User Operating Manual USER OPERATING MANUAL RADIO Manufactured by, Senao Neworks.
User Operating Manual MANUFACTURER SENAO NETWORKS MANUFACTURER’S ADDRESS NO. 528 Fushing 3rd, Hwa-Ya tech. Park Kueishan, Tao Yuan 333, Taiwan FACTORY NAME SENAO NETWORKS FACTORY ADDRESS NO. 528 Fushing 3rd, Hwa-Ya tech. Park Kueishan, Tao Yuan 333, Taiwan VERSION 2.
User Operating Manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User Operating Manual Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3.
User Operating Manual Table of Contents Safety precautions: ............................................................................................................................. 7 1.1 ODU ................................................................................................................................................... 8 Description ..............................................................................................................................................
User Operating Manual 1.7.1 Administration ..................................................................................................................... 25 1.7.2 SNMP Settings ...................................................................................................................... 26 1.7.3 Backup/Restore Settings ...................................................................................................... 27 1.7.4 Auto reboot settings ...........................................
User Operating Manual Safety precautions: Prior to connecting cables to the ODU, the protective earth terminal (screw) of the ODU must be connected to an external protective ground conductor or to a grounded mast. Only a qualified person using the proper safety equipment should climb the antenna mast. Only trained professional installers should be used when installing or dismantling ODUs and masts. Do not use product near water (i.e. wet basement, bathtub, sink or near a swimming pool, etc.
User Operating Manual 1.1 ODU Description Figure 1: Radio (SMAC5700) Thank you for using SMAC5700. It is a powerful, enhanced, enterprise scale product with functions Outdoor Base and Outdoor Subscriber. SMAC5700 uses the latest wireless technology 802.11n standard. It has faster transmit/receive wireless speed. SMAC5700 gives you a great advantage to save your time and cost to expend your network. It is also compatible with 802.11a.
User Operating Manual SMAC5700 is easily to install almost anywhere with Power over Ethernet for quick indoor installation and regular Power by Adapter. SMAC5700 can manage power level control, Narrow bandwidth selection, Traffic shaping and Real-time RSSI indicator. SMAC5700 is fully support of security encryption including Wi-Fi Protected Access (WPA2-PSK), 128 bit - AES Encryption and IEEE 802.1x with RADIUS. Technical Specification PRODUCT MODELS SMAC5700 SMAC 5700 Base station unit, 200 Mbps, 5.
User Operating Manual LED INDICATION LATENCY MCS6 / MCS14 -71 MCS7 / MCS15 -70 Ethernet status and wireless signal strength indication < 10 m.
User Operating Manual POWER CHORD POE Fuse Rating 6A 250V, 50 Hz 3 Pin Indian type IS:1293 2 Amp (2A, 250V), which is used in the location F, and F1. SURGE PROTECTION Inbuilt Ethernet Surge Protection ENVIRONMENTAL SPECS OPERATING, STORAGE HUMIDITY, IP RATING TEMPERATURE -15oC to 60oC 0% - 90%, (non-condensing) o o -15 C to 80 C IP 67 MECHANICAL SPECS DIMENSIONS DIMENSIONS (PACKED) (UNPACKED) 14.6 x 9.25 x 8.07 in 6.7x 10.2 x 3.
User Operating Manual The default operating mode is Outdoor Base for AP hardware and Outdoor Subscriber for SU hardware. Device will not assign an IP address to the computer/notebook. Therefore, follow the steps to assign an IP address to your Ethernet card. 1.3.1 Assign a Static IP In order to configure SMAC5700, please follow the instruction below: 1. In the Control Panel, double click Network Connections and then double click on the connection of your Network Interface Card (NIC).
User Operating Manual 2. Enter IP 192.168.1.1 into you address filter. If you have changed the SMAC5700 LAN IP address, make sure you enter the correct IP Address. 3. After connected to the SMAC5700 successfully, browser will pop out a Windows Security window. Please enter the correct Username and Password. 4. The default Username and Password are both admin. If you have changed the Username and Password, please enter your own Username and Password. Password length should be minimum 8 and maximum 16. 1.
User Operating Manual If any configuration changes has been made by the user the Save/Reload button will appear in Red color unless clicking the Save& Apply button. You cannot cancel the specific settings. You can only compile all the settings or revert to the previous settings. 1.4.2 Main Click on the Main link under the Status drop-down menu or click Home from the top-right of the webpage. The status that is displayed corresponds with the operating mode that is selected.
User Operating Manual This will be shown in Outdoor Base only 1.4.4 System Log Click on the System Log link under the Status drop-down menu. The device automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. 1.4.5 Connection Status Click on the Connection Status link under the Status drop-down menu.
User Operating Manual This will be shown in Outdoor Subscriber mode only. 1.5 System 1.5.1 Switching Operation Mode The SMAC5700 supports operation modes: Outdoor Base, Outdoor Subscriber. In order to switching between the operating modes, please go to System -> click Operation mode. Operation Mode: Select an operation mode via Radio Button. Click Save & Apply to confirm the changes. Accept does not compile the changes, you must go to Status -> Save/Load to apply the new settings. 1.5.
User Operating Manual IP Network Setting Select Radio button for Obtain an IP address automatically or Specify an IP address. IP Address Specify LAN port IP address. IP Subnet Mask Specify Subnet Mask. Default Gateway Specify Default Gateway Primary DNS Specify Primary DNS Secondary DNS Specify Secondary DNS Accept / Cancel Press Accept to confirm the changes or Cancel to return previous settings.
