User's Manual

ManualsBrandsSignal Communications ManualsElectronicsTeleEye RX Series

RX Series

Video Recording Transmitter

RX304

User Guide

Summary of content (164 pages)

PAGE 1
RX Series Video Recording Transmitter RX304 User Guide
PAGE 2
Notice: Signal Communications Limited reserves the right to make improvements to the product described in this manual at any time and without notice. This manual is copyrighted. All rights are reserved. This manual should not be copied, reproduced or translated in whole or part without prior consent from Signal Communications Limited. TeleEye is a trademark of Signal Communications Limited and is registered in China, European Communities, Hong Kong, US and other countries.
PAGE 3
FCC Statement on Class B WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
Declaration 1. EN 61000-4-2 Under the environment with the electrostatic discharge, the sample may malfunction and require user to reset the sample. 2. EN 61000-4-4 Under the environment with the electrical fast transient, the sample may malfunction and require user to reset the sample. 3.
PAGE 5
Table of Contents SECTION 1 INTRODUCTION A. Introduction B. Features C. Removing the Packages D. Convention Used in This Manual E. Front Panel Description F. Rear Panel Description 1 2 3 4 5 8 SECTION 2 HARD DISK INSTALLATION, FORMATTING AND SCANNING A. Hard Disk Installation B. Hard Disk Formatting C. Hard Disk Scanning D. Hard Disk Recommendation List 11 14 16 18 SECTION 3 BASIC INSTALLATION FOR LOCAL AND REMOTE MONITORING A. Setup TeleEye RX for Local CCTV Monitor B.
PAGE 6
SECTION 5 OSD MENU OPERATION A. Main Menu B. Recording Log Menu C. PTZ Menu D. Recording Menu E. Event Menu 73 87 89 91 92 SECTION 6 ADVANCE OPERATION A. Install TeleEye RX with Alarm Sensors and Relay Control Port B. Install TeleEye RX with Tamper Circuit and External Resistor C. Event Handling I. Arm/Disarm II. Security Switch III. Alarm IV. Motion V. Videoloss VI. System Tamper VII. Power Failure D. Event Action I. Recording II. Switch III. Dialback IV. Buzzer V. Event LED VI. Live Camera VII. PTZ E.
PAGE 7
Tele Eye RX User Guide Page 1 SECTION 1 INTRODUCTION A. Introduction TeleEye RX Series Video Recording Transmitter operates with its revolutionary multirate video coder to fulfill the highest video coding requirements for simultaneous transmission and recording.
PAGE 8
Tele Eye RX User Guide Page 2 B.
PAGE 9
Tele Eye RX User Guide Page 3 C. Removing the Packages After removing the package, make sure you have the following items: - TeleEye RX Video Recording Transmitter with Built-in CD Writer - Hard Disk Cartridge Accessories (Key x 2 and Screw x 4) - User Guide - Warranty Card - Registration Code Sheet - HDD Recommendation List - Software CD - Power Adaptor and Power Cord - Alarm Port Connector (37 Pins) & Alarm Port Cover - Resistors (1.
PAGE 10
Tele Eye RX User Guide Page 4 D.
PAGE 11
Tele Eye RX User Guide Page 5 E. Front Panel Description I. Removable Hard Disk - Built with a removable hard disk cartridge - {Key Lock} and {Key}are provided to lock the hard disk from unauthorized removing - {Key} can also be used to enable/disable the power supply to the system II. Live Camera Control Buttons - “1”, “2”, “3”, “4” - “Camera Control” buttons allow user to fast switch to a specific camera for local monitoring III.
PAGE 12
Tele Eye RX User Guide V.
PAGE 13
Tele Eye RX User Guide VI.
PAGE 14
Tele Eye RX User Guide Page 8 F. Rear Panel Description I. Video Input Connectors - Channel 1 – Channel 4 (for TeleEye RX304 only) - {Standard BNC connectors} for video source input - A composite video source from camera should be supplied to these connectors II. Video Output Connector - A composite video signal with 1V p-p is output from this connector - Support PAL or NTSC format - PAL/CCIR format with 625 lines, 50 fields per second - NTSC/EIA format with 525 lines, 60 fields per second III.
PAGE 15
Tele Eye RX User Guide IV. Page 9 Ethernet Socket (10/100 Base-T) - This socket is used for connecting TeleEye RX to the corporate computer network (e.g. LAN) - This socket includes {COL LED} and {LINK LED} - {COL LED} : When ON, indicates that collision is occurring on the network - {LINK LED} : When ON, indicates that TeleEye RX is connecting to the network and ready to function V. USB - VI.
PAGE 16
Tele Eye RX User Guide Page 10 VIII. Relay Out / Alarm In Port - 4 relay (also call switch) ports - 4 alarm ports - All alarm ports are NC/NO type and none/SEOL/DEOL tamper type input - All relay ports are latching/push-button type output IX. Power - Connect power supply (12V DC, 5A) to TeleEye RX transmitter X.
PAGE 17
Tele Eye RX User Guide Page 11 SECTION 2 Hard Disk Installation, Formatting and Scanning A. Hard Disk Installation TeleEye RX transmitter supports ATA standard hard disk. User should use the hard disk listed at the hard disk recommendation list on P.18. Recommendation : The hard disk is recommended to set to Master Mode. How to set to Master Mode, please refers to the hard disk case or its manual Hard Disk Front Panel Description 1. HDD Activity indicator 2. Power indicator 3. Active-handle 4.
PAGE 18
Tele Eye RX User Guide Page 12 Installation Procedure Turn OFF transmitter Step 1: Press “Menu” button, select [SHUT DOWN] option and press “Enter” button. Step 2: [SHUT DOWN] menu will pop up and select [SHUT DOWN] option and press “Enter” Step 3: Select [YES] option and press “Enter” button to turn off the transmitter. Switch OFF the transmitter when the [IT IS NOW SAFE TO TURN OFF RX] message pop up. button. Note that you MUST turn OFF the transmitter when install or remove Hard disk.
PAGE 19
Tele Eye RX User Guide Page 13 Step 7: Insert the DC power cable and IDE cable on the HDD Step 8: Position the HDD into carrier body and secure the HDD using the four screws provided. Step 9: Slide the top cover back to the carrier body by sliding forward to secure. Step 10: Slide the carrier body back into the cartridge frame and push carrier body further into cartridge frame until fully inserted.
PAGE 20
Tele Eye RX User Guide Page 14 B. Hard Disk Formatting Hard disk formatting will reconstruct the structure of hard disk so that it is readable by TeleEye RX transmitter. If you have your own hard disk to install to TeleEye RX transmitter, you must perform hard disk formatting. I. New Hard Disk Formatting It will be used if the hard disk format is NOT TeleEye RX transmitter recognized format.
PAGE 21
Tele Eye RX User Guide Page 15 II. Menu Formatting It will be used if user wants to format the hard disk so as to have a clean recording space and redeem the file allocation. Procedure MAIN MENU Step 1: Press “Menu” SETUP BACKUP TO CD-R SWITCH CONTROL SCAN / FORMAT DISK TRANSMITTER INFO SHUT DOWN ... ... ... ... ... ENTER button, select [SCAN/FORMAT DISK] option and press “Enter” button to enter [SCAN/FORAMAT DISK] sub menu.
PAGE 22
Tele Eye RX User Guide Page 16 C. Hard Disk Scanning It is a hard disk maintenance function similar to the Scan Disk function provided by the Operating System of your personal computer. TeleEye RX transmitter provides this function so as to rescue the hard disk when errors found, and to enhance its performance and reliability. After scanning, if there is any damaged file, it will be deleted so that the remaining normal videos can playback. It will be used in the following cases: 1.
PAGE 23
Tele Eye RX User Guide Page 17 Warning message board will pop up. SCAN DISK ALL RECORDING WILL STOP DURING SCANDISK SURE TO PROCEED ? YES NO Step 3: Select [YES] option and press “Enter” button to start the [SCANDISK] process. Step 4: [SCAN DISK] processing board will pop up SCAN DISK \ SCANNING 90% to show you about the status. After finishing scan disk, it will return to the [SCAN / FORMAT DISK] menu.
PAGE 24
Tele Eye RX User Guide Page 18 D. Hard Disk Recommendation List Harddisk Capacity 40GB Product Line Model No.
PAGE 25
Tele Eye RX User Guide Page 19 SECTION 3 Basic Installation for Local and Remote Monitoring A.
