Configuring the operating system 6.10 Enabling PROFINET IO Procedure Proceed as follows: 1. If you wish the HMI device to load the PROFIsafe address set in the Control Panel, enter a value between 1 and 65,534 in the "Address:" text box. 2. If you wish the HMI device to load the PROFIsafe address set in the project, enter a value between the invalid PROFIsafe address 65,535 in the "Address:" text box. Result The PROFIsafe address is set. 6.
Configuring the operating system 6.10 Enabling PROFINET IO ④ MAC address of the LAN interface ⑤ MAC address of the WLAN interface Procedure 1. To enable PROFINET IO direct keys, select the "PROFINET IO enabled" check box. 2. Select the communications link. Note Select "LAN" for service purposes only. If you select "LAN", the HMI device is connected directly to the network via the RJ45 interface.
Configuring the operating system 6.11 Configuring network operation 6.11 Configuring network operation 6.11.1 Overview of network operation Introduction You connect the HMI device to a PROFINET network.
Configuring the operating system 6.11 Configuring network operation Printing via a network printer The HMI device's operating system does not support line by line alarm logging via a network printer. All other printing functions, for example hardcopy or logs are available without restriction via the network. Preparation Before beginning the configuration, request the following network parameters from your network administrator.
Configuring the operating system 6.11 Configuring network operation ① Device name of the HMI device ② Description for the HMI device (optional) Note To activate the network functions, enter a unique device name in the Device name text box. Procedure Proceed as follows: 1. Enter the device name for the HMI device in the "Device name:" text box. 2. If necessary, enter a description for the HMI device in the "Device description:" text box. 3. Confirm your entries. The dialog closes.
Configuring the operating system 6.11 Configuring network operation Requirements for changing WLAN or LAN connection settings You have opened the following display by touching the "Network and Dial-Up Connections" icon. You can enter the connection parameters for the WLAN and LAN connection. The parameterization is identical. Procedure for setting the connection parameters The following procedure shows how to set the connection parameters using the WLAN connection. Proceed as follows: 1.
Configuring the operating system 6.11 Configuring network operation 1. Enter the appropriate addresses. 2. Confirm your entries. The dialog closes. 3. Close the "Network and Dial-Up Connections" display. The Control Panel is displayed again. Result The WLAN / LAN connection parameters for the HMI device have been set. See also Overview of network operation (Page 167) 6.11.4 Changing the logon data Introduction In order to access certain network resources you need to log on to the network as a user.
Configuring the operating system 6.11 Configuring network operation 4. Confirm your entries. The dialog closes. Result The logon data has now been set. See also Overview of network operation (Page 167) 6.11.5 Changing e-mail settings Requirements You have opened the "WinCC flexible Internet Settings" dialog with the "WinCC Internet Settings" icon.
Configuring the operating system 6.12 Changing internet settings 1. Specify the SMTP server. – Select the "Use the default of the project file" option button if you want to use the SMTP server configured in the project. – Clear the "Use the default of the project file" option button if you do not want to use the SMTP server configured in the project. Specify the required SMTP server. 2. Enter the name for the sender in the "Sender" text box. 3.
Configuring the operating system 6.12 Changing internet settings Note Do not change the settings in the "User Agent" box. Procedure Proceed as follows: 1. Enter the homepage for the Internet browser in the "Start Page" text box. 2. Enter the address of the required search engine in the "Search Page" text box. 3. Enter the required cache memory size in the "Cache" text box. 4. If you want to delete the cache memory, press the "Clear Cache" button. 5.
Configuring the operating system 6.12 Changing internet settings 2. If you are using a proxy server, in the "Network" group, select the "Access the Internet using a proxy server" check box. Specify the address of the proxy server and the interface. 3. If you want to bypass the proxy server for local addresses, select the "Bypass proxy server for local addresses" check box. 4. Confirm your entries. The dialog closes. 6.12.
Configuring the operating system 6.12 Changing internet settings Cookies will not be stored. – "Prompt" Cookies will be stored on request. 2. If you want allow cookies which are restricted to a single session, select the "Always allow session cookies" check box. 3. Change to the "Advanced" tab. 1. Activate the required encryption protocol. 2. Confirm your entries. The dialog closes. Result The safety settings have now been set. 6.12.
Configuring the operating system 6.13 Backing up and restoring with an external memory medium Procedure Proceed as follows: 1. Select the type of certificate from the selection box: – "Trusted Authorities" – "My Certificates" – "Other Certificates" 2. If required, start the importing process with the "Import.." button. A dialog with source details will open. 3. If required, delete the certificate. – Mark the desired certificate. – Delete the selected certificate using the "Remove" button. 4. The "View..
Configuring the operating system 6.13 Backing up and restoring with an external memory medium ● Memory card ● USB memory stick CAUTION IP65 degree of protection not fulfilled To insert or remove the memory card, you must open the HMI device's connection compartment. If the connection bay is open, degree of protection IP 65 is not fulfilled. It is preferable to back up onto a USB memory stick. Requirements for backup ● The current project and all other applications are closed, except Control Panel.
Configuring the operating system 6.13 Backing up and restoring with an external memory medium – Data is already stored on the external memory. 2. Follow the instructions of the HMI device. The following messages are displayed in sequence during backup: – "Checking Registry" – "Backup Progress" – "Saving CE-Image" A progress bar shows the status of the backup process. If backup was successful, the following message is displayed: "Backup successfully completed. Press OK and remove your storage card." 3.
Configuring the operating system 6.13 Backing up and restoring with an external memory medium The HMI device checks the external memory. The HMI device issues messages in the following situations: – The external memory is not available or is defective: Acknowledge the displayed messages. The Control Panel is displayed again. Replace the external memory. – More than one external memory with valid backup is available: Remove all external memories with backups that are not needed.
Configuring the operating system 6.14 Displaying battery status See also Displaying information about the HMI device (Page 157) Using a memory card with the HMI device (Page 113) 6.14 Displaying battery status Introduction You can check the charging status and the temperature of the main battery and the bridging battery.
Configuring the operating system 6.15 Activate memory management Procedure Proceed as follows: 1. Update the display if required by pressing the "Update" button. 2. Close the dialog. 6.15 Activate memory management Memory management Provided the memory management is activated, the HMI device will automatically close the project if the memory needs reorganizing during an active project. The project is shut down and the HMI device will display a message. You have to restart the project.
Configuring the operating system 6.15 Activate memory management Procedure Proceed as follows: 1. In order to start memory management, select the check box. 2. Confirm your entries. The dialog closes. Result Memory management is activated.
Commissioning the HMI device 7.