User Operating Manual The moment you click “Accept “the changes will take effect immediately, there is no need to save/reload. 1.5.4 Location Go to System -> Location to configure the customer name, customer location, customer email ID, customer mobile number & Link ID. 1.5.5 Spanning Tree Settings Go to System -> Spanning Tree settings to enable the spanning tree option and configure the STP parameters like hello time, Max Age, Forward Delay & Priority.
User Operating Manual Accept does not compile the changes, you must go to Status -> Save/Load to apply the new settings. 1.5.6 Service Settings Go to System -> Service settings to enable/disable the HTTPS/HTTP,SSH/TELNET options. Also upload the certificate for safety login through HTTPS. The moment you click “Accept “the changes will take effect immediately, there is no need to save/reload 1.6 Wireless Configuration This section will guide you through all the wireless settings.
User Operating Manual Under Wireless Click wireless Network Wireless Mode The wireless mode supports 802.11a/n mixed modes. It is compatible with the most common known wireless band. Channel HT Mode The default channel bandwidth is 20 MHz. The larger channel can provide better transmit quality and speed. 40 MHz options also available Extension Channel Specify the upper channel or lower channel selection. It may influence the Auto channel function Channel / Frequency Specify the channel/frequency.
User Operating Manual Wireless Mode The wireless mode supports 802.11a/n mixed modes. It is compatible with the most common known wireless band. Channel HT Mode Automatically detect the change when changed on Outdoor base Channel / Frequency Automatically detect the change when changed on Outdoor base Accept / Cancel Press Accept to confirm the changes or Cancel to return previous settings. Current Profile Configure the SSID, it can help to divide group of clients to access the network .
User Operating Manual Security Mode Select Enabled from the drop down list to begin the configuration. Encryption Advanced Encryption System. Passphrase Specify the security password. Passphrase Length 64 Hexadecimal characters password length.
User Operating Manual Security Mode Select WPA2-PSK from the drop down list to begin the configuration. Encryption Select AES for Encryption type. Passphrase Specify the security password. Passphrase Length 64 Hexadecimal characters password length.(minimum 8 characters) 1.6.3 Wireless MAC Filter Wireless MAC Filters is used to Allow or Deny wireless clients, by their MAC addresses, accessing the Network. You can manually add a MAC address to restrict the permission to access SMAC5700.
User Operating Manual 1.6.4 Wireless Advanced Settings Under Wireless Click Wireless Advanced Settings Data Rate Select Data Rate from the drop down list. Data rate will affect the efficiency of the throughput. If the data rate is set to a small number, the lower through will get but it can transmit to longer distance. Transmit Power Select Transmit Power to increase or decrease Transmit Power. Higher transmit power will sometimes cause unable to connect to the network.
User Operating Manual Short GI Short GI is improved of 802.11n and 802.11a/g. It can increase 10% of the internet speed during the data transmission. For example, the 802.11a/g’s GI is 800us; the short GI will be 400us. Aggregation Aggregation is to merge the typical size of data’s header to one data. It is useful for the small size but larger amount packets. Wireless Traffic Shaping Place a Check to enable Wireless Traffic Shaping function.
User Operating Manual Password Specify a Password for logging in Admin telnet / WEB as well as User Confirm Password Re-enter the Password for confirmation. Password length should be minimum 8 and maximum 16. Save/Apply / Cancel Press Save/Apply to apply the changes or Cancel to return previous settings. Press Save/Apply will change the setting immediately. It will not be able to undo the action. 1.7.2 SNMP Settings Click on the SNMP Settings link under the Management menu.
User Operating Manual Enable/Disable Select the Radio button to Enable or Disable SNMP function. Contact Specify the contact details of the device. Location Specify the location of the device. Community Name(Read only) Specify the password for access the SNMP community for read only access. By default its public; better keep it in default password. Community Name(Read/Write) User cant able to change the default SNMP Read/Write password.
User Operating Manual Save A Copy of Current Settings Click on Backup to save current configured settings. Restore Saved Settings from a File SMAC5700 can restore a previous setting that has been saved. Click on Browse to select the file and Restore. 1.7.4 Auto reboot settings Click on the Auto reboot setting link under the Management menu for auto rebooting the radio. 1.7.5 Firmware Upgrade Click on the Firmware Upgrade link under the Management menu.
User Operating Manual Upgrade process may take few minutes (approximate 3 minutes); please do not power off the device and it may cause the device crashed or unusable. SMAC5700 will restart automatically once the upgrade is completed. 1.7.6 Firmware Upgrade Settings Click on the Firmware Upgrade Settings link under the Management menu. This page is used to upgrade the firmware from remote. Latest firmware can be uploaded in server and connected devices can upgrade automatically when reboots. 1.7.
User Operating Manual Manually Set Date and Time Manually setup the date and time. Automatically Get Date and Time Specify the Time Zone from the drop down list and Place a Check to specify the IP address of the NTP Server manually or uses default NTP Server. Save/Apply / Cancel Press Save/Apply to apply the changes or Cancel to return previous settings. Press Save/Apply will change the setting immediately. It will not be able to undo the action. 1.7.
User Operating Manual Syslog Select Enable or Disable Syslog function from the drop down list. Log Server IP Address Specify the Log Server IP address. Local Log Select Enable or Disable Local Log service. Save/Apply / Cancel Press Save/Apply to apply the changes or Cancel to return previous settings. Press Save/Apply will change the setting immediately. It will not be able to undo the action. 1.7.9 Diagnostics Click on the Diagnostics link under the Management menu.
User Operating Manual 1.8.1 Reset Click on the Reset link under the Management menu. This page is used to reboot & reset the device to factory default. We can restore the factory setting with retain the IP setting, hence IP reachability will be available & all other parameters will go to factory settings. 1.9 LED Indication LED indication in Outdoor Subscriber (SU) mode and LED blinking format is given below.