PAGE 26
Tele Eye RX User Guide Page 20 Setup Procedure Step 1: Connect cameras to TeleEye RX {Video Input} with RG59 cable and BNC connector. Note that the cameras system is either NTSC or PAL and suppose all cameras are used the SAME system forma.(For PTZ camera installation, please refer P.148 to Advance Operation Section of the User Guide). Step 2: Connect CCTV monitor to TeleEye RX {Video Output} with RG59 cable and BNC connector.
PAGE 27
Tele Eye RX User Guide Page 21 Step 6: Press the “Menu” button to pop up the MAIN MENU SETUP BACKUP TO CD-R SWITCH CONTROL SCAN / FORMAT DISK TRANSMITTER INFO SHUT DOWN ... ... ... ... ... ENTER [MAIN MENU] on OSD. Step 7: Use “Up” or “Down” button to select [SETUP] option and press “Enter” button to enter the [SETUP] sub-menu. SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ...
PAGE 28
Tele Eye RX User Guide Page 22 B.
PAGE 29
Tele Eye RX User Guide Page 23 Setup Procedure Step 1: Connect cameras to TeleEye RX {Video Input} with RG59 cable and BNC connector. Note that the cameras system is either NTSC or PAL and suppose all cameras are used the SAME system format.(For PTZ camera installation, please refer P.148 to Advance Operation Section of the User Guide). Step 2: Connect CCTV monitor to TeleEye RX {Video Output} with RG59 cable and BNC connector.
PAGE 30
Tele Eye RX User Guide Page 24 Step 6: Press the “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER button to pop up the [MAIN MENU] on OSD. Step 7: Use “Up” or “Down” button to select [SETUP] option and press “Enter” button to enter the [SETUP] sub-menu.
PAGE 31
Tele Eye RX User Guide Page 25 Step 11a: Configure TeleEye RX transmitter IP setting through CCTV Monitor TeleEye RX RG59 cable 192.168.0.2 RG59 cable CCTV Ethernet Power Adapter Cameras Monitor Press the “Menu” button such that the OSD Socket SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER main menu opens on the monitor.
PAGE 32
Tele Eye RX User Guide Page 26 IP Use “Left” or “Right” select field and use “Up” IP : 210. 17.139.145 button to or “Down” button to set number. Press “Enter” button to save the change and return previous menu. TCP / IP IP PORT SUBNET MASK ENABLE GATEWAY GATEWAY ENABLE DNS PRIMARY DNS SECONDARY DNS SURELINK Follow the network setting and assign a valid subnet mask to [SUBNET MASK] and select 210.17.139.145 1024 255.255.255.0 YES 210.17.139.1 NO 0.0.0.0 0.0.0.
PAGE 33
Tele Eye RX User Guide Page 27 Step 11b: Configure TeleEye RX transmitter IP setting through PC TeleEye RX 192.168.0.3 192.168.0.2 Ethernet Socket RG59 cable Cameras Power Adapter Cross-over Ethernet Cable In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties.
PAGE 34
Tele Eye RX User Guide Page 28 Enter an IP address, subnet mask and Default gateway. Note that IP address should be “192.168.0.xx” except “192.168.0.2” which is TeleEye RX default IP address. Enter the Preferred and Alternate DNS server, if necessary. Click OK to activate the new IP. You have to confirm that IP address has been correctly set on your computer.
PAGE 35
Tele Eye RX User Guide Page 29 Choose [Transmitter] [Registration] to register the TeleEye RX transmitter. User needs to input transmitter serial number and registration code. For example : Serial No. : VTC12345 Registration Code : 1234567890 Press [Connect] icon to pop up the [Connect Window]. Type and select the following setting : Phone/IP : 192.168.0.2 Connect Using: TCP/IP LAN Password: 000000 IP (192.168.0.
PAGE 36
Tele Eye RX User Guide Page 30 Settings] icon to configure network setting. Change the IP from 192.168.0.2 to 210.17.139.145 (for example). Gateway setting is used for WAN. Primary and Secondary DNS setting are used for sureLINK, time synchronization ** or email notification function **. ** : This function will be supported in the TeleEye RX transmitter version 2.00.00 or later Press [Apply] icon to save the network setting and pop up the message board.
PAGE 37
Tele Eye RX User Guide Page 31 In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties. Choose Internet Protocol (TCP/IP) and click Properties Enter the IP address, subnet mask and Default gateway for the PC to restore to its original network configuration. Note that the first 3 field of IP address should be same as TeleEye RX transmitter IP and gateway address. IP address is “210.17.139.
PAGE 38
Tele Eye RX User Guide Page 32 Step 14: Run WX-30 software at any local network PC. (For details of WX-30 software installation, please refer to WX-30 Software Guide) Step 15: Press [Connect] icon to pop up the [Connect Window]. For example, type and select the following setting : Phone/IP : 210.17.139.145 Connect Using: TCP/IP LAN Password: 000000 Step 16: Press [Connect] icon to connect your PC and the transmitter. The video appears on the WX-30 if success.
PAGE 39
Tele Eye RX User Guide Page 33 C.
PAGE 40
Tele Eye RX User Guide Page 34 Setup Procedure Step 1: Connect cameras to TeleEye RX {Video Input} with RG59 cable and BNC connector. Note that the cameras system is either NTSC or PAL and suppose all cameras are used the SAME system format. (For PTZ camera installation, please refer P.148 to Advance Operation Section of the User Guide). Step 2: Connect CCTV monitor to TeleEye RX {Video Output} with RG59 cable and BNC connector.
PAGE 41
Tele Eye RX User Guide Page 35 Step 6: Press the “Menu” button to pop up the MAIN MENU SETUP BACKUP TO CD-R SWITCH CONTROL SCAN / FORMAT DISK TRANSMITTER INFO SHUT DOWN ... ... ... ... ... ENTER [MAIN MENU] on OSD. Step 7: Use “Up” or “Down” button to select [SETUP] option and press “Enter” button to enter the [SETUP] sub-menu. SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ...
PAGE 42
Tele Eye RX User Guide Page 36 Step 11a: Configure TeleEye RX transmitter IP setting through CCTV Monitor TeleEye RX RG59 cable 192.168.0.2 Ethernet RG59 cable Socket CCTV Cameras Monitor Power Adapter SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER Press the “Menu” button such that the OSD main menu pops up on the monitor.
PAGE 43
Tele Eye RX User Guide Page 37 IP Use “Left” or “Right” to select field and use “Up” IP : 210. 17.139.145 button or “Down” button to set number. Press “Enter” button to save the change and return previous menu. TCP / IP IP PORT SUBNET MASK ENABLE GATEWAY GATEWAY ENABLE DNS PRIMARY DNS SECONDARY DNS SURELINK 210.17.139.145 1024 255.255.255.0 YES 210.17.139.1 NO 0.0.0.0 0.0.0.
PAGE 44
Tele Eye RX User Guide Page 38 Step 11b: Configure TeleEye RX transmitter IP setting through PC TeleEye RX 192.168.0.3 192.168.0.2 Ethernet RG59 cable Socket Cameras Power Adapter Cross-over Ethernet Cable In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties.
PAGE 45
Tele Eye RX User Guide Page 39 Enter an IP address, subnet mask and Default gateway. Note that IP address should be “192.168.0.xx” except “192.168.0.2” which is TeleEye RX default IP address. Enter the Preferred and Alternate DNS server, if necessary. Click OK to activate the new IP. You have to confirm that IP address has been correctly set on your computer.
PAGE 46
Tele Eye RX User Guide Page 40 Choose [Transmitter] [Registration] to register the TeleEye RX transmitter. User needs to input transmitter serial number and registration code. For example : Serial No. : VTC12345 Registration Code : 1234567890 Press [Connect] icon to pop up the [Connect Window]. Type and select the following setting : Broadband Connection : Phone/IP : 192.168.0.2 Connect Using: TCP/IP Broadband Password: 000000 OR Narrowband Connection : Phone/IP : 192.168.0.
PAGE 47
Tele Eye RX User Guide Page 41 Press [Transmitter setup] icon to show TeleEye RX configuration menu. Select [Connection] and press [Network Settings] icon to configure network setting. Change the IP from 192.168.0.2 to (for example) 210.17.139.145 and Gateway setting 210.17.139.1 (for example). Primary and Secondary DNS setting (for example) are used for sureLINK, time synchronization** or e-mail notification function **.