Commissioning the HMI device 7.2 Operating modes Note If the project contains effective ranges, you must perform an acceptance test for the effective ranges and transponders. You can only start the project on the HMI device once the acceptance test is complete. ● If necessary: Testing zones See also Mounting the charging station (Page 66) Connection of the charging station to the power supply (Page 70) Programming the data channel (Page 160) Acceptance of the system (Page 196) 7.
Commissioning the HMI device 7.3 Using existing projects Note Emergency stop button active In "Offline" mode, the emergency stop button is active when the following requirements are met: • The HMI device is in an area with sufficient WLAN coverage. • The HMI device is integrated in the safety program of the CPU. "Online" operating mode In this mode, the HMI device and PLC communicate. You can operate the plant on the HMI device according to your system configuration.
Commissioning the HMI device 7.4 Data transmission options ● Mobile Panel 277 Carry out an HMI device switch in WinCC flexible.
Commissioning the HMI device 7.5 Preparing and backing up a project Type License key transferring or transferring back Data channel Mobile Panel 277 Wireless Ethernet Yes USB Yes Ethernet Yes 7.5 Preparing and backing up a project 7.5.1 Overview Introduction In order to operate the system with the HMI device, you must transfer the WinCC flexible project to the HMI device.
Commissioning the HMI device 7.5 Preparing and backing up a project 7.5.2 Transfer 7.5.2.1 Overview Transfer At the end of the configuration phase, transfer the executable project from the configuring PC to the HMI device. You can start the "Transfer" mode manually or automatically on the HMI device. Transferred data is written directly to the internal flash memory on the HMI device. For the transfer, you use a data channel which you have to configure before starting a transfer.
Commissioning the HMI device 7.5 Preparing and backing up a project Procedure Proceed as follows: 1. On the configuring PC, select the "Transfer settings" command in the menu "Project > Transfer" in WinCC flexible. The "Select devices for transfer" dialog opens. 2. Select the HMI device in the left area of the dialog. 3. Select the type of connection between the HMI device and the configuring PC. 4. Set the connection parameters. 5. Set the transfer parameters in the right area of the dialog. 6.
Commissioning the HMI device 7.5 Preparing and backing up a project NOTICE Undesired system responses If automatic transfer has been selected on the HMI device and a transfer is then initiated on the configuring PC, the current project is automatically terminated following a prompt. The HMI device then automatically switches to "Transfer" mode. The transfer mode can trigger undesired responses in the system.
Commissioning the HMI device 7.5 Preparing and backing up a project the connection is not available or is defective, an error message is displayed on the configuring PC. Result When the transfer is completed successfully, the project can be found on the HMI device. The transferred project is then started automatically. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) 7.5.2.
Commissioning the HMI device 7.5 Preparing and backing up a project Result After successful backtransfer, the project is opened on the configuring PC in WinCC flexible. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) 7.5.3 Testing a project Introduction There are two options to test a project: ● Test the project on the configuring PC You can test a project at a configuring PC, using a simulator.
Commissioning the HMI device 7.5 Preparing and backing up a project Note Test without effective ranges Perform the test without effective ranges. A system acceptance test must be performed as soon as you have configured effective ranges in your project. The effective ranges and assigned transponders will be tested as part of the acceptance test. Test the effective ranges separately. Requirements for offline testing ● The project has been transferred to the HMI device ● The HMI device is in "Offline" mode.
Commissioning the HMI device 7.5 Preparing and backing up a project 7.5.4 Acceptance of the system 7.5.4.1 Overview Introduction The acceptance of the system includes the following areas: ● Configuring the F CPU and fail-safe I/O ● Safety program ● Effective ranges and transponders Acceptance steps that you must execute in order to operate the Mobile Panel 277F IWLAN HMI device in a system with effective ranges are described in detail in these operating instructions.
Commissioning the HMI device 7.5 Preparing and backing up a project Acceptance if there are changes If you change the configuration of transponders and effective ranges in the system, then you must adjust the configuration. Then you must accept the effective ranges and transponders again. Requirements ● In the project: – Effective ranges and transponders must be configured in the project. – The project has been transferred to the HMI device.
Commissioning the HMI device 7.5 Preparing and backing up a project To the left you will see the list with the names of all configured effective ranges. 3. In the "Effective ranges" list highlight the first effective range that you want to verify. In the "Transponder" list on the right, the names of the transponders are displayed that are assigned to the effective range in the project. 4. Go to the first transponder that you want to verify in the "Transponder" list. 5.
Commissioning the HMI device 7.5 Preparing and backing up a project 13.Open the project in WinCC flexible ES. 14.Enter the checksum in the "Effective ranges" editor. 15.Transfer the project to the HMI device again. Result The HMI device can now be used for operating and monitoring the system. 7.5.4.
Commissioning the HMI device 7.5 Preparing and backing up a project 7.5.5 Testing zones If zones are present in the system, you need to test whether the HMI device is detecting them.
Commissioning the HMI device 7.5 Preparing and backing up a project General information NOTICE Resetting to factory defaults required If a complete restore operation is interrupted due to power failure on the HMI device, the operating system of the HMI device may be deleted! In this case, you have to reset the HMI device to its factory settings.
Commissioning the HMI device 7.5 Preparing and backing up a project A status view opens to indicate the progress of the operation. Result The system outputs a message when the backup is completed. The relevant data is now backed up on the configuring PC. Procedure for restoring Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication settings" dialog box opens. 2. Select the type of HMI device. 3.
Commissioning the HMI device 7.5 Preparing and backing up a project Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 200) 7.5.6.3 Backup and restore using ProSave Requirements ● The HMI device is connected to a PC on which ProSave is installed ● The data channel is programmed on the HMI device Procedure for backup Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3.
Commissioning the HMI device 7.5 Preparing and backing up a project You can see the HMI device for which the backup file was created and the type of backup data the file contains. 6. Set "Transfer" mode on the HMI device. If automatic transfer has been selected on the HMI device, following a prompt the HMI device automatically switches to "Transfer" mode when a restore operation is initiated. 7. Start the restore operation in ProSave on the PC with "Start Restore".
Commissioning the HMI device 7.5 Preparing and backing up a project General information NOTICE Resetting to factory defaults required If the update of the HMI device image is interrupted due to a power failure on the HMI device, the operating system of the HMI device may be deleted. In this case, you have to reset the HMI device to its factory settings. NOTICE Data loss All data on the HMI device, such as the project and passwords, will be deleted when you update the operating system.
