NF Series Network Camera NF610 Installation Guide
Notice: Signal Communications Limited reserves the right to make improvements to the product described in this manual at any time and without notice. This manual is copyrighted. All rights are reserved. This manual may not be copied, reproduced or translated in whole or part without prior consent from Signal Communications Limited. TeleEye is a trademark of Signal Communications Limited and is registered in China, Hong Kong, US and other countries.
FCC Statement on Class B WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents PREFACE BEFORE YOU BEGIN 1 SECTION 1 INTRODUCTION • Features 4 5 SECTION 2 INTERFACE DESCRIPTION • Model: NF610 6 SECTION 3 FIRST TIME SET UP OF THE NETWORK CAMERA • Network Camera Setup with IP Setup Utility • Network Camera Setup with Crossover Ethernet Cable • Network Camera Setup with Built-in Web-based Configuration 8 10 10 SECTION 4 SYSTEM CONFIGURATION AND INSTALLATION • • General System Configuration • 12 What you need General Configuration of Network Camera A1.
SECTION 6 GENERAL TERMS DISCUSSION • Registration Checking • Video Mode • Built-in Web Server • Site Monitoring Method 22 22 22 23 SECTION A APPENDIX • IP Address Setup for Window 98/ME • IP Address Setup for Window NT/2000/XP • Router Configuration 24 27 38 SECTION B SPECIFICATIONS • Model: NF610 29
Tele Eye III+ Network Camera Installation Guide Page 1 PREFACE BEFORE YOU BEGIN Modification of the Power Adapter The connector of the power adapter might require some modifications before connecting it to the Network Camera. 1. Use a cutting tool to cut off the connector of the adapter 2. Strip the plastic covering off from the cable. You should see the cable is of the coaxial type Braided GND 12V wire Plastic Covering Plastic Shield 3.
Tele Eye III+ Network Camera Installation Guide Page 2 Repositioning of the Mounting Plate At the bottom of the Network Camera is a mounting plate. The mounting plate can also be removed and re-attached to the top of the Network Camera. The following is the procedure for repositioning the mounting plate from the bottom to the top of the Network Camera. IMPORTANT: TO PREVENT DISMANTLING OF THE NETWORK CAMERA, DO NOT SIMPLY REMOVE ALL THE SCREWS FROM THE MOUNTING PLATE. Please follow the procedures below.
Tele Eye III+ Network Camera Installation Guide Page 3 4. Re-secure the screws just removed to position 1 and 2 at the bottom of the Network Camera. This is to prevent the dismantling of the camera. 5. Remove the screws in position 5 and 6. 6. Re-attach the screws just removed to position 3 and 4 at the bottom of the Network Camera 7. Position and align the mounting plate to the screw holes at the top of the camera 8. Put on the rest of the screws to fasten the plate to the camera.
Tele Eye III+ Network Camera Installation Guide Page 4 SECTION 1 INTRODUCTION The Tele Eye III+ Network Camera NF 610 is a brand new member of the Tele Eye III+ Network CCTV family. It combined the power of high performance imaging technology and swift video transmission into a single module. With the built-in web server, remote video surveillance can readily be conducted with standard web browsers over the Internet or LAN.
Tele Eye III+ Network Camera Installation Guide Page 5 Features • • • • • • • • • • • • • • • • • 1/3” colour CCD Illumination 1 Lux Back light compensation Flexible connections – Internet, LAN, ADSL and cable modem Real time video transmission up to 30 fps over LAN for NTSC; up to 25 fps over LAN for PAL Resolution up to 640x480 pixels Support static and dynamic IP Built-in web server Event-driven recording Composite video output Web video development tool Mobile video on pocket PC Event management Pre-
Tele Eye III+ Network Camera Installation Guide Page 6 SECTION 2 INTERFACE DESCRIPTION Model: NF610 The rear panel of the TeleEye III+ Network Camera NF610 is shown below: Functional Description of NF610 Collision & Link LED Status - COL LED: when on, indicates that collision is occurring on the network - LINK LED: when on, indicates that TeleEye III+ Network Camera is connecting to the network and ready to function Ethernet Socket (10/100 Base-T) - This socket is used for connecting TeleEye III+ Netw
Tele Eye III+ Network Camera Installation Guide P4 P3 P2 P1 PIN P1 P2 P3 P4 Page 7 Signal PIN for alarm device (NC / NO) Common GROUND Dry Contact Dry Contact Power LED - PWR LED: when on, indicates that the Network Camera has been power up successfully VIDEO OUT Connector - Standard BNC connector for color video - A composite video signal should be supplied from this connector Power Terminal - A power terminal for the connection to the power supply (12V D.C.