PAGE 48
Tele Eye RX User Guide Page 42 In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties. Choose Internet Protocol (TCP/IP) and click Properties Enter the IP address, subnet mask and Default gateway for the PC to restore to its original network configuration. Click OK to apply the setting Step 12: Disconnect the transmitter and current PC.
PAGE 49
Tele Eye RX User Guide Page 43 Step14: Configure the network setting for TeleEye RX transmitter and your PC if necessary, such as router/gateway port mapping (select router/gateway IP as IP provided by your ISP and the transmitter IP as IP provided by the router/gateway), firewall, etc. (Please refers to the manual of your router/gateway.) Step15: Run WX-30 software at any network PC.
PAGE 50
Tele Eye RX User Guide Page 44 D. Setup TeleEye RX for Broadband or Narrowband Internet Connection with Dynamic IP Connection Topology VIDEO OUT: Connect to monitor with RG59 cable and VIDEO IN: Connect to BNC connector cameras with RG59 cable and BNC connector RG59 cable TeleEye RX CCTV Monitor www.your_site.your_company.teleeye.
PAGE 51
Tele Eye RX User Guide Page 45 Setup Procedure Step 1: Connect cameras to TeleEye RX {Video Input} with RG59 cable and BNC connector. Note that the cameras system is either NTSC or PAL and suppose all cameras are used the SAME system format. (For PTZ camera installation, please refer P.148 to Advance Operation Section of the User Guide). Step 2: Connect CCTV monitor to TeleEye RX {Video Output} with RG59 cable and BNC connector.
PAGE 52
Tele Eye RX User Guide Page 46 Step 6: Press the “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER button to pop up the [MAIN MENU] on OSD. Step 7: Use “Up” or “Down” button to select [SETUP] option and press “Enter” button to enter the [SETUP] submenu.
PAGE 53
Tele Eye RX User Guide Page 47 Step 11a: Configure TeleEye RX transmitter IP setting through CCTV Monitor TeleEye RX RG59 cable 192.168.0.2 RG59 cable Ethernet Socket CCTV Cameras Monitor Power Adapter Press the “Menu” button such that the SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER OSD main menu pops up on the monitor. Use “Up” button.
PAGE 54
Tele Eye RX User Guide Page 48 IP Use “Left” or “Right” to select field and use “Up” IP : 210. 17.139. 5 button or “Down” button to set number. Set IP address (for example) to 210.17.139.5 Press “Enter” button to save the change and return previous menu. Follow the network setting and assign TCP / IP IP PORT SUBNET MASK ENABLE GATEWAY GATEWAY ENABLE DNS PRIMARY DNS SECONDARY DNS SURELINK valid subnet mask to [SUBNET MASK] 210.17.139.5 1024 255.255.255.0 YES 210.17.139.1 NO 0.0.0.0 0.0.
PAGE 55
Tele Eye RX User Guide Page 49 SURELINK ENABLED SURELINK ADDRESS REFRESH RATE Select [SURELINK] option from TCP/IP menu and press “Enter” YES www….. 1 MINS button to enter the sub menu. Select [ENABLED] option and press “Left” or “Right” button to set [YES] value Select [SURELINK ADDRESS] option button to and press “Enter” sureLINK editing menu.
PAGE 56
Tele Eye RX User Guide Page 50 Step 11b: Configure TeleEye RX transmitter IP setting through PC TeleEye RX 192.168.0.3 192.168.0.2 RG59 cable Ethernet Socket Cameras Power Adapter Cross-over Ethernet Cable In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties.
PAGE 57
Tele Eye RX User Guide Page 51 Enter an IP address, subnet mask and Default gateway. Note that IP address should be “192.168.0.xx” except “192.168.0.2” which is TeleEye RX default IP address. Enter the Preferred and Alternate DNS server, if necessary. Click OK to activate the new IP. You have to confirm that IP address has been correctly set on your computer.
PAGE 58
Tele Eye RX User Guide Page 52 Choose [Transmitter] [Registration] to register the TeleEye RX transmitter. User needs to input transmitter serial number and registration code. For example : Serial No. : VTC12345 Registration Code : 1234567890 Press [Connect] icon to pop up the [Connect Window]. Type and select the following setting : Broadband Connection : Phone/IP : 192.168.0.2 Connect Using: TCP/IP Broadband Password: 000000 OR Narrowband Connection : Phone/IP : 192.168.0.
PAGE 59
Tele Eye RX User Guide Page 53 Press [Transmitter Setup] icon to show TeleEye RX configuration menu. Select [Connection] and press [Network Settings] icon to configure network setting. For example : Assign 210.17.139.5 to IP Assign 210.17.139.1 to Gateway Assign 202.14.67.4 to Primary DNS Assign 202.14.67.14 to Secondary DNS Enable sureLINK Assign “www.your_site.your_company.teleeye.net” (please refer P.152 to sureLINK section to get the address) to text field.
PAGE 60
Tele Eye RX User Guide Page 54 In Windows 2000/XP desktop, select Start > Control Panel Double click Network and Dial-up Connections > right click Local Area Connections and choose Properties. Choose Internet Protocol (TCP/IP) and click Properties Enter the IP address, subnet mask and Default gateway for the PC to restore to its original network configuration. Click OK to apply the setting Step 12: Disconnect the transmitter and current PC.
PAGE 61
Tele Eye RX User Guide Page 55 Step14: Configure the network setting for TeleEye RX transmitter and your PC if necessary, such as router/gateway port mapping (select router/gateway IP as IP provided by your ISP and the transmitter IP as IP provided by the router/gateway), firewall, etc. (Please refers to the manual of your router/gateway.) Step15: Run WX-30 software at any network PC.
PAGE 62
Tele Eye RX User Guide Page 56 E.
PAGE 63
Tele Eye RX User Guide Page 57 Setup Procedure Step 1: Connect cameras to TeleEye RX {Video Input} with RG59 cable and BNC connector. Note that the cameras system is either NTSC or PAL and suppose all cameras are used the SAME system format. (For PTZ camera installation, please refer P.148 to Advance Operation Section of the User Guide). Step 2: Connect CCTV monitor to TeleEye RX {Video Output} with RG59 cable and BNC connector.
PAGE 64
Tele Eye RX User Guide Page 58 Step 6: Press the “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER button to pop up the [MAIN MENU] on OSD. Step 7: Use “Up” or “Down” button to select [SETUP] option and press “Enter” button to enter the [SETUP] submenu.
PAGE 65
Tele Eye RX User Guide Page 59 Step 11a: Configure TeleEye RX transmitter modem connection setting through CCTV Monitor TeleEye RX RG59 cable 192.168.0.2 RG59 cable CCTV Ethernet Power Adapter Monitor Cameras Socket SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER Press the “Menu” button such that the OSD [MAIN MENU] pop up on the monitor.
PAGE 66
Tele Eye RX User Guide Page 60 Step 11b: Configure TeleEye RX transmitter modem connection setting through PC RG59 cable TeleEye RX CCTV Monitor RG59 cable RS232 serial cable Cameras Power Adapter Telephone cable Telephone Modem RS232 serial cable Network Telephone cable Modem Modem Setup for Windows 2000/XP of PC In Windows 2000/XP desktop, select Start > Control Panel Double click Add Hardware, press Next, to search the modem connected to the PC automatically Windows 2000/XP ca
PAGE 67
Tele Eye RX User Guide Page 61 After searching the modem, Windows 2000/XP can install the modem driver automatically. Press [Finish] button to exit the menu. The modem is ready to use. Run WX-30 software which has been installed to the PC. (For details of WX-30 software installation, please refer to WX-30 Software Guide) Choose [Transmitter] [Registration] to register the TeleEye RX transmitter. User needs to input transmitter serial number and registration code.
PAGE 68
Tele Eye RX User Guide Page 62 Press [Connect] icon to pop up the [Connect Window]. For example, type and select the following setting : Phone/IP : 29955992 (Phone number of the transmitter) Connect Using : U.S. Robotics 56K Voice EXT PnP (Modem Driver) Password: 000000 Press [Connect] icon to connect your PC and the transmitter. The video appears on the WX-30 if success. Otherwise, the [Warning] board will pop up and show you failure message.
PAGE 69
Tele Eye RX User Guide Page 63 Assign modem baud rate in order to adjust modem connection speed. Assign ring count, so modem can connect to the transmitter after that ring count. Press [Apply] icon to save the network setting and pop up the message board. After several seconds, the transmitter will restart automatically.
