Notice: Signal Communications Limited reserves the right to make improvements to the product described in this manual at any time and without notice. This manual is copyrighted. All rights are reserved. This manual may not be copied, reproduced or translated in whole or part without prior consent from Signal Communications Limited. Third party trademarks are the property of their respective holders. Copyright (c) 1995-2000 Signal Communications Limited. All rights reserved. Version 2.
SECTION 1 INTRODUCTION Eyelet IIT is an advanced Video Monitoring System. The transmission unit is especially designed for monitoring medium sized firm, factory and warehouse. Four models are available to suit for different applications as follows, VT 3-4B: Transmitting B/W video frames. VT 3-4C: Transmitting color video frames. VT 3-4BA: Transmitting B/W video frames with 4 alarm inputs and 1 output switch supported.
SECTION _ INSTALLING 7e/eEye II] What You Need To install and operate the 7e/eEye III transmission unit, the following items are required: o Elevate lil Transmission Unit The image transmitter supports up to 4 video sources in all PAL or SCENT format. e CCD Camera Color / monochrome, PAL or SCENT. « Coaxial Cable (GR-59 recommended) It is used to connect the video output of the CCD camera to the video input of Eyeteeth IIT transmission unit.
System Connections Up to 4 alarms Up to 4 cameras Twa — RJ45 LAN cable 1BM Compatible Recommended Setup Procedures: Step 1: Step 2: Step 3: Step 4: Step 5: Plug one end of the RJ45 LAN cable into the socket marked Ethernet on the Eyelet [lI transmitter, then plug the other end to the Ethernet socket of the computer.
ER ER TEE ET TET TE TT Software Installation Before setting up please change the video setting to 800 x 600 true color or 16-bit high color in Win95/98’s Display Properties. Telling software CD contains an installation program, SEXTUPLET. Please use this program to setup the necessary files into the hard disk of the reception unit. Once you have completed the following installation procedure, you can run Winter directly from your hard disk.
Pin Definitions of the crossover RJ45 CABLE When linking eyeful III to PC, you need the crossover RJ45-to-RJ45 cable. Table F-2 lists the definitions for the crossover RJ45-to-RJ45 cable.
Functional Description n: HI CH4 Standard BNC connectors for the video sources. A composite video signal should be supplied to these connectors. ALARM & SW Connector This connector is used for connecting 1 remote control switches and 4 alarm inputs. All alarm channels have the same priority. Ethernet Socket The Ethernet socket is used for making connection to the Ethernet socket of PC. AUX and MODEM Connector These two connectors are used for future development. Power Socket A2.
SECTION 3 SPECIFICATIONS MODEL VT 3-4B VT 3-4C VT 3-4BA VT 3-4CA STANDARD (P): PARRICIDAL, 625 LINES, 50 FIELDS PER SECOND (N): NETSCAPE, 525 LINES, 60 FIELDS PER SECOND INTERFACE 4 CHANNELS, 1,0V,, COMPOSITE, BNC WITH 7502 TERMINATION FRAME CAPTURE RESOLUTION (H x V) 320 x 240 PIXELS GRAY LEVELS 256 COLORS | 16 MILLION | [16 MILLION SCALE ABLE ADAPTIVE IMAGE COMPRESSION INPUT 4 INDEPENDENT CHANNELS (NC/NO) OUTPUT 1 CHANNEL, DRY CONTACT CONTACT RATING: vac, 2A RESISTIVITY LOAD : 24Vdc, 2A INPUT VOLTAGE TYPE
1B-AFPR-B1 12189 F.82 7 FCC Statement on Class B WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment, NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.