Commissioning the HMI device 7.5 Preparing and backing up a project NOTICE Data channels When resetting to factory settings, all data channel parameters are reset. The transfer can only be started following reconfiguration of the data channels. Note You have to perform an operating system update with reset to factory settings if the HMI device does not yet have an operating system or if the operating system of the HMI device is corrupt.
Commissioning the HMI device 7.5 Preparing and backing up a project 10.Follow the instructions in WinCC flexible. During the operating system update a status view opens to indicate progress. Result A message is displayed when the operating system update is successfully completed. This operation has deleted the project data from the HMI device. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 204) 7.5.7.
Commissioning the HMI device 7.5 Preparing and backing up a project Result A message is displayed when the operating system update is successfully completed. This operation has deleted the project data from the HMI device. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 204) 7.5.7.
Commissioning the HMI device 7.5 Preparing and backing up a project Note Possible address conflicts with incorrect IP address Do not use a dynamic IP configuration for "Reset factory settings". Define an IP address which the HMI device is going to receive from the configuration station during the update process. If the HMI device has already been used with WinCC flexible or ProSave you can use the existing IP address for "Reset factory settings". 1. Confirm your entries. 2.
Commissioning the HMI device 7.5 Preparing and backing up a project This operation has deleted the project data from the HMI device. The factory settings are reset. Note Calibrating the touch screen After the restore, you may have to re-calibrate the touch screen. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 204) 7.5.7.
Commissioning the HMI device 7.5 Preparing and backing up a project Note Possible address conflicts with incorrect IP address Do not use a dynamic IP configuration for "Reset factory settings". Define an IP address which the HMI device is going to receive from the configuration station during the update process. If the HMI device has already been used with WinCC flexible or ProSave you can use the existing IP address for "Reset factory settings". 1. Change to the "OS Update" tab. 2.
Commissioning the HMI device 7.5 Preparing and backing up a project Result A message is displayed when the operating system update is successfully completed. This operation has deleted the project data from the HMI device. The factory settings are reset. Note Calibrating the touch screen After the restore, you may have to re-calibrate the touch screen. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 204) 7.5.
Commissioning the HMI device 7.5 Preparing and backing up a project Procedure for installing an option Proceed as follows: 1. On the configuring PC, select the "Communication settings" command in the menu "Project > Transfer" in WinCC flexible. The "Communication settings" dialog box opens. 2. Select the type of HMI device. 3. Select the type of connection between the HMI device and the configuring PC. 4. Set the connection parameters. 5. Close the dialog with "OK". 6.
Commissioning the HMI device 7.5 Preparing and backing up a project 10.Start the removal of the option in WinCC flexible on the configuring PC with the "<<" button. 11.Follow the instructions in WinCC flexible. A status display appears indicating the progress of the removal. Result The option has now been removed on the HMI device. See also Operating modes (Page 186) Data transmission options (Page 188) Programming the data channel (Page 160) Overview (Page 212) 7.5.8.
Commissioning the HMI device 7.5 Preparing and backing up a project Result The option has now been installed on the HMI device. Procedure for removing an option Proceed as follows: 1. From the Windows Start menu, start ProSave on the PC. 2. Select the HMI device type in the "General" tab. 3. Select the type of connection between the HMI device and the PC. 4. Set the connection parameters. 5. Select the "Options" tab. 6. Press the "Device status" button to update the display. 7.
Commissioning the HMI device 7.5 Preparing and backing up a project You can also transfer back the license key from the HMI device to the storage location. Note You only transfer license keys with the Automation License Manager or WinCC flexible. 7.5.9.
Commissioning the HMI device 7.5 Preparing and backing up a project Result The license key is transferred from the storage location to the HMI device. Procedure for transferring back a license key Proceed as follows: 1. Switch to "Transfer" mode on the HMI device. 2. When transferring back using WinCC flexible: Select the "License Keys" command in the menu "Project > Transfer". The Automation License Manager opens.
Fail-safe mode 8.1 8 Organizational measures The HMI device should only be operated in the system with a battery or in the charging station. To ensure fail-safe operation of the HMI device the organizational measures described below must be complied with. Storing the HMI device WARNING Non-functional emergency stop button If the HMI device is not integrated, the emergency stop button does not function.
Fail-safe mode 8.2 Switch-off behavior The following must be noted when working with the Mobile Panel 277F IWLAN: ● Pay attention to the "SAFE" LED. If the HMI device is integrated in fail-safe communication, the "SAFE" lights up and the emergency stop button is active. ● Pay attention to the "COM" LED. If you leave the area with sufficient WLAN coverage, the "COM" LED will flash. Communication between the HMI device and PLC is down. You can no longer operate the system with the HMI device.
Fail-safe mode 8.2 Switch-off behavior The emergency stop button is always active if there is PROFIsafe communication between HMI device and F CPU, i.e. if the HMI device is integrated in the PROFIsafe communication. If PROFIsafe communication is present the "SAFE" LED lights up. Shutdown Shutdown is triggered by the F CPU. The shutdown is specific to the effective range.
Fail-safe mode 8.3 Integrating the HMI device effective range 8.3 Trigger HMI device is outside of the effective range for less than 30 seconds Emergency stop Shutdown --- HMI device is outside of the effective range for longer than 30 seconds Emergency stop Shutdown Local rampdown HMI device is logged off from the effective range Emergency stop Global rampdown --- Integrating the HMI device Introduction During fail-safe operation, a safety program runs in the F CPU.
Fail-safe mode 8.4 Removing the HMI device Result The project start screen appears. The "SAFE" LED lights up. 8.4 Removing the HMI device Removing This concept refers to intentionally removing the HMI device from the safety program. You have the following options for removing the HMI device: ● Close the project. ● Press and hold the ON/OFF button for at least 4 seconds. After it has been removed, the HMI device switches off.
Fail-safe mode 8.5 Logging onto and off from the effective range PROFIsafe communication is terminated. The HMI device is removed from the safety program of the F CPU. The project is terminated. If you have pressed the ON/OFF button, the HMI device switches off. Removal in the event of a communication error In the event of a communication error, the F CPU removes the HMI device and initiates a global rampdown. The "SAFE" LED on the HMI device goes out. The project is terminated. 8.
Fail-safe mode 8.5 Logging onto and off from the effective range The dialog closes. Result ● If the ID entered matches the ID configured for the effective range, the HMI device is logged onto the effective range. ● No other HMI device can log onto this effective range. The "RNG" LED lights up. ● You can use the enabling buttons to operate the machine in the effective range. ● The "Effective range name" operating element is displayed as follows: .