PAGE 70
Tele Eye RX User Guide Page 64 After searching the modem, Windows 2000/XP can install the modem driver automatically. Press [Finish] button to exit the menu. The modem is ready to use. Run WX-30 software which has been installed to the PC. (For details of WX-30 software installation, please refer to WX-30 Software Guide) Press [Connect] icon to pop up the [Connect Window].
PAGE 71
Tele Eye RX User Guide Page 65 Press [Connect] icon to connect your PC and the transmitter. The video appears on the WX-30 if success. Otherwise, the [Warning] board will pop up and show you failure message. For failure case, please press [Connect] icon to check that the connection setting is valid or not.
PAGE 72
Tele Eye RX User Guide Page 66 SECTION 4 Basic Operation for Local and Remote Monitoring A. Local CCTV Monitor : Live Monitoring, Recording and Playback I. Live Monitoring Press “Screen Control” buttons to view the live video in full, quad and sequential display mode. FULL QUAD SEQUENTIAL Note that when PTZ camera has been enabled, then sequential live mode cannot be selected.
PAGE 73
Tele Eye RX User Guide II. Page 67 Recording Step 1: Press “Rec” START RECORDING START RECORDING RECORDING CAMERA ENTER 1234 button and [START RECORDING] menu will pop up. Step 2: Select [RECORDING CAMERA] button to option and press “Enter” enable recording cameras. RECORDING CAMERA 1-3- Step 3: Use “Left” or “Right” button to select the recording camera or “Down” and use “Up” (e.g. Cam 1 & 3 are enabled, Cam 2 & 4 are button to enable or disable the disabled) recording camera.
PAGE 74
Tele Eye RX User Guide Page 68 III. Playback RECORDING LOG TIME CAMERA 11 : 00 1234 12 : 00 ---4 13 : 00 ---14 : 00 -2-15 : 00 ---16 : 00 1--17 : 00 1--18 : 00 ---- EVENT --------------------------------- 12 – 13 AUG2005 REMARK SENSOR -------------- - - ------------------------------------------------------ Step 1: Press “Search” button to pop up [RECORDING LOG] board on OSD.
PAGE 75
Tele Eye RX User Guide Page 69 Step 5: Using “Playback Control button” for “play” , “pause” , “forward” , “fast forward” , “step forward” backward” , “rewind” , “step and “stop”. ( For detail, refer to page 5 Front Panel Section of User Guide) Step 6: Press “screen control” or “camera control” buttons to change the view mode in local CCTV video playback. Note that if user record video by using quad recording mode, the playback video may not be so good in full screen display mode.
PAGE 76
Tele Eye RX User Guide Page 70 B. TeleEye RX Reception Software WX-30 : Live Monitoring, Recording and Playback I. Live Monitoring User can view a particular camera by simply clicking the camera button (e.g. 1, 2 or 3) on the camera control panel, or view all cameras, click [All] icon. Screen views in Full screen Screen views in Quarter screen Screen views in Hex screen Auto-arrange can optimise the screen views in order to display as many high-resolution pictures as possible.
PAGE 77
Tele Eye RX User Guide II. Page 71 Recording Step 1: Press [Record] icon to setup recording setting. Step 2: Input administrator password (000000 as default password) and press [OK] button.
PAGE 78
Tele Eye RX User Guide Page 72 III. Playback Step 1: Press [Play] icon to show playback menu Step 2: Select and input the record date and time for searching and press [Reload] icon. Step 3: Select a time slot record and press [Start Playback] button. Step 4: Use “playback control button” to control playback video such as “play”, “pause”, “forward”, “backward” and “stop” function.
PAGE 79
Tele Eye RX User Guide Page 73 SECTION 5 OSD Menu Operation A. Main Menu MAIN MENU SETUP BACKUP TO CD-R SWITCH CONTROL SCAN / FORMAT DISK TRANSMITTER INFO SHUT DOWN 1. Press the “Menu” 2. Using the “Up” ... ... ... ... ... ENTER button to open the main menu / “Down” button to select a sub-menu 3. A selected sub-menu option will be pointed by a hand cursor and highlighted 4. Press “Enter” button to confirm the selection and open the sub-menu 5. If menu option ends with [. . .
PAGE 80
Tele Eye RX User Guide 8. Press “Live” Page 74 button or “Back” button until OSD disappear to exit menu and save the setting. [SETTING SAVED] message will be shown.
PAGE 81
Tele Eye RX User Guide Page 75 Main Menu Setup Video VIDEO CAMERA SETTING LOCAL MONITORING OSD COLOR VIDEO FORMAT ... ... BLUE PAL The video menu contains the following options : Change camera name and install camera : Change local CCTV monitor related setting : Change OSD color : Change the video format to PAL or NTSC format CAMERA SETTING LOCAL MONITORING OSD COLOR VIDEO FORMAT Main Menu Setup Video Camera Setting CAMERA SETTING CAMERA CAMERA CAMERA CAMERA 1 2 3 4 ... ... ... ...
PAGE 82
Tele Eye RX User Guide Page 76 Main Menu Setup Video Camera Setting Camera X Setting CAMERA X SETTING INSTALLED NAME SUPPORT PTZ GENERAL PTZ SETTING YES CAMERA X YES ...
PAGE 83
Tele Eye RX User Guide Page 77 Main Menu Setup Video Camera Setting Camera X Setting General PTZ Setting PTZ Movement Setting PTZ MOVEMENT SETTING PAN DURATION TILT DURATION ZOOM DURATION FOCUS DURATION IRIS DURATION ADDITIONAL DURATION WASHER DURATION WIPER DURATION PATROL SPEED DWELL TIME 5 5 3 3 3 3 3 3 3 2 The PTZ movement setting menu contains the following options : Select the PTZ camera pan duration : Select the PTZ camera tilt duration : Select the PTZ camera zoom duration : Selec
PAGE 84
Tele Eye RX User Guide Page 78 Main Menu Setup Video Local Monitoring LOCAL MONITORING CLOCK POSITION CAMERA NAME POSITION SEQUENTIAL SWITCH TIME SEQUENTIAL MODE CAMERAS DEFAULT DISPLAY MODE HORIZONTAL POSITION VERTICAL POSITION HORIZONTAL SCALE VERTICAL SCALE BOTTOM TOP 1SEC 1-3QUAD 5 0 10 2 The local monitoring menu contains the following options CLOCK POSITION CAMERA NAME POSITION SEQUENTIAL SWITCH TIME SEQUENTIAL MODE CAMERAS DEFAULT DISPLAY MODE HORIZONTAL POSITION VERTICAL POSITION HORIZON
PAGE 85
Tele Eye RX User Guide Page 79 Main Menu Setup Recording RECORDING RECORDING MODE DISK MODE QUALITY IMAGE SIZE CONTINUOUS CYCLIC EXCELLENT FULL The recording menu contains the following options : Change recording mode in 1, 2, 3, 4, 5 frame per second (FPS) and continuous setting : Select the fix or cyclic disk mode : Change recording quality with 5 levels : Change recording video size in FULL and QUAD RECORDING MODE DISK MODE QUALITY IMAGE SIZE Note that recording in cyclic disk mode can erase th
PAGE 86
Tele Eye RX User Guide Page 80 Main Menu Setup Switches Switch X Setting SWITCH X SETTING NAME TYPE SWITCH X LATCHING The switch (No.) setting menu contains the following options : Edit the name of the switch : Change the type of the switch, either latching or push-button type NAME TYPE Main Menu Setup Date Time Setup DATE / TIME DATE TIME 1. Press “Enter” 24 AUG 2005 15:18 button to select [DATE TIME] or [TIME] option DATE DATE 2.
PAGE 87
Tele Eye RX User Guide Page 81 Main Menu Setup Connection CONNECTION TCP / IP MODEM … … The connection setup menu contains the following options : Configure TCP/IP network related setting : Configure modem related setting TCP / IP MODEM Main Menu Setup Connection TCP / IP TCP / IP IP PORT SUBNET MASK ENABLE GATEWAY GATEWAY ENABLE DNS PRIMARY DNS SECONDARY DNS SURELINK 192.168.0.2 1024 255.255.255.0 NO 0.0.0.0 NO 0.0.0.0 0.0.0.
PAGE 88
Tele Eye RX User Guide Page 82 Main Menu Setup Connection TCP / IP sureLINK SURELINK ENABLED SURELINK ADDRESS REFRESH RATE YES WWW . . . . .
PAGE 89
Tele Eye RX User Guide Page 83 Main Menu Setup Event Handler EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE ... ... ... ... ... ... ...
