Notice: Signal Communications Limited reserves the right to make improvements to the products described in this manual at any time and without notice, This manual is copyrighted. All rights are reserved. This manual may not be copied, reproduced or translated in whole or part without prior consent from Signal Communications Limited. Third party trademarks are the properties of their respective holders. Copyright (c) 1995-98 Signal Communications Limited. All rights reserved. Version 1.
FCC Statement on Class B WARNING Changes or modifications to this unit net expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Installation and location hints 1. Do not install the Camera Control Unit in a location near heat sources, such as radiators or air-ducts, or in place subject to direct sunlight. 2. To prevent overheating, never cover the unit with cloth and never install in ill ventilated and narrow place. 3. Do not expose the unit to rain or place in an excessive moisture or dust environment. Do take immediate action if ever the unit do become wet. Turn off and refer servicing to qualified service personnel.
Table of Contents INTRODUCTIONS Features Standard packages INSTALLING Camera Control Unit ‘What you need Front panel and rear panel Hardware installation System diagram Wiring diagrams Connection for external devices Device ID setting INSTALLING Camera Control Software Software installation Start execution SPECIFICATIONS
Camera Control Unit User Guide Page 1 SECTION 1 INTRODUCTION Camera Control Unit provides remote and local control of the camera system. One, may, through the Eyelet Pvo camera control Software, controls the remote site camera to pan left/right, tilt up/down, zoom in/out, adjusts focus and aperture, and switches on/off washer and wiper of the camera house. Features + Manual controls : Pan/Tilt head : Pan, Auto pan, Tilt Zoom lens : Zoom, Focus, Aperture Camera house : Washer and Wiper.
Camera Control Unit User Guide Page 2 SECTION 2 INSTALLING REMOTE PTZ UNIT ‘What you need + IBM compatible PC. + Camera Control Unit. + Femaleness to Malleable shielded cable. AC-DC adapter : DC 1A. VAC Pan/tilt head with power supply. (optional) Zoom lens. (optional) VAC Camera house with power supply.
Camera Central Unit User Guide Hardware Installation Setup Procedures: Step 1: Step 2: Step 3: Step 4: Step 5: Connect one end of a RS232 cable to the computer. Afterward, plug the other end of the cable into the AUX port on the back of the Camera Control Unit. Tighten the retaining screws to ensure proper connection. Connect the zoom lens, camera house, pan tilt head to the 5-pin DIN plug, pin metal plug and 6-pin metal plug respectively. Please refer to page 6.
Camera Control Unit User Guide ha System diagram This is the system diagram of a PC and the Camera control unit.
Camera Control Uni [Erk ‘Wiring diagram CL pr Augur CONTROL Device ID Selection u goon : Bit01234567 ZOOM LENS Zoom control Focus control Iris control CAMERA HOUSE Washer on/off Wiper en/off PAN/TILT HEAD ~ Pan left/right/auto Tilt up/down
Camera Control Unit User Guide Page 6 Connection for external devices This is an example of the connections between Camera Control Unit and external devices. Different brand name and model may be different. Please refer to the instruction manuals of the external devices for exact connections. Panel Mount LENS OUTPUT Terminal Block SOCKET 5 6.5Vde 10% Iris 3 To Zoom ®® Zoom Tp.
Camera Control Unit User Guide Page 8 SECTION 3 SOFTWARE INSTALLATION Software Installation Create a sub directory called Eyelet and copy all the files on the floppy disk of the Sitcom Eyelet Pro Camera Control Software to the hard disk. You may also execute the main program from the floppy disk. Start Execution To start the Camera Control Software, run the “Control EXE” from the floppy disk or type at the DOS prompt: .J The application program is shown below.
Camera Control Unit User Guide Page 9 SECTION 4 SPECIFICATIONS CONTROLS Type of control PANEL CONTROL and REMOTE CONTROL Pan controls AUTOMATIC or MANUAL LEFT/RIGHT Tilt control UP/DOWN delectable Input voltage Focus NEAR/FAR delectable Zoom STATEWIDE delectable Iris OPEN/CLOSE delectable Environmental controls Push on WHIPPERSNAPPER CONNECTIONS 9V DC 1A nominal Lens output voltage 6.