Fail-safe mode 8.6 "Override" mode Requirements for logging off ● The HMI device is logged onto the effective range. The "RNG" LED lights up. ● The "Effective range name" operating element is configured and displayed as follows: Procedure for logging off Before leaving the effective range or project, you must log off from the effective range. 1. Touch the "Effective range name" operating element. The "Effective range logoff" dialog box opens. 2. Confirm logging off with the "OK" button.
Fail-safe mode 8.6 "Override" mode "Override" mode must only be used in defined system zones that are secured by additional protective measures, such as a safety gate. The switch for activating "Override" mode must be inside the protective device, and in an effective range.
Fail-safe mode 8.6 "Override" mode ● The HMI device is logged onto the same effective range in which the override switch located. The "RNG" LED lights up. NOTICE If "Override" mode is activated and you leave the defined system area, "Override" mode will be automatically deactivated. You must reactivate the override switch when you return to the defined system area. Procedure for activating "Override" mode 1. Enter the protection zone. The protective device is thereby activated. 2.
Fail-safe mode 8.
Operating a project 9.1 9 Starting the project Requirements In order to switch on the Mobile Panel 277F IWLAN and start the project, the following requirements must be met: ● The batteries have been charged and inserted in the HMI device If the batteries are not available, place the HMI device in the charging station ● The project has been transferred to the HMI device.
Operating a project 9.2 Error cases 1. If one of the 3 WLAN networks is available when the HMI device is started, the HMI device connects automatically. The "COM" LED will flash as long as the WLAN connection is established. The configured sequence of SSIDs determines the order in which the HMI device will attempt to connect to the WLAN networks. 2. If the HMI device cannot establish a connection with any of the 3 configured WLAN networks, the HMI device will attempt to connect to other WLAN networks.
Operating a project 9.2 Error cases Leaving the HMI device logged onto the effective range CAUTION Shutdown Under no circumstances should the effective range be left without an HMI device while the HMI device is logged onto the effective range. If the HMI device is in a state where it is constantly ready for operation, the battery will lose its charge. A flat battery will result in a communication error. The F CPU initiates a shutdown. • Log the HMI device off from the effective range.
Operating a project 9.3 Direct keys 9.3 Direct keys Introduction Direct keys on the HMI device are used to set bits in the I/O area of a SIMATIC S7. Direct keys enable operations with short reaction times, that are, for example, a jog mode requirement. NOTICE PLC stop Please note that leaving the WLAN area will cause the PROFINET IO device to fail and will therefore result in a PLC stop. Determine suitable programming measures in the PLC, in order to prevent a PLC stop.
Operating a project 9.4 Operator input options 9.4 Operator input options Once the project is transferred to the HMI device, current processes can be operated and monitored in the process control phase. You have the following options for operating the HMI device: ● Touch screen The HMI device is operated by means of the touch screen. The operating elements shown in the dialogs are touch-sensitive. Touch objects are basically operated in the same way as mechanical keys.
Operating a project 9.4 Operator input options Unintentional actions CAUTION Do not carry out several operations simultaneously. You may otherwise trigger unintentional actions. • With touch control: Always touch only one operating element on the screen • With key operation via an external keyboard: Do not press more than two keys simultaneously Observing the plant documentation Some operations with the project may require in-depth knowledge about the specific plant on the part of the operator.
Operating a project 9.5 Function keys The configuration engineer determines the appearance of a marked field, for example, line width and color for the focus. ● Invisible buttons By default, invisible buttons are not displayed as pressed when they are touched. No optical operation feedback is provided in this case. The configuration engineer may, however, configure invisible buttons so that their outline appears as lines when touched. This outline remains visible until you select another operating element.
Operating a project 9.6 Setting the project language CAUTION Unintentional actions In "Online" mode, simultaneous operation of more than two keys may cause unintentional actions in the plant. Do not press more than two keys simultaneously. 9.6 Setting the project language Introduction The HMI device supports multilingual projects. You must have configured a corresponding operating element which lets you change the language setting on the HMI device during runtime.
Operating a project 9.7 Input 9.7 Input 9.7.1 Overview Screen keyboard When you touch an operating element requiring entry on the HMI device touch screen, a screen keyboard appears. The screen keyboard is displayed in the following cases: ● An I/O field is selected for input ● A password must be entered for accessing a password-protected function The screen keyboard is automatically hidden again when input is complete.
Operating a project 9.7 Input – Alphanumerical values, for example digits and letters – Date/time 2. Enter the value. 3. Confirm your entry with 9.7.2 or discard your entry with the button . Entering and editing numerical values Numerical screen keyboard When you touch an operating element for numerical input on the HMI-device touch screen, the numerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete.
Operating a project 9.7 Input Limit value test of numerical values Tags can be assigned limit values. If you enter a value that lies outside of this limit, it will not be accepted, for example, 80 with a limit value of 78. In this case the HMI device will deliver a system alarm, if an alarm window is configured. The original value is displayed again. Decimal places for numerical values The configuration engineer can define the number of decimal places for a numerical text box.
Operating a project 9.7 Input 9.7.3 Entering and editing alphanumerical values Alphanumerical screen keyboard When you touch an operating element for numerical input on the HMI-device touch screen, the alphanumerical screen keyboard appears. This is the case, for example, for a text box. The screen keyboard is automatically hidden again when input is complete.
Operating a project 9.7 Input – The selected value is deleted when you enter the first character. Completely reenter the value. and keys to move the cursor within the current value. You can – Use the now edit the characters of the current value or add characters. key to delete the character to the left of the cursor. If the value is Use the selected, use this key to delete the selected part of the value. key deletes the character positioned to the right of the cursor.
Operating a project 9.8 Displaying infotext 9.7.5 Entering symbolic values Drop down list box Operating elements for entering symbolic values offer you a list from which you can select the input values. When you touch a symbolic I/O field on the HMI device touch screen, the following drop down list box opens. Figure 9-3 Symbolic I/O field after touch, example Procedure Proceed as follows: 1. Touch the required operating element. The drop down list box of the operating element opens.
Operating a project 9.8 Displaying infotext Figure 9-4 Infotext for an I/O field, example Opening infotext for operating elements 1. Touch the required operating element. key whether The screen keyboard opens. You can see from the appearance of the infotext has been configured for the operating element or the current screen. 2. Touch the key on the screen keyboard. The infotext for the operating element is displayed.
Operating a project 9.9 Device-specific displays 9.9 Device-specific displays 9.9.1 Displaying battery status Application The "Battery" object indicates the charging status of the main battery. Charge the battery in good time. Alternatively, change the main battery. Layout Symbol Color Meaning Charging status Green The battery is sufficiently charged. >20 % Yellow The battery is weak. The battery must be charged. Alternatively, insert a charged spare battery.