PAGE 90
Tele Eye RX User Guide Page 84 Main Menu Setup Transmitter TRANSMITTER TRANSMITTER NAME REGISTRATION CHECKING UPGRADE RX304 YES ...
PAGE 91
Tele Eye RX User Guide Page 85 Main Menu Backup to CD-R BACKUP TO CDR START DATE START TIME BACKUP SIZE ( MB ) START BACKUP 01 AUG 2005 15:08 650 ENTER The backup to CD-R menu contains the following options : Set the start date of the footage : Set the start time of the footage : Change the backup size (10MB ~ 650 MB) : Start Backup CD-R operation, and TeleEye RX transmitter will search the footages from start date and time and calculate the end time of footage according to the footages size and back
PAGE 92
Tele Eye RX User Guide Page 86 Main Menu Scan / Format Disk SCAN / FORMAT DISK DEVICE TYPE MODEL NO SERIAL NO CAPACITY DISK USAGE SCANDISK FORMAT HDD MAXTOR XXXX XXXXXXX 41GB 52% ENTER ENTER The HDD management menu contains the following options : Show the device type : Show the device model no. : Show the device serial no.
PAGE 93
Tele Eye RX User Guide Page 87 B. Recording Log Menu RECORDING LOG TIME CAMERA 11 : 00 1234 12 : 00 ---4 13 : 00 ---14 : 00 -2-15 : 00 ---16 : 00 1--17 : 00 1--- 1. Press “Enter” EVENT ----------------------------- 12 – 13 AUG2005 REMARK SENSOR MOTION AUDIO VIDEOLOSS ---------------------------------------------------------- - - ------------------------------------------------------- button to choose play recording log, time search function and log time scale 2.
PAGE 94
Tele Eye RX User Guide Page 88 PLAY TIME SEARCH MONTH LOG DAY LOG HOUR LOG 10MIN LOG MINUTE LOG The play and log search menu contains the following options PLAY TIME SEARCH MONTH LOG DAY LOG HOUR LOG 10MIN LOG MINUTE LOG : Play the current selected record : Search specify time recording log and play it : Change the recording log scale to month : Change the recording log scale to day : Change the recording log scale to hour : Change the recording log scale to 10 minutes : Change the recording log scale t
PAGE 95
Tele Eye RX User Guide Page 89 C. PTZ Menu ENABLE YES PTZ ? NO 1. During live mode, user presses the “Live” 2. If user selects [YES] to enable the PTZ, then [PTZ OPTION] menu always pops up when user press the “Live” button to pop up the [ENABLE PTZ] menu button again. User selects [DISABLE PTZ] to disable PTZ function 3.
PAGE 96
Tele Eye RX User Guide Page 90 PTZ Menu PTZ Option PTZ OPTION RECALL PRESET PROGRAM PRESET RECALL PATROL STOP PATROL AUX CTRL IRIS CTRL FOCUS CTRL ZOOM CTRL AUTO DISABLE PTZ The PTZ option menu contains the following options RECALL PRESET : Move the PTZ camera to the preset position PROGRAM PRESET : Save the current position of the PTZ camera as the preset position RECALL PATROL : Select the preset patrol for the PTZ camera STOP PATROL : Stop the patrol for the PTZ camera AUX CTRL : Control the auxili
PAGE 97
Tele Eye RX User Guide Page 91 D. Recording Menu START RECORDING START RECORDING RECORDING CAMERA 1. Press the “Rec” 2. Using the “Up” ENTER 1234 button to pop up the main menu / “Down” button to select recording and set recording camera The recording menu contains the following options : Start recording operation : Select the camera for recording START RECORDING RECORDING CAMERA Recording Menu Recording Camera RECORDING CAMERA 1-3- 1. Using the “Left” 2. Press the “Up” 3.
PAGE 98
Tele Eye RX User Guide Page 92 E. Event Menu EVENT MENU EVENT STATUS ALARM LOG MOTION LOG VIDEOLOSS LOG SYSTEM TAMPER LOG ARM DISARM TAMPER LOG SECU. SWITCH TAMPER LOG POWER FAILURE LOG CONNECTION LOG 1. Press the “Event” 2. Using the “Up” ... ... ... ... ... ... ... ... ... button to pop up the event menu / “Down” button to select a sub-menu 3. A selected sub-menu option will be pointed by a hand cursor and highlighted 4. Press “Enter” button to confirm the selection and pop up the sub-menu 5.
PAGE 99
Tele Eye RX User Guide 7. You can press the “Back” Page 93 button back to previous menu and “Live” button to exit menu.
PAGE 100
Tele Eye RX User Guide Page 94 Event Menu Alarm Log ALARM LOG DATE TIME CHANNEL STATUS ACTION 03AUG05 03AUG05 02AUG05 02AUG05 01AUG05 01AUG05 01AUG05 01AUG05 ---4------4-----------2------------1------1-------------- RESET TGR ARM TAMPER SS ON RESET TGR ENTRY -----R- D - B- ------------- - -E------------ S- E - P ------ 12 : 45 : 18 12 : 29 : 46 09 : 50 : 33 09 : 35 : 02 11 : 05 : 03 10 : 25 : 36 10 : 10 : 10 09 : 29 : 17 Action R : Recording S : Switch D : Dial back E : Email B : Buzzer P : PT
PAGE 101
Tele Eye RX User Guide Page 95 Event Menu Video Loss Log VIDEOLOSS LOG DATE TIME CHANNEL STATUS 03AUG05 03AUG05 02AUG05 02AUG05 01AUG05 01AUG05 01AUG05 01AUG05 ---4------4-----------2-------3----1------1-------------- RESET TGR RESET TGR TGR RESET TGR RESET 12 : 45 : 18 12 : 29 : 46 09 : 50 : 33 09 : 35 : 02 11 : 05 : 03 10 : 25 : 36 10 : 10 : 10 09 : 29 : 17 ACTION -----R- D - B- -------- ------ - -E------------ S- E - P ------ Action R : Recording S : Switch D : Dial back E : Email B : Buzze
PAGE 102
Tele Eye RX User Guide Page 96 Event Menu Arm Input Tamper Log ARM INPUT TAMPER LOG DATE TIME STATUS ACTION 22AUG05 22AUG05 21AUG05 21AUG05 20AUG05 20AUG05 20AUG05 20AUG05 -----R- D - B- -------- - - E- --D-------- S- E - P ------ 12 : 45 : 18 12 : 29 : 46 09 : 50 : 33 09 : 35 : 02 11 : 05 : 03 10 : 25 : 36 10 : 10 : 10 09 : 29 : 17 RESET TGR RESET TGR TGR RESET TGR RESET Action R : Recording S : Switch D : Dial back E : Email B : Buzzer P : PTZ camera The arm input tamper log contains the follo
PAGE 103
Tele Eye RX User Guide Page 97 Event Menu Power Failure Log POWER FAILURE LOG DATE TIME STATUS ACTION 22AUG05 22AUG05 21AUG05 21AUG05 20AUG05 20AUG05 20AUG05 20AUG05 RESET TGR RESET TGR TGR RESET TGR RESET -----R- D - B-------- - -E------------ S- E - P ------ 12 : 45 : 18 12 : 29 : 46 09 : 50 : 33 09 : 35 : 02 11 : 05 : 03 10 : 25 : 36 10 : 10 : 10 09 : 29 : 17 Action R : Recording S : Switch D : Dial back E : Email B : Buzzer P : PTZ camera The power failure log contains the following status
PAGE 104
Tele Eye RX User Guide Page 98 Event Menu XXXX Log Search Log For each log, you can press “Enter” button to enter the log option, and press “Enter” button in [TIME SEARCH] option to enter search log menu.
PAGE 105
Tele Eye RX User Guide Page 99 SECTION 6 Advanced Operation A. Install TeleEye RX with Alarm Sensors and Relay Control Port TeleEye RX304 supports up to 4 alarm ports with tamper detection for connecting with alarm sensors, 4 additional input sensors and 4 relay ports for control. The definitions of alarm and relay control ports are shown in the following diagram.
PAGE 106
Tele Eye RX User Guide Page 100 B. Install TeleEye RX with Tamper Circuit and External Resistors TeleEye RX supports tamper detection (DEOL and SEOL) on all alarm inputs, arm/disarm input, security switch input, system tamper and power failure input.
