FAUCET 11. Attach the main water lines to the proper inlet on the bottom of each valve stem. Use an adjustable wrench to tighten, but be careful not to overtighten. Apply thread sealant or plumber’s tape to each threaded connection. Ensure that you are connecting the hot and cold lines appropriately. cold hot 12. To complete the installation, install the faucet handles using a Phillip’s screwdriver. 13.
PAGE 5
SHANNON WIDESPREAD FAUCET DRAIN INSTALLATION 1. Remove the ﬂange by unthreading it from the drain body. Remove the ﬂat rubber gasket as well. Lift Rod Stopper Stopper Tailpiece Drain Flange & Flat Rubber Gasket Thumb Screw 2. Set the ﬂat rubber gasket over the drain hole in your sink, then insert the ﬂange into the drain hole.
PAGE 6
SHANNON WIDESPREAD FAUCET 3. From beneath the sink, reattach the ﬂange by threading it back onto the drain body. 5. Position the drain so that the lever is facing the back of the ﬁxture, in line with the faucet’s lift rod. While holding in place, hand tighten the lock nut until secure then ﬁnish tightening with a basin wrench. Be careful not to overtighten, which can crack a fragile sink. Hand tighten lock nut 4. Connect the drain lever by threading it into the hole on the side of the drain body.
PAGE 7
SHANNON WIDESPREAD FAUCET 7. Use the link to attach the faucet’s lift rod to the drain lever. Pinch the metal clip located on the drain lever to remove. Slide one end of the clip back onto the lever, followed by the link, then the second end of the clip to secure. 9. Make any ﬁnal adjustments to the positioning of the link and drain lever as needed. Adjust until the drain fully opens and closes. OPEN CLOSED 8. Attach the lift rod to the top of the link and secure it by tightening the thumb screw. 10.