Operating a project 9.9 Device-specific displays Symbol Meaning Signal strength No wireless connection No signal Very poor wireless connection ≤20 % Poor wireless connection ≤40 % >20 % Wireless connection OK ≤60 % >40 % Good wireless connection ≤80 % >60 % Very good wireless connection >80 % Operation The "WLAN quality" object is purely for display purposes. You cannot operate the "WLAN quality" object. 9.9.
Operating a project 9.9 Device-specific displays Symbol Description Logon The HMI device is within the effective range shown. It is possible to log onto the effective range. The HMI device is not logged onto the effective range. The enabling button is not active. The HMI device is within the effective range shown and is logged onto the effective range. The HMI device is logged onto the effective range. Using the enabling buttons, safe operation in the effective range is possible .
Operating a project 9.9 Device-specific displays Symbol Meaning Quality The HMI device is in the middle of the effective range. >15 % The HMI device is at the limits of an effective 1% to 15% range. The HMI device is not within the effective range. 0% "Override" mode is active. The distance of the HMI device to the transponders is not evaluated. "Override" mode (Page 226) – The "Effective range name" object indicates which effective range this concerns.
Operating a project 9.9 Device-specific displays Symbol Meaning The HMI device is not inside any zone. Operation The "Zone name" object is purely for display purposes. You cannot operate the "Zone name" object. 9.9.6 Displaying zone quality Application The "Zone quality" object shows how close the HMI device is to the limits of a zone. Unlike with "WLAN quality", the HMI device does not measure signal strength.
Operating a project 9.10 Bar and gauge Operation The "Zone quality" object is purely for display purposes. You cannot operate the "Zone quality" object. 9.10 Bar and gauge Bar The bar is a dynamic display object. The bar displays a value from the PLC as a rectangular area.
Operating a project 9.11 Operating the slider control Layout The layout of the gauge depends on the configuration: ● A trailing pointer can display the maximum value reached so far on the scale. The trailing pointer is reset when the screen is reloaded ● The label on the scale can show the measured variable, for example boiler pressure and the physical unit, for example bar Operation The bar and the gauge are for display only. Both objects cannot be controlled by the operator. 9.
Operating a project 9.12 Operating the switch Procedure Proceed as follows: 1. Touch the slider of the desired slider control. 2. Move the slider to the required value. If a value display has been configured, you can check the exact value that has been set. 3. Release the slider. Result The set value is applied. 9.12 Operating the switch Introduction The switch is an operating element and display object with two predefined switching states, for example "On" and "Off".
Operating a project 9.13 Operating the trend view Procedure ● Switch with slider Proceed as follows: Move the slider to the other position or double-click the slider area ● Switch with text or graphic Proceed as follows: Touch the switch Result The switch changes its appearance. The associated value is switched. 9.13 Operating the trend view Trends Trends continuously display the current process data or process data from a log. Trend view Trends are displayed in the trend view.
Operating a project 9.13 Operating the trend view ③ Trend value in the value table Layout and operation The layout and operation of the trend view depends on the configuration.
Operating a project 9.14 Operating the Status Force Buttons Functions Scrolls back to the beginning of the trend recording. The start values of the trend recording are displayed there. Moves the ruler backwards (to the left) Moves the ruler forwards (to the right) Shows or hides the ruler. In addition, the configuration engineer can configure function keys or operating elements with which you can control trend views.
Operating a project 9.14 Operating the Status Force The figure shows the general layout of Status Force. A value can be monitored or controlled on every line. Figure 9-7 Status Force, example The configuration engineer specifies which columns appear in Status Force. The table shows the significance of all configurable columns. Column Functions "Connection" The PLC whose address ranges must be displayed.
Operating a project 9.14 Operating the Status Force 9.14.2 Operation Operator input options Status Force can be operated as follows: ● Change the column sequence ● Read the status values of the connected PLC ● Enter values and transfer them to the PLC Change column sequence Depending on the configuration, you can change the column sequence of Status Force. Proceed as follows: 1. Touch the column header which you wish to exchange with a different column header 2.
Operating a project 9.15 Operating the Sm@rtClient view 2. Once you have entered all of the desired values, touch the button. Result The values from the "Control value" column are transferred once to the PLC. 9.15 Operating the Sm@rtClient view 9.15.1 Overview Application The Sm@rtClient view enables you to monitor and remotely operate the current project of a remote HMI device. With the correct configuration, several equal priority HMI devices can access a remote HMI device.
Operating a project 9.15 Operating the Sm@rtClient view You can operate the project of the remote HMI device with the operator controls of your HMI device ● Operate keys from a local touch screen All the keys of the remote HMI device are displayed as buttons on the touch screen. You can also touch them to operate them ● Touch operation from a local HMI device using keys You operate the buttons in the usual manner. 9.15.
Operating a project 9.
Operating a project 9.16 Project security Central user administration using SIMATIC Logon Users, user groups and authorizations can be stored on a central server. If user administration cannot contact the server, an error message is displayed. If this is the case, you can only log on locally. Check whether additional information is available in your plant documentation.
Operating a project 9.16 Project security The users, passwords, group assignments and logoff times set up on the HMI device can be backed up and restored. This prevents you having to enter all of the data again on another HMI device. NOTICE The currently valid user data is overwritten in the following cases: • Depending on the transfer settings, when the project is transferred again • Upon restore of a backed-up project • Upon import of the user administration via an operating element.
Operating a project 9.16 Project security Simple user view If you are not logged on to the HMI device, the only entry contained in the simple user view is "". If you are logged on to the HMI device, the simple user view only displays the user name and user group. Extended user view The extended user view displays information about the users. The extended user view contains the following columns: ● Users ● Password ● Group ● Logoff time The passwords are encrypted by appearing as asterisks. 9.16.
Operating a project 9.
Operating a project 9.16 Project security Result After successful logon to the security system, you can execute password-protected functions on the HMI device for which you have authorizations. If you enter a wrong password, an error message is displayed when an alarm window has been configured. 9.16.4 User logoff Requirements You have logged into the security system of the HMI device.
Operating a project 9.16 Project security 1. Touch the "" entry in the user view. The following dialog opens: 1. Enter the desired user name and password. Touch the corresponding text box. The alphanumerical screen keyboard is displayed. 2. Touch the "OK" button. The following dialog opens: 1. Assign the user to a group. In order to do so, open the "Group" drop down list box by means of the and to scroll in the drop down list box. button. Select 2.
Operating a project 9.16 Project security Result The new user is created. 9.16.6 Changing user data Requirements You have opened a screen containing the user view. Which data you are allowed to change depends on your authorization: ● You are an administrator or a user with user management authorization.