PAGE 107
Tele Eye RX User Guide Page 101 Single End of Line Configuration C A sensor drive output wire B Normal Close (NC) A sensor drive output wire B Normal Open (NO) Term Status Description S/C TAMPER Wire short (point A and B) LoZ NORMAL Sensor drive output close (point B and C) O/C ALARM Sensor drive output open (point B and C) Term Status Description S/C ALARM Sensor drive output close (point A and B) LoZ NORMAL Sensor drive output open (point A and B) O/C TAMPER Wire open (point A and B) Without T
PAGE 108
Tele Eye RX User Guide Page 102 Notes: The below table shows the summary between the resistance network and the condition result. Note that this table is used as a reference. There may be a 10% tolerance for the resistance value in the below table. Resistance (Ω) Condition 0~400 DEOL (Normal Close) Tamper Short DEOL (Normal Open) Tamper Short 401~2780 2781~29.5k 29.
PAGE 109
Tele Eye RX User Guide Page 103 C. Event Handling TeleEye RX transmitter supports 7 events and their icons are as follows. 1. Arm/Disarm 2. Security Switch 3. Alarm 4. Motion 5. Videoloss 6. System Tamper 7. Power Failure TeleEye RX supports 7 actions which can be activated by any events as above. 1. Recording 2. Switch 3. Dialback 4. Buzzer 5. Event LED 6. Live Camera 7. PTZ Event and Action Icons in Local CCTV Monitor The icons of the 7 events are shown as above.
PAGE 110
Tele Eye RX User Guide Page 104 I. Arm/Disarm Arm/Disarm Arm/Disarm input is used for enhancing security level of the surveillance area. This input introduce the concept of 3 zone types for alarm, fire zone, normal and entry exit zone. Armed If the system is armed, alarm sensor in normal zone type can be triggered immediately if someone triggers the sensor.
PAGE 111
Tele Eye RX User Guide Page 105 Zone Type Although the setting of zone type belongs to alarm menu, it is worth to discuss as below. Fire Zone This zone allows alarms to trigger no matter which arm state of the system is, i.e. armed or disarmed. It is suitable for installation of fire detectors Normal This zone allows alarms to trigger after armed. Entry/Exit Zone This zone allows user to set the delay time for entering or leaving the surveillance area without triggering any alarm event.
PAGE 112
Tele Eye RX User Guide Page 106 EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE Step 2: Select [ARM/DISARM] option and ... ... ... ... ... ... ... button to show arm/disarm setting menu. Step 3: Select [ENABLED] option and use ARM / DISARM ENABLED ARM STATE TAMPER TYPE ASSOCIATE SWITCH TAMPER EVENT ACTION press “Enter” YES CLOSE NONE NO … “Left” or “Right” button to enable (i.e. set the value to [YES]) the arm/disarm function.
PAGE 113
Tele Eye RX User Guide Page 107 Step 6: Select [ASSOCIATE SWITCH] ARM / DISARM ENABLED ARM STATE TAMPER TYPE ASSOCIATE SWITCH TAMPER EVENT ACTION YES CLOSE DEOL YES … option and use “Left” “Right” or button to select [YES] and enable switch 1 only for arm/disarm associate switch. Switch 1 will be ON when TeleEye RX is armed. Switch 1 will be OFF when TeleEye RX is disarmed. Switch 1 cannot be activated by other events any more if it is an associate switch of arm/disarm.
PAGE 114
Tele Eye RX User Guide Page 108 II. Security Switch Security Switch It is an input to the transmitter for wiring a security switch. The purpose of the security switch is to terminate the exit delay for exit zone alarm. If the security switch is on and the system is armed, all exit delay will be terminated. If the security switch is off and an entry alarm triggered, entry delays will start.
PAGE 115
Tele Eye RX User Guide Page 109 Security Switch Setup Procedure Step 1: Press “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER SHUT DOWN ... ... ... ... ... ... ... ENTER button, select [SETUP] option and press “Enter” button to enter [SETUP] sub menu. Select [EVENT HANDLER] option and press “Enter” EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE Step 2: Select [SECURITY SWITCH] option ... ... ... ... ... ... .
PAGE 116
Tele Eye RX User Guide Page 110 Step 5: Select [TAMPER TYPE] option and SECURITY SWITCH ENABLED ON STATE TAMPER TYPE ASSOCIATE SWITCH TAMPER EVENT ACTION YES CLOSE DEOL NO … use “Left” or “Right” button to choose security switch tamper circuit type according to the configuration of TeleEye RX security switch tamper circuit type.
PAGE 117
Tele Eye RX User Guide Page 111 III. Alarm Alarm It is an input to the transmitter from external alarm sensors. Alarm can be used to detect many events occur at the surveillance area, such as fire and illegal entering by someone. The alarm event supports BS 8418:2003 which has arm/disarm and security switch function. Sensor Tamper Type Alarm tamper event triggers if someone cuts the wire between the alarm input and the transmitter.
PAGE 118
Tele Eye RX User Guide Page 112 Example of Entry/Exit Zone WITH Security Switch Usage For Entry Zone : Entry Surveillance zone DISARM Alarm 1 Alarm 2 Alarm 3 Alarm 4 TeleEye RX Security Switch Delay1 Delay2 Delay3 Delay4 Time line The entry delay is the period of time between entering the surveillance zone and reaching the transmitter. In order to disarm the system for maintenance or repair, user / installer needs to turn off the security switch and enter the surveillance zone.
PAGE 119
Tele Eye RX User Guide Page 113 For Exit Zone : Exit Surveillance zone ARM Alarm 1 Alarm 2 Alarm 3 Alarm 4 TeleEye RX Security Switch Delay1 Delay2 Delay3 Delay4 Time line The exit delay is the period of time for leaving a surveillance zone without making false alarm (i.e. Alarm 1, Alarm 2, Alarm 3 and Alarm 4). The purpose is to let the user / installer have enough of time to leave the surveillance zone after the transmitter is armed. User / installer can set the delay time for each alarm.
PAGE 120
Tele Eye RX User Guide Page 114 Example of Entry/Exit Zone WITHOUT Security Switch Usage For Entry Zone : Entry Surveillance zone DISARM Alarm 1 Alarm 2 Alarm 3 Alarm 4 Delay1 Delay2 Delay3 Delay4 TeleEye RX Time line The entry delay is the period of time between entering the surveillance zone and reaching the transmitter.
PAGE 121
Tele Eye RX User Guide Page 115 For Exit Zone : Exit Surveillance zone ARM Alarm 1 Alarm 2 Alarm 3 Alarm 4 Delay1 Delay2 Delay3 Delay4 TeleEye RX Time line The exit delay is the period of time for leaving a surveillance zone without making false alarm (i.e. Alarm 1, Alarm 2, Alarm 3 and Alarm 4). The purpose is to let the user / installer have enough of time to leave the surveillance zone after the transmitter is armed. User / installer can set the delay time for each alarm.
PAGE 122
Tele Eye RX User Guide Page 116 Different Combination Cases of Arm/Disarm, Security Switch and Alarm for the 3 Zone Type Initial State Step 1 Arm Security Switch Step 2 Step 3 Result Alarm Fire Zone Arm On No trigger Trigger alarm \ \ Alarm trigger Arm Off No trigger Trigger alarm \ \ Alarm trigger Arm Uninstall No trigger Trigger alarm \ \ Alarm trigger Disarm \ No trigger Trigger alarm \ \ Alarm trigger Uninstall \ No trigger Trigger alarm \ \ Alarm trigger Unins
PAGE 123
Tele Eye RX User Guide Page 117 Initial State Step 1 Arm Security Switch Step 2 Step 3 Result Alarm Entry / Exit Zone Trigger alarm. Arm On No trigger Security switch off No alarm trigger. Disarm Recording stops Entry delay starts. Recording starts (if Alarm is triggered recording action is Recording does not Arm enabled) stop unless user disarm the system Trigger alarm. Exit delay starts.
PAGE 124
Tele Eye RX User Guide Page 118 Alarm Setup Procedure SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER SHUT DOWN Step 1: Press “Menu” ... ... ... ... ... ... ... ENTER button, select [SETUP] option and press “Enter” button to enter [SETUP] sub menu. Select [EVENT HANDLER] option and press “Enter” button. Step 2: Select [ALARM] option and press EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE ... ... ... ... ... ... ...
PAGE 125
Tele Eye RX User Guide Page 119 Step 5: Select [SENSOR TAMPER TYPE] ALARM 1 SETTING ENABLED SENSOR NAME SENSOR TYPE SENSOR TAMPER TYPE ZONE TYPE ENTRY DELAY EXIT DELAY ACTION YES ALARM 1 NC DEOL NORMAL 0 SEC 0 SEC … or option and use “Left” “Right” button to choose alarm sensor tamper circuit type according to the configuration of TeleEye RX alarm sensor tamper circuit type.
