Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 SIGFOX Mini base station Installation Guide DISTRIBUTOR APPROVED: AUTHOR SIGN-OFF SIGNATURE #1 SIGN-OFF SIGNATURE #2 SIGN-OFF SIGNATURE #3 SIGN-OFF SIGNATURE #4 SIGN-OFF SIGNATURE #5 NOTICE: The contents of this document are proprietary of SIGFOX and shall not be disclosed, disseminated, copied, or used except for purposes expressly authorized in writing by SIGFOX. © Copyright SIGFOX.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Table of contents 1 Installation site recommendations............................................................................................ 4 3 Warning statements................................................................................................................... 6 2 4 5 6 7 8 9 10 11 12 13 14 15 Specifications...........................................................................................
Mini base station installation guide Version 0.0 0.1 0.2 Changes description Description Draft §3 Warning statements added Addition of Antenna requirements © Copyright SIGFOX. All rights reserved Author C.Cazeaux C.Cazeaux S. Barreiro Ref.: MAN/DPL/000 Rev.: 0.
Mini base station installation guide 1 Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 INSTALLATION SITE RECOMMENDATIONS SIGFOX SMBS-T series are multiband, low profile, small factor base stations intended for extension of the SIGFOX base station family. These series are dedicated for quiet radio environments with limited performance for capacity and blocking resistance. This gives a complementary solution for the SIGFOX network based on macro cell SBS-T base stations.
Mini base station installation guide 2 Ref.: MAN/DPL/000 Rev.: 0.
Mini base station installation guide 3 Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 WARNING STATEMENTS FCC warning statement This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Conformément à la règlementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inferieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique a l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.
Mini base station installation guide Base station Component SMBS-T Mounting accessories Internet connection Component Modem Ethernet cable POE Description Mini Station Mast mounting plate or Din rail plate Description ADSL modem or SAT modem + power cable Ethernet cable category 6 or 6a Index - Index RJ45 connector for Ethernet cable 3G key. Must be agreed by SIGFOX. Activated M2M SIM card POE Injector + power cable supply Connector USB 3G key POE injector Ref.: MAN/DPL/000 Rev.: 0.
Mini base station installation guide USB 3G key (if 3G coverage POE injector 5 3G key Activated M2M SIM card POE Injector + power cable supply - 4 Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 SIGFOX DISTRIBUTOR SIGFOX 1 1 1 CABLE ETHERNET POE The Ethernet cable must be a category 6 or 6a. The maximum length of the cable depends on its gauge. Gauge > AWG25: 100m maximum Gauge = AWG26: 50m maximum The shielding of the Ethernet cable should be SFTP or SSTP.
Mini base station installation guide 7 Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 DEL STATUS Green flash => Boot sequence. Orange flash => Connection to the SIGFOX CRA for backbone access Orange light => Backbone configuration KO.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Coaxial cable measurement This measure aims at checking the cable characteristics at 868MHz ETSI or 902MHz FCC and the quality of the installation. Type of measurements : VSWR Loss Length The main cable measures must not exceed the following: VSWR : < 1.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Key risks The list below gives the main hotspots during the antenna installation. Connector installation procedure must be strictly followed in order to avoid specific problems VSWR on cables and to maximize the efficiency and lifetime of connections. Specific attention must also be paid to ensure waterproofness and labeling.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Top Down 11 WATERPROOFNESS Coaxial cable, connectors, and overall cables, performance and lifetime strongly depend on waterproofness level.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 Then, the pipe for the Ethernet cable must be waterproofed with self-vulcanizing scotch-seal (rubber mastic tape). 12 EARTHING THE BASE STATION In order to protect the station, it must be earthed with a G/Y 6mm2 wire (or AWG9). © Copyright SIGFOX.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 First you need to insert a grower washer or a lock washer and a grounding lug into a hexagon socket screw M4x10. And then you must screw it into the hole provided for this purpose on the side of the station. The correct tightening torque is of 2.2 N.m. If needed, you can bend the lug to ease the insertion of the wire.
Mini base station installation guide Ref.: MAN/DPL/000 Rev.: 0.2 Date:03/05/2016 ADSL connectivity checks : DSL and internet lights must be green (depends on the material) RF Tests An RF transmitter (key App) has been shipped with the Equipment. Press the transmitter button to switch it on, until the light becomes green. When it does get green stop moving and wait until the signal is received on the backend. Press again to switch the transmitter off.