Tele Eye III+ Network Camera Installation Guide Page 8 SECTION 3 FIRST TIME SETUP OF THE NETWORK CAMERA Before installing the Network Camera, its IP address must be set so that an Ethernet connection can be established to the Network Camera from a computer. In order to do this, either the IP address of the Network Camera or the IP address of the PC should be modified. This is very important since the Network Camera has default IP address, 192.168.0.
Tele Eye III+ Network Camera Installation Guide Page 9 Step 4: Select “NF” and enter Model No. (e.g. NF-610). Step 5: Enter the Network Camera Serial Number and Registration Code to the fields provided. Step 6: Insert a new, valid IP address of your desire to the provided field (e.g. 192.168.0.3). Step 7: Click on Set Transmitter IP button to set the Network Camera to the new IP address.
Tele Eye III+ Network Camera Installation Guide Page 10 Network Camera Setup with Crossover Ethernet Cable Your computer is required to change the IP address (e.g. 192.168.0.3). Please refer to Section A Appendix for a detailed descriptions for IP configuration on different operating systems. If your computer has changed the IP address, you can connect Network Camera by plugging Crossover Ethernet Cable from your computer to Ethernet port of Network Camera.
Tele Eye III+ Network Camera Installation Guide Page 11 Step 2: You can change the connection, sureLINK, transmitter properties and camera control settings. You can reload the configuration by clicking Reload button. Click on Save & Exit button to save the changes. The description of each setting type is listed below: Setting Type Connection Settings sureLINK Settings Transmitter Settings Description You can set IP address, port, subnet mask, gateway and DNS as well as TeleEye Proxy Server settings.
Tele Eye III+ Network Camera Installation Guide Page 12 SECTION 4 SYSTEM CONFIGURATION AND INSTALLATION This section will discuss how to setup the Network Camera and modify its settings in details. Installations of the Network Camera with different types of network will also be discussed. Specifically, installations with the following types of network will be discussed. Network Types: A1. A2. B1. B2.
Tele Eye III+ Network Camera Installation Guide Page 13 RJ-45 Network Cable It is a shielded, straight-through RJ-45 network cable. The cable will connect the Tele Eye III+ Network Camera to the hub of the LAN for typical application. Crossover Network Cable Used to connect between a router and PC or the Network Camera Software Web-browser A standard web-browser such as IE, and Netscape…etc. Information Valid IP address for the Network Camera.
Tele Eye III+ Network Camera Installation Guide Page 14 General Configuration of Network Camera After you prepared all the things discussed in previous section, you should be ready to configure the Network Camera. Note: Make sure the computer in use is capable of connecting to the Internet or the Local Area Network (LAN). Also make sure your browser supports Java. Step 1: Plug the RJ-45 network cable into the socket on the hub's/switch’s rear panel.
Tele Eye III+ Network Camera Installation Guide Page 15 The Network Camera’s web-based configuration should already be displayed in your webbrowser. It should be similar to the captured screen shown below. Please enter the default administrator password “000000” to login.
Tele Eye III+ Network Camera Installation Guide Page 16 There are many settings to be configured, such as Video Mode, Gateway, DNS…etc. The camera features can also be configured now. For users who have little knowledge in camera settings, it is advised that users read the section in camera features before making any changes.
Tele Eye III+ Network Camera Installation Guide Page 17 A1. For Internal LAN Access Step 1: To continue, configure the Registration Checking and Video Mode settings. Step 2: You can Enable the Built-in Web Server so that you can see video through web browser Step 3: Ensure all settings are correct, then press the Save and Exit button Network Camera Installation RJ-45 Network Cable Hub Step 1: Plug the RJ-45 network cable into the socket on the hub's rear panel.
Tele Eye III+ Network Camera Installation Guide Page 18 Step 6: You may now use the web-based graphical user interface or the TeleEye III+ Reception Software to connect to the Network Camera. For the instructions of using the software, please refer to the TeleEye III+ Reception Software User Guide. A2. For Broadband Internet Connection with Static IP Internet Please follow the configuration and installation steps of A1. Internal LAN Access. You have to set the Gateway IP of the Network Camera.