PAGE 126
Tele Eye RX User Guide Page 120 IV. Motion Motion Motion detection can be triggered when motion occurs on the camera. Motion detection has different sensitivity levels. For motion event on each video input channel, it depends on the motion of selected area. User should setup the select motion areas and sensitivity. Motion detection has generally 4 options : high, middle, low and custom. Custom option allows user to select the sensitivity level and area by themselves.
PAGE 127
Tele Eye RX User Guide Page 121 Motion Setup Procedure Step 1: Press “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER option and press “Enter” button to enter [SETUP] sub menu. Select [EVENT HANDLER] option and press “Enter” button. Step 2: Select [MOTION] option and press EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE button, select [SETUP] ... ...
PAGE 128
Tele Eye RX User Guide Page 122 Step 4: Setting motion detection as follow: Deselected Area Selected Area ENABLED: enable the motion detection of the camera DESELECT: deselect motion area SELECT: select motion area DESELECT ALL: clear all motion block SELECT ALL: select all motion block RESTORE: restore previous motion setting SENS: sensitivity option : LOW, MID, HIGH, CUSTOM OK: finish, save the setting and exit the detection menu Step 5: Select [ACTION] option and press MOTION 1 SETTING MOTION DETECT
PAGE 129
Tele Eye RX User Guide Page 123 V. Video Loss Video Loss Video loss can be triggered when the video channel input disappears. It will happen if the transmitter receives no signal from the camera. The local CCTV monitor displays a blue screen for video loss condition. Video Loss Setup Procedure Step 1: Press “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ...
PAGE 130
Tele Eye RX User Guide Page 124 VIDEO LOSS X SETTING ENABLED ACTION YES … Step 4: Select [ACTION] option and press “Enter” button to select alarm trigger or tamper action.
PAGE 131
Tele Eye RX User Guide VI. Page 125 System Tamper System Tamper Input It is an input to the transmitter for wiring a tamper switch of the external cabinet outside the transmitter and its accessories. The purpose of system tamper event is to prevent someone to break into the cabinet and destroy the transmitter. Sensor Type The system tamper input circuit type is normal close (NC). The state of the circuit is close, it indicates normal of TeleEye RX.
PAGE 132
Tele Eye RX User Guide Page 126 Step 2: Select [SYSTEM TAMPER] option and EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE ... ... . . .. ... ... ... ... press “Enter” button to show the system tamper menu and press “Enter” button to enter the System Tamper setting menu. Step 3: Select [ENABLED] option and use SYSTEM TAMPER ENABLED SENSOR TYPE ACTION YES NO … “Left” or “Right” button to enable (i.e.
PAGE 133
Tele Eye RX User Guide Page 127 VII. Power Failure Power Failure Input It is an input to the transmitter typically used for wiring the output signal pin from UPS. Sensor Type The power failure input circuit type is normal close (NC). The state of the circuit is close, it indicates normal of TeleEye RX. Otherwise, the state of the circuit is open, it indicates power failure of TeleEye RX. The power failure input circuit type is normal open (NO).
PAGE 134
Tele Eye RX User Guide Page 128 Step 2: Select [POWER FAILURE] option and EVENT HANDLER ARM / DISARM SECURITY SWITCH ALARM MOTION VIDEO LOSS SYSTEM TAMPER POWER FAILURE ... ... . . .. ... ... ... ... button to enter the power failure setting menu. Step 3: Select [ENABLED] option and use “Left” POWER FAILURE ENABLED SENSOR TYPE ACTION press “Enter” YES NO … or “Right” button to enable (i.e. set the value to [YES]) power failure event handler.
PAGE 135
Tele Eye RX User Guide Page 129 D. Event Action TeleEye RX supports event actions such as Recording, Switch, Dial back, Buzzer, Event LED, Live camera and PTZ when event detected from alarm, tamper of alarm, motion, video loss, tamper of arm/disarm, tamper of security switch, power failure and system tamper. Event Action Setup Procedure Step 1: Press “Menu” SETUP MENU VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ...
PAGE 136
Tele Eye RX User Guide I. Page 130 Recording Recording If an event triggers, recording can record the video content at user selected camera with selected recording mode. Pre-Alarm Recording Pre-alarm recording allows to record video before an event trigger. The period of pre-alarm recording is at least 1 minute (not more than 2 minutes) before the event trigger. User can find that there is at least 1 minute more video content in [RECORDING LOG MENU] before event trigger.
PAGE 137
Tele Eye RX User Guide XXXXXXX RECORDING ENABLED YES DURATION AFTER EVENT CLEAR 20 SEC RECORDING MODE CONTINUOUS RECORDING CAMERA ---- Page 131 Step 2: Select [ENABLED] option and use “Left” or “Right” button to enable (i.e. set the value to [YES]) recording action. Step 3: Select the [DURATION AFTER EVENT CLEAR] and [RECORDING MODE] options and uses the “Left” “Right” or button to choose the suitable setting.
PAGE 138
Tele Eye RX User Guide II. Page 132 Switch Switch allows transmitter to control 4 external relays which are defined by user. Switch Type Switch has 2 types. They are latching or push-button type. In latching type, the switch turns on for a period of time. In push-button type, the switch turns on and off after 1 second. Latching Duration The latch duration period is the time for turning on the switch. Action Delay The delay is the period of time after turning off the switch before next turning on.
PAGE 139
Tele Eye RX User Guide Page 133 Step 2: Select [ENABLED] option and use “Left” XXXXXXX SWITCH ENABLED SWITCHES ENABLED GENERAL SWITCH SETTING YES ---... or “Right” button to enable (i.e. set the value to [YES]) switch action. Step 3: Select [SWITCHES ENABLED] option button to enable or and press “Enter” disable the switches. Step 4: Use the “Left” ASSOCIATE SWITCH or “Right” button to select switch and press the “Up” 1-3- or “Down” button to enable or disable switch.
PAGE 140
Tele Eye RX User Guide Page 134 Step 8: Select [NAME] option and press “Enter” SWITCH X SETTING NAME TYPE SWITCH X LATCHING button to edit the name of switch (No.). Step 9: Select [TYPE] option and press the “Left” or “Right” button to choose the switch type. Press the “Back” button to go back the general switch setting menu and save the setting. Step 10: Select [LATCH DURATION] option and GENERAL SWITCH SETTING SWITCH 1 SWITCH 2 SWITCH 3 SWITCH 4 LATCH DURATION ACTION DELAY ... ... ... ...
PAGE 141
Tele Eye RX User Guide III. Page 135 Dialback Dialback Dialback allows the transmitter to connect to one remote PC and displays live video if an event triggers. Therefore, remote operator can recognize what situation is at the surveillance area. Retry Duration The retry duration is the period between each dialback retrial (in second). Retry Count The retry count is the number of dialback retrial if dialback fails.
PAGE 142
Tele Eye RX User Guide Page 136 Step 4: Select [RETRY DURATION] option and press the “Left” or “Right” button to choose the retry duration. Step 5: Select [RETRY COUNT] option and press the “Left” or “Right” button to choose the retry count. DIALBACK PHONE X SETTING IP PORT Step 6: Select [PHONE (No.)] option and press 192.168.0.10 2048 “Enter” button to enter the dialback IP setting menu. Step 7: IP Select [IP] option and press “Enter” or button to set IP. Use “Left” IP : 210. 17.139.
PAGE 143
Tele Eye RX User Guide Page 137 Step 10: Run WX-30 software at the local network PC. (For details of WX-30 software installation, please refer to WX-30 Software Guide) Step 11: Press [Alarm Standby] icon for activating dialback action standby Step 12: [Alarm Password] message broad pops up.
PAGE 144
Tele Eye RX User Guide IV. Page 138 Buzzer Buzzer This buzzer contains inside the TeleEye RX transmitter. It can produce “Beep” sound in order to draw nearby operator attention about an event trigger. Duration Duration is the period for turning on the buzzer. Action Delay Action delay is the period after turning off the buzzer turning on.
PAGE 145
Tele Eye RX User Guide Page 139 GENERAL BUZZER SETTING DURATION ACTION DELAY 10SEC 10SEC Step 5: Select [ACTION DELAY] option and press the “Left” or “Right” button to choose the action delay Step 6: You can press “Live” button to exit OSD menu or press “Back” enter action menu again.