Operating a project 9.17 Closing the project 9.16.7 Deleting users Requirements You have opened a screen containing the user view. To delete a user, you must be an administrator or have user management authorization. Note The "Admin" and "PLC_User" users exist by default. These users cannot be deleted. Procedure To delete a user, delete the user name entered. Result The user has been deleted and may no longer log onto the project. 9.17 Closing the project Procedure Proceed as follows: 1.
Operating alarms 10.1 10 Overview Alarms Alarms indicate events and states on the HMI device which have occurred in the system, in the process or on the HMI device itself. A status is reported when it is received. An alarm could trigger one of the following alarm events: ● Incoming ● Outgoing ● Acknowledge The configuration engineer defines which alarms must be acknowledged by the user.
Operating alarms 10.2 Recognizing pending alarms System alarms indicate states or events which occur on the HMI device ● SIMATIC diagnostic alarms SIMATIC diagnostic alarms show states and events of the SIMATIC S7 or SIMOTION PLCs ● User-specific alarm classes The properties of this alarm class must be defined in the configuration Please refer to your system documentation to check whether additional information on this subject is available there.
Operating alarms 10.3 Displaying alarms Figure 10-1 Alarm indicator with three pending alarms The alarm indicator flashes as long as alarms are pending for acknowledgment. The number displayed indicates the number of pending alarms. The configuration engineer can assign functions to be executed when the alarm indicator is operated. Usually, the alarm indicator is only used for error alarms.
Operating alarms 10.3 Displaying alarms Buttons Functions Acknowledge alarm. Select the next or previous alarm in the list. Scroll one page up or down. Extended alarm view 1R 7LPH 0RWRU WRR KRW 'DWH 6WDWXV . The buttons have the following functions: Buttons Functions Displaying infotext for an alarm. Process alarm. Acknowledge alarm.
Operating alarms 10.4 Display infotexts for an alarm Symbol Alarm class $ System The configuration engineer can change the symbols for the alarm classes. Please refer to your system documentation to check whether additional information on this subject is available there. Alarm window The alarm window is independent of the process screen. Depending on the configuration, the alarm window opens automatically as soon as a new alarm is pending for acknowledgment.
Operating alarms 10.6 Edit alarm Procedure Proceed as follows: 1. Touch the desired alarm in the alarm view or the alarm window. The alarm is selected. 2. Touch the button in the simple alarm view or in the extended alarm view. Alternative operation Depending on the configuration, you can also acknowledge an alarm with a function key. Result The alarm is acknowledged. If the alarm belongs to an alarm group, all the alarms of the associated group are acknowledged.
Operating recipes 11.1 11 Overview Introduction Recipes are used when different variants of a product are manufactured with the same process. In this case, the product variants differ in terms of their type and quantity of the components, but not in terms of the manufacturing process sequence. The configuration engineer can store the combination of each individual product variant in a recipe.
Operating recipes 11.2 Structure of a recipe ① File cabinet Recipe collection Recipes for a fruit juice plant ② Drawer Recipe Orange flavored drinks ③ Drawer Recipe Grape flavored drinks ④ Drawer Recipe Apple flavored drinks ⑤ Drawer Recipe Cherry flavored drinks Recipe data records The drawers of the file cabinet are filled with suspension folders. The suspension folders in the drawers represent records required for manufacturing various product variants.
Operating recipes 11.3 Recipes in the project ④ Suspension folder Recipe data record Apple juice Elements In the figure showing the file cabinet, each suspension folder contains the same number of sheets. Each sheet in the suspension folder corresponds to an element of the recipe data record. All the records of a recipe contain the same elements. The records differ, however, in the value of the individual elements. Example: All drinks contain the same components: water, concentrate, sugar and flavoring.
Operating recipes 11.4 Recipe displays Data flow The following figure shows the data flow in a project with recipes. +0, GHYLFH 5HFLSH PHPRU\ 5HFLSH YLHZ 5HFLSH 5HFLSH 5HFLSH 5HFLSH Q 5HFLSH VFUHHQ 5HFLSH WDJ 3/& 0HPRU\ FDUG 11.
Operating recipes 11.4 Recipe displays ● As extended recipe view ● As simple recipe view The configuration engineer also defines which operator controls are displayed in the recipe view. Extended recipe view The following figure shows an example of the extended recipe view.
Operating recipes 11.4 Recipe displays -XLFH %HYHUDJH 1HFWDU ① Number of the recipe data record ② Recipe data records ③ Buttons for changing the displayed list and calling the menu Display of values NOTICE Changing the recipe data record in the background Applies to the processing of a recipe data record: If values of the corresponding recipe data record are changed by a PLC job, the recipe view is not updated automatically.
Operating recipes 11.5 Recipe values in the HMI device and the PLC ① Element name and associated values The element name designates a specific element in the recipe data record ② Buttons for editing a recipe data record ③ Modified recipe view ④ Buttons for transferring recipe data The values displayed or entered in the recipe screen are saved in recipe tags. The recipe values are exchanged with the PLC immediately or later via these tags.
Operating recipes 11.6 Operating the recipe view The values of the recipe view are synchronized with the associated recipe tags. In this case, changes to values in the recipe view have an immediate effect on the values of the associated recipe tags. The values are only synchronized, when an operating element that is outside the recipe view is operated. ● Synchronization by the user: The values of the recipe view and the associated recipe tags are not synchronized automatically.
Operating recipes 11.6 Operating the recipe view ● Save recipe data records or save them under a new name ● Delete recipe data records ● Synchronize values of the recipe view with the associated recipe tags ● Transfer recipe data records from the PLC and to the PLC Operator controls of the recipe view The following table shows the operator controls of the recipe view. Buttons Functions Creates a new recipe data record. If a start value is configured, it is shown in the text box.
Operating recipes 11.6 Operating the recipe view Procedure Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe for which you want to create a new recipe data record. 2. Touch . A new recipe data record with the next available number is created. If you change the new data record number to an existing data record number, the existing data record is overwritten. 3. Enter values for the elements of the data record.
Operating recipes 11.6 Operating the recipe view Procedure Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe which contains the desired recipe data record. 2. Select the recipe data record you want to change. 3. Change the data record as required. 4. Save your changes by means of the button. If you want to save the recipe data record under a different name, touch the key. 5. The recipe data record is saved.
Operating recipes 11.6 Operating the recipe view See also Recipes in the project (Page 279) 11.6.5 Synchronizing tags Introduction The values of the recipe elements can be saved to recipe tags, depending on the configuration. Differences may occur between the display values in the recipe view and the actual values of tags in an ongoing project. Synchronize the tags to equalize such differences. Synchronization always includes all the variables which belong to a recipe data record.