Tele Eye III+ Network Camera Installation Guide Page 19 SECTION 5 NORMAL OPERATIONS OF THE NETWORK CAMERA Having completed the IP setup of the Network Camera, you are now ready to see live streaming video from the Network Camera. To start viewing video, all that is required is a computer with network capability and a Java supporting, standard web browser. To view video from the Network Camera is very similar to how you browse the Internet.
Tele Eye III+ Network Camera Installation Guide Page 20 Step 4: A window should appear. Please enter the password. The default password is 000000. The location name and the password can both be changed with the TeleEye III+ Reception Software, WRS3-AD. If problems arise, please check that your browser supports Java. You might need to enable Java or to download the latest version of the Java VM (go to http://java.sun.com/getjava/index.html).
Tele Eye III+ Network Camera Installation Guide Page 21 The main screen is where most actions take place. Location Name Exit Button Image Quality Clear Alarm Button Maximize Button Switch Control This web-based approach is the simplest way to connect with Network Camera. No other special software is required; it is just as easy as ordinary web browsing. On the other hand, the Tele Eye III+ Reception Software WRS3-AD can also be employed to connect and to view live video from the Network Camera.
Tele Eye III+ Network Camera Installation Guide Page 22 SECTION 6 GENERAL TERMS DISCUSSION To familiarize you with the Network Camera, you may need to know some of the terms and information below. Registration Checking Users need to do the registration in the Reception Software (e.g. WRS3-AD) for authorization before the Network Camera can be used when such feature is enabled in the TeleEye III+ Network Camera.
Tele Eye III+ Network Camera Installation Guide Page 23 Site Monitoring Method There are mainly three methods to link up with the Network Camera to see videos: TCP/IP in LAN TCP/IP on the Internet using Broadband and Internet Router TCP/IP on the Internet using Broadband with Dial-up Software You have to choose one of the System Configuration Methods in earlier section to configure TeleEye III+’s Network Camera before use so as to make it function properly.
Tele Eye III+ Network Camera Installation Guide Page 24 SECTION A APPENDIX IP Address Setup for Windows 98/ME The follow procedures will set your Ethernet Card IP address manually for your local LAN purpose. Note that these procedures will NOT affect your PC to get on the Internet. If you discover that you cannot be able to access on the Internet after applying the settings, you have to undo the settings or re-install the software provided by your ISP and retry the steps again.
Tele Eye III+ Network Camera Installation Guide Page 25 Two of them are very important for setup. One of them is used for your local intranet (the field may contain the name of your Ethernet card), the other one is used for your broadband Internet connection. An example is shown in the following figure. TCP/IP-> HP EN1207D-TX PCI 10/100 Fast Used for Intranet (local network) Ethernet Adaptor TCP/IP-> Network TeleSystems P.P.P.o.
Tele Eye III+ Network Camera Installation Guide Page 26 Step 7: Select your Ethernet card name on the field, you will see a IP address on the field. Ensure that that is the same as you have set before (i.e. 192.168.0.3). If it is not so, please repeat step 12. Click OK to close the program.
Tele Eye III+ Network Camera Installation Guide Page 27 IP Address Setup for Windows NT/2000/XP The follow procedures will set your Ethernet Card IP address manually for your local LAN purpose. Note that these procedures will NOT affect your PC to get on the Internet. If you discover that you cannot be able to access to the Internet after applying the settings, you have to undo the settings or re-install the software provided by your ISP and retry the steps again.
Tele Eye III+ Network Camera Installation Guide Page 28 Step 4: Enter an IP address, subnet mask and Default gateway. Step 5: Enter the Preferred and Alternate DNS server, if necessary. Step 6: Click OK to activate the new IP. Step 7: You have to confirm the IP address has been correctly set on your computer. On your windows, click start > run, type “cmd” at Open field and pressed OK button, then type “ipconfig” on the DOS prompt, you will see a IP set on your computer.
Tele Eye III+ Network Camera Installation Guide Page 29 SECTION B SPECIFICATIONS MODEL Type Minimum Illumination Electronic shutter Back Light Compensation White Balance Resolution Video Output Mounting Network No. of Concurrent Users Web Server sureLINK RS - 485 PCMCIA Event Action External Input Channel Max. Rating Voltage Max. Rating Ambient Temperature Relative Humidity WxDxH Net Weight Specifications NF610 IMAGE SENSOR 1/3" CCD, 16M colour, interlace 1.0 Lux at F/1.