PAGE 146
Tele Eye RX User Guide V. Page 140 Event LED Event LED The event LED is the LED built on the front panel of TeleEye RX transmitter . If an event trigger, the LED is blinking until the event is clear. Event LED Action setup procedure Step 1: In the action menu, select [EVENT LED] XXXXXXX ACTION RECORDING SWITCH DIALBACK BUZZER EVENT LED LIVE CAMERA PTZ … … … … … … … button to enter the event LED action setting menu.
PAGE 147
Tele Eye RX User Guide VI. Page 141 Live Camera Live Camera Event associate live camera display real time live video of pre-selected camera if an event triggers, so operator can immediately know what happen from the site. Live camera action can only display live video one time before user clears the event.
PAGE 148
Tele Eye RX User Guide Page 142 Step 3: Select [ASSOCAITE CAMERA] option ASSOCIATE CAMERAS 1-3- and press “Enter” button to enter the live camera action setting menu. Use the “Left” or “Right” button to select camera and press the “Up” “Down” or button to enable or disable camera. Press “Enter” button to save the camera setting and go back to live camera action menu. Step 4: You can press “Live” button to exit OSD menu or press “Back” enter action menu again.
PAGE 149
Tele Eye RX User Guide Page 143 VII. PTZ PTZ Camera PTZ camera action allows the pan tilt zoom camera to go to user preset position for viewing what happen if an event trigger. PTZ Action setup procedure XXXXXXX ACTION RECORDING SWITCH DIALBACK BUZZER EVENT LED LIVE CAMERA PTZ Step 1: In the action menu, select [PTZ] option … … … … … … … button to enter the PTZ action setting menu.
PAGE 150
Tele Eye RX User Guide Page 144 Step 4: Select [RECALL PRESET] option and XXXXXX X PTZ ENABLED ASSOICATE CAMERA RECALL PRESET YES ---1 use the “Left” or “Right” button to select camera and press the “Up” or “Down” button to choose the preset position of the PTZ camera. Step 5: You can press “Live” button to exit OSD menu or press “Back” enter action menu again.
PAGE 151
Tele Eye RX User Guide Page 145 E. Backup to CD-R TeleEye RX transmitter supports backup function in a CD-R and provides maximum backup storage size of 650MB. The CD-R will be auto run with the portable player software after inserted into PC. Note that recommended physical size of CD-R should be 120mm / 5.25" Backup to CD-R Setup Procedure Step 1: Press “Menu” MAIN MENU SETUP BACKUP TO CD-R SWITCH CONTROL SCAN / FORMAT DISK TRANSMITTER INFO SHUT DOWN ... ... ... ... ...
PAGE 152
Tele Eye RX User Guide Page 146 Step 4: Select [START BACKUP] option and BACKUP RECORDING press “Enter” START TIME : 18 AUG 2005 10 : 18 END TIME : 18 AUG 2005 12 : 18 START BACKUP ? YES button to show [BACKUP RECORDING] message board and it shows user about the end NO time. Select [YES] option and press “Enter” button to start backup function. Step 5: During the backup preparation, the BACKUP RECORDING PLEASE INSERT A BLANK CD YES NO transmitter will request you to insert a blank CD.
PAGE 153
Tele Eye RX User Guide Page 147 Step 7: Insert the CD to PC with window OS and the Portable Player software will pop up automatically. Press “Play” button for playback in the CD. Note that if the Portable Player software does not pop up automatically, please uses the mouse to double click the CD-ROM drive in your PC.
PAGE 154
Tele Eye RX User Guide Page 148 F. Connection with PTZ cameras As TeleEye RX transmitter built with a RS485 port IN and OUT, you can connect port OUT to Pan/Tilt/Zoom cameras (in parallel) and connect port IN to keyboard controller. The connection diagram is shown below. Setup Procedure For installation of CCTV monitor, cameras, network setting and connection, please refer to P.66 of the User Guide. Step 1: Connect the P/T/Z cameras to the RS 485 OUT port in parallel at the TeleEye RX rear panel.
PAGE 155
Tele Eye RX User Guide Page 149 Configure P/T/Z cameras driver and setting as follow: SETUP MENU Step 4: Press “Menu” VIDEO RECORDING SWITCHES DATE / TIME CONNECTION EVENT HANDLER TRANSMITTER RESTORE FACTORY SETTING ... ... ... ... ... ... ... ENTER button, select [SETUP] option and press “Enter” button to enter [SETUP] sub menu. Select [VIDEO] option and press “Enter” button. Step 5: Select [CAMERA SETTING] option and VIDEO CAMERA SETTING LOCAL MONITORING OSD COLOR VIDEO FORMAT ... ...
PAGE 156
Tele Eye RX User Guide Page 150 ADVANCED PTZ SETTING PTZ DRIVER BIT RATE TELEEYE DM S . . . 4800 Step 8: Select [PTZ DRIVER] option and press “Enter” button to select P/T/Z cameras driver. According to the P/T/Z Note that if there is no driver to support your P/T/Z cameras, please refer to WX-30 software upload camera model, please select a certain driver for required PTZ camera and press “Enter” PTZ driver section button to save the setting.
PAGE 157
Tele Eye RX User Guide Page 151 PTZ MOVEMENT SETTING PAN DURATION TILT DURATION ZOOM DURATION FOCUS DURATION IRIS DURATION ADDITIONAL DURATION WASHER DURATION WIPER DURATION PATROL SPEED DWELL TIME Step 12: User can select different movement 5 5 3 3 3 3 3 3 3 2 direction duration according to whether the PTZ camera support those functions. Step 13: Press “Back” button for several time to exit main menu. Use “Camera Control” buttons (as below) to select the PTZ camera.
PAGE 158
Tele Eye RX User Guide Page 152 APPENDIX A sureLINK TECHNOLOGY sureLINK technology is available in TeleEye RX, which enables you to connect to the transmitter with broadband dynamic IP Internet connection. If you can only use broadband dial-up account to connect to the Internet through your computer, sureLINK provides a solution for sharing the Internet connection between your computer and the transmitter.
PAGE 159
Tele Eye RX User Guide Page 153 How to Apply for sureLINK Address You can apply for sureLINK by visiting our web site at http://www.TeleEye.com Step 2 Step 1 Step 1: Sign up to create your user account Step 2: Login the page using your registered name and password.
PAGE 160
Tele Eye RX User Guide Page 154 ʳ ʳ ʳ ʳ ʳ ʳ Step 4 ʳ ʳ ʳ Step 4: Enter a sureLINK address (Domain Name), your Transmitter Serial No. and Registration Code in the fields provided respectively. Then click the Apply button. The process is then completed. After we received your domain name registration for your transmitter, your application will be processed. Normally, it requires about 2 to 3 working days to activateʳ sureLINK for your transmitter.
PAGE 161
Tele Eye RX User Guide Page 155 ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ ʳ Step 2 ʳ ʳ Step 2: Enter the Old Registration Code, New Transmitter Serial Number and New Registration Code at each field provided. Click Modify button to submit the form. ʳ ʳ ʳ ʳ ʳ ʳ Step 4 Step 3 ʳ ʳ ʳ ʳ If the above procedure is completed successfully, theʳsureLINKʳwill be effective immediately.
PAGE 162
Tele Eye RX User Guide Page 156 APPENDIX B GENERAL TERMS DISCUSSION Before you start to configure the transmitter, you may need to know some of the terms and information used in the transmitter. Registration Checking Users need to do the registration in the TeleEye Reception Software WX-30 for authorization before the transmitter can be used when such feature is enabled in the TeleEye RX.
PAGE 163
Tele Eye RX User Guide Page 157 APPENDIX C SPECIFICATIONS STANDARD NO. OF CHANNELS STANDARD NO. OF CHANNELS DISPLAY SCREEN DISPLAY FRAME RATE TYPE INPUT OUTPUT NETWORK CONCURRENT USERS sureLINK MODEM PORT TELEMETRY CONTROL MODE HD TYPE MAX.
PAGE 164
Tele Eye RX User Guide Page 158 RELAY SWITCH NO. OF CHANNELS MAX. RATING 4 24V AC, 1000mA POWER VOLTAGE MAX. RATING AMBIENT TEMPERATURE RELATIVE HUMIDITY DIMENSION WEIGHT 12V DC 50W OPERATING ENVIRONMENT 5oC – 45oC <85% (no condensation) MECHANICAL DESIGN 403x370x125 (mmxmmxmm) 3.