Operating recipes 11.6 Operating the recipe view See also Recipes in the project (Page 279) 11.6.6 Reading a recipe data record from the PLC Introduction In the current project, the values which are also stored in the recipes in the HMI device can be changed directly in the plant. This is the case, for example, if a valve was opened further directly at the plant than is stored in the recipe. The values of the recipe data records saved in the HMI device possibly no longer match the values in the PLC.
Operating recipes 11.7 Operating the simple recipe view 11.6.7 Transferring a recipe data record to the PLC Introduction In order for an edited recipe data record to take effect in the process, you must transfer the values to the PLC. The display values in the recipe view are always transferred to the PLC. Requirements A screen with a recipe view is displayed. Procedure Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe which contains the desired recipe data record.
Operating recipes 11.7 Operating the simple recipe view Operation The simple recipe view can be operated as follows: ● Enter values for the recipe elements ● Create recipe data records ● Save recipe data records or save them under a new name ● Delete recipe data records ● Transfer recipe data records from the PLC and to the PLC Operator controls of the simple recipe view Toggle between the display areas and the context menus to operate the simple recipe views.
Operating recipes 11.7 Operating the simple recipe view ● Element list Menu item Functions Save The selected record is saved. To PLC The displayed values of the selected data record are transferred from the HMI device to the PLC. From PLC The recipe values from the PLC are displayed on the HMI device in the recipe view. Save as The selected data record is saved under a new name. A dialog box opens in which the name is entered. Operating the menu Touch the desired menu command.
Operating recipes 11.7 Operating the simple recipe view The tags of the record can be assigned default values depending on the configuration. 5. Open the menu of the element list and select the command "Save". 6. Enter a name for the new record. 7. Confirm your entries. If you change the new data record number to an existing data record number, the existing data record is overwritten. Result The new recipe data record is saved to the selected recipe. See also Recipes in the project (Page 279) 11.7.
Operating recipes 11.7 Operating the simple recipe view The recipe data record is saved. Result The edited recipe data record has now been saved in the selected recipe. See also Recipes in the project (Page 279) 11.7.4 Deleting a recipe data record Introduction You can delete all the data records which are not required. Requirements A screen with a simple recipe view is displayed. Procedure Proceed as follows: 1.
Operating recipes 11.7 Operating the simple recipe view 11.7.5 Reading a recipe data record from the PLC Introduction The values of recipe elements are exchanged with the PLC via tags. In the current project, the values which are also stored in the recipes in the HMI device can be changed directly in the plant. This is the case, for example, if a valve was opened further directly at the plant than is stored in the recipe.
Operating recipes 11.8 Exporting a recipe data record The display values in the recipe view are always transferred to the PLC. Requirements A screen with a simple recipe view is displayed. Procedure Proceed as follows: 1. If the recipe list contains several recipes: Select the recipe which contains the desired recipe data record. 2. Select the element list of the recipe data record whose values you want to transfer to the PLC. 3. Open the menu. 4. Select the menu item "To PLC".
Operating recipes 11.9 Importing a recipe data record ● The following tags are configured equally in the recipe view and for the "Export record" operating element. – Recipe number – Data record number Procedure Proceed as follows: 1. If the recipe view contains several recipes: Select the recipe which contains the desired recipe data record. 2. Select the recipe data record you want to export. 3. Operate the operator control which was configured for export, for example the "Export data record" button.
Operating recipes 11.10 Examples Result The imported recipe data record is saved on the HMI device.
Operating recipes 11.10 Examples +0, GHYLFH 5HFLSH PHPRU\ 5HFLSH YLHZ 5HFLSH VFUHHQ 5HFLSH 5HFLSH 5HFLSH 5HFLSH Q 5HFLSH WDJ 3/& 11.10.2 ① Display recipe data record ② Save recipe data record ③ Tags are synchronized ④ Display and edit recipe tags in the recipe screen ⑤ Tags are offline Manual production sequence Introduction You request the production data of different workpieces from the PLC and display this data on the screen of the HMI device for inspection.
Operating recipes 11.10 Examples +0, GHYLFH 5HFLSH YLHZ 5HFLSH PHPRU\ 5HFLSH 5HFLSH 5HFLSH 5HFLSH Q 5HFLSH VFUHHQ 5HFLSH WDJ 300 3/& ① The recipe data record is read from the PLC and written to the PLC again following changes ② Display and edit recipe tags in the recipe screen ③ Tags are synchronized ④ Recipe data records are saved in the recipe memory of the HMI device Mobile Panel 277F IWLAN Operating Instructions, 12/2007, A5E01003940-01
Maintenance and care 12.1 12 Maintenance and care Scope of maintenance ● Function tests Carry out the specified tests in the periods of time prescribed for each. Otherwise, the functionality of the HMI device is not guaranteed. To perform the function tests, the HMI device must be switched on but not integrated. – Press the emergency stop button at least once a year. – Press both enabling buttons every time you start a project. ● HMI device The HMI device is designed for maintenance-free operation.
Maintenance and care 12.2 Spare parts and repairs CAUTION Do not clean the HMI device with compressed air or steam jet blowers. Never use aggressive solvents or scouring powder. Use a cleaning cloth dampened with a cleaning agent to clean the equipment. Only use water with a little liquid soap or a screen cleaning foam. Procedure Proceed as follows: 1. Switch off the HMI device. 2. Spray the cleaning solution onto a cleaning cloth. Do not spray directly onto the HMI device. 3. Clean the HMI device.
Maintenance and care 12.2 Spare parts and repairs – Lock – Key set for lock – Counterpart for power supply connector The service pack can be ordered from your Siemens representative. Replacement key set You can order a replacement key set for the HMI device from your Siemens sales office. Replacement batteries Main batteries and bridge batteries can be ordered from your Siemens sales office.
13 Technical specifications 13.1 Dimension drawings 13.1.
Technical specifications 13.
Technical specifications 13.1 Dimension drawings Charging station 13.1.
Technical specifications 13.2 Specifications Transponder 13.1.3 $OO GLPHQVLRQV LQ PP 13.2 Specifications 13.2.1 Mobile Panel 277F IWLAN HMI device Weight with battery and without packaging Max. 2.2 kg Display Type Display area, active Resolution 308 Color TFT LC display 151.66 mm x 113.74 mm (7.
Technical specifications 13.
