Sierra Monitor Corporation.
Revision History: No. Version Description Date 1 V1.0 Initial Version 2015.01.17 2 V1.1 Add DIP Switch explain 2015.01.25 3 4 V1.2 V1.3 Add some pictures to function Change some pictures to function 2015.02.01 2015.02.04 5 V1.4 2016.07.19 6 V1.5 7 V1.6 Statement SMC is the manufacturer to the device Require professionally install antennas and use antennas specified by the manufacturer Update the LTE 2/ 16 2016.08.03 2019.07.
Table of Contents 1. Foreword ................................................................................................................................ 4 1.1 Copyright Notice.........................................................................................................................4 1.2 Notes ..........................................................................................................................................4 1.3 Statement ...........................................
1. Foreword 1.1 Copyright Notice While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, SMC assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
The FPA‐C41should be installed, debugged and maintained by professional people. The outside antennas are not permitted to be installed or to be changed by non‐professional people. To run the device normally, only specify antennas are approved to be assembled together by professional people. Unit shall be used with indoor‐use antenna only. No antenna for this unit can be installed outdoor. 1.6 Safety Instructions Keep and comply with all operation instructions, warnings, and information.
Please power off before cleaning the device. Do not use spray detergent. Clean with a damp cloth. Do not try cleaning exposed electronic components unless with a dust collector. Support for special fault: Power off and contact technical support personnel of SMC in case of the following faults: The device is damaged. The temperature is excessively high. Fault is still not solved after the operation according to the manual.
2. Overview 2.1 Introduction Thank you for choosing SMC. It is our commitment to provide our valued customers with the embedded devices equipped with the state‐of‐the‐art technology and the best product services. SMC’s M2M products are based on the most advanced ARM and Intel Atom processors and have low‐power consumption and high integration. The products are designed for applications of M2M in industrials, medicals, financial, retail, vehicle, and transportations etc. 2.
2xLED for UART(RXD and TXD) LED 1xLED for power 1xLED for state of error 1xLED for state of SS Software Power Mechanical Environment Condition RTC Supported, separately RTC chip, power for super capacitor Control Button of Restored to Default setting GPIO 4XGPIO (Optional) OS WinCE or Linux Applications Provide SDK Input Wide Range (12-24V DC 0.3A), 3x3.
3. M2M Gateway‐FPA‐C41 Hardware Instructions 3.
3.2Interface Description 3.2.1 Power Interface PIN1 Power connector outlook Pin Description 1 Power input range 12‐24V 2 Ground 3 Shell ground 3.2.2 Ethernet Interface Standard RJ45 interface, supporting 10M/100M Full/Half Duplex, this is a standard RJ45 Ethernet port 3.2.3 RS232 or RS485 Connector Standard vertical 1x3x3.81mm male Terminal Block.
3 DGND 3.2.4 DIP Switch for select Bit 1 2 3 4 Description ON: have matched resistance of 120 ohm OFF: have no ON: have pull up resister of 510 ohm OFF: have no ON: have pull down resister of 510 ohm OFF: have no ON: select RS232 OFF: select RS485 Single Term Bias‐ Bias+ Select RS232 or RS485 3.2.5 DIP Switch for boot OPEN: Boot from NAND SHORT: Boot from SD/MMC 3.2.6LED PWR LED: lightindicatesystem power OK(main power up); off indicate system power turn off ERR LED: User can define by themself.
3.2.7 Micro SIM Card Push the SIM Card, and Push again, it can put in or put out. 3.2.8 DEBUG CONN, Pin header,1x4x2.0,TH, User can show the debug message and use keyboard input debug command. It’s TTL level, we need a Uart‐debug board when we use it. PIN1 Pin 1 Description 2 TTL_TXD 3 TTL_RXD 4 DGND 3.3V 3.2.9 Renew button Renew button: long press this button will restore the factory setting, the long press time can be setting by user 3.2.
4. Tips Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with the sign of “explosive” should not be disposed like household waste but delivered to specialized electrical & electronic waste recycling/disposal center.
FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
économique au Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Technical Support Please call us for any technical support needs related to the FieldSercer Product. Sierra Monitor Corporation 1991 Tarob Court Milpitas, CA 95035 Website: www.sierramonitor.com U.S. Support Information: +1 408 262‐6611 +1 800 717‐4377 Email: support@sierramonitor.com EMEA Support Information: +44 2033 1813 41 Email: support.emea@sierramonitor.com Manufacturer: ChengDu Vantron Technology., LTD No.