Technical specifications 13.2 Specifications Additional specifications Drop height with main battery Max. 1.2 m Buffer time of internal clock with bridging battery inserted Approx. 4 days Radio link to transponder • Frequency band • Transmission angle • • 2400 - 2483 MHz Approx. 83 ° Fail-safe mode WARNING The safety characteristics in the specifications apply for a proof-test interval of 10 years and a mean repair time of 8 hours.
Technical specifications 13.2 Specifications Quantity structure for the effective range concept F-FBs required in safety program F_FB_MP 1x per Mobile Panel 277F IWLAN, maximum 126 F_FB_RNG_4 1x per effective range, for which up to 4 HMI devices have logging on authorization F_FB_RNG_16 1x per effective range, for which up to 16 HMI devices have logging on authorization DB_STATES 1 Configuring 13.2.
Technical specifications 13.2 Specifications 13.2.3 Charging station Weight Weight without packing Approx. 1.1 kg Nominal voltage +24 VDC Range, permissible 19.2 V to 28.8 V (–20%, +20%) Transients, maximum permissible 35 V (500 ms) Time between two transients, minimum 50 sec Current consumption with Mobile Panel • Typical • Constant current, maximum • Power on current surge I2t • • • Approx. 1.5 A Approx. 1.8 A Approx. 1.
Technical specifications 13.2 Specifications 13.2.5 Description of interfaces on the HMI device USB The figure below shows the pin assignment of the USB interface. Pin Assignment 1 +5 VDC, out (max. 100 mA) 2 USB-DN 3 USB-DP 4 GND RJ45 The figure below shows the pin assignment of the RJ45 interface. Pin Assignment 1 TD+ 2 TD– 3 RD+ 4 n. c. 5 n. c. 6 RD– 7 ICD+ 8 ICD– WLAN WLAN in accordance with IEEE 802.
Technical specifications 13.3 Radiation characteristic 13.3 Radiation characteristic 13.3.1 Radiation characteristic of the transponder Antenna type Dual port patch antenna Polarization Vertical and horizontal Frequency band 2400 - 2483 MHz Antenna gain Max. in main count direction • Port 1: 2,6 dBic • Port 2: 2.7 dBic Impedance 50 Ω Full widths at half maximum, horizontal at 2.45 GHz 93° Full widths at half maximum, vertical at 2.
Technical specifications 13.
Technical specifications 13.3 Radiation characteristic x -15° -30° 15° 30° 8m 7m 45° -45° 6m 5m 60° -60° 4m 3m -75° 75° 2m 1m z -90° -105° 105° -120° 120° 135° -135° 150° -150° -165° 165° 180° 13.3.
Technical specifications 13.3 Radiation characteristic Antenna gain Max. in main count direction • Port 1: 2,6 dBic • Port 2: 2.7 dBic Impedance 50 Ω Full widths at half maximum, horizontal at 2.45 GHz 83° Full widths at half maximum, vertical at 2.45 GHz 80° Ranges depending on angular displacement to main count direction The figure below shows the coordinate system applied to the HMI device. ] ] [ \ The figure below shows the HMI device range depending on the angular displacement to the main co
Technical specifications 13.
Technical specifications 13.
B Appendix B.1 ESD guideline Definition of ESD All electronic modules are equipped with large-scale integrated ICs or components. Due to their design, these electronic elements are highly sensitive to overvoltage, and thus to any electrostatic discharge. These electronic components are therefore specially identified as ESDs.
Appendix B.1 ESD guideline Electrostatic charging CAUTION Electrostatic charging ESDs may be destroyed by voltages far below the level perceived by human beings. Voltages of this kind develop when a component or an assembly is touched by a person who is not grounded against static electricity. Usually, it is unlikely that damage to an ESD as a result of overvoltage is detected immediately but may become apparent only after a longer period of operation.
Appendix B.2 System alarms As a rule, only touch the ESD if this is unavoidable, for example for maintenance. When you touch modules, make sure that you do not touch the pins on the modules or the PCB tracks. In this way, the discharged energy cannot reach and damage the sensitive devices. Discharge electrostatic electricity from your body if you are performing measurements on an ESD. Do so by touching grounded metallic parts. Always use grounded measuring instruments. B.
C Abbreviations C.
Abbreviations C.1 Abbreviations 326 MPI Multipoint Interface (SIMATIC S7) MS Microsoft MTBF Mean Time Between Failures n. c.
Glossary "Transfer" mode An operating mode of the HMI device in which an executable project is transferred from the configuring PC to an HMI device. Access point The access point is a WLAN participant that also performs administrative functions on the network. Acknowledge Acknowledgment of an alarm confirms that it has been noted. Ad hoc mode WLAN network without access point Alarm logging Output of user-specific alarms to a printer, in parallel to their output to the HMI device screen.
Glossary Automation system Controller of the SIMATIC S7 series such as a SIMATIC S7-300 Bootloader Used to start the operating system. Automatically started when the HMI device is switched on. After the operating system has been loaded, the Loader opens. Configuration software Software used to generate projects used for the purpose of process visualization. An example of configuring software is WinCC flexible.
Glossary Fail-safe Ability of a technical system to remain in a safe state or switch to another safe state immediately after certain failures occur. Fail-safe mode See Safety mode. Fail-safe system, F system Fail-safe systems are used to control processes in which immediate shutdown results in a safe system state. This means that an immediate shutdown does not result in danger to people or the environment. F systems are used in systems requiring higher levels of safety.
Glossary HMI device image A file that can be transferred from the configuring PC to the HMI device. The HMI device image contains the operating system and elements of the runtime software required to run a project. I/O field An I/O field enables the input or output of values on the HMI device which are transferred to the PLC. Infotext An infotext is a configured information on objects within a project.
Glossary PROFINET Within the framework of Totally Integrated Automation (TIA), PROFINET represents an enhancement of the following bus systems: ● PROFIBUS DP as well-established fieldbus ● Industrial Ethernet as the communications bus for the cell level The experience gained from both systems has been and continues to be integrated in PROFINET. PROFINET as an Ethernet-based automation standard from PROFIBUS International (PROFIBUS Nutzerorganisation e.V.
Glossary Project Result of a configuration using a configuration software. The project normally contains several screens with embedded system-specific objects, basic settings and alarms. The project file of a project configured in WinCC flexible is saved under the file name extension *.hmi. You need to distinguish between a project on the configuring PC and that on an HMI device. A project may be available in more languages on the configuring PC than can be managed on the HMI device.
Glossary Safe state State of a unit in which safety is assured. In other words, the risk is acceptably low because it has been established that safety-related malfunctions do not occur or because of the safety measures taken to prevent possible safety-related malfunctions. The basic principle of the safety concept in a fail-safe system is the existence of a safe state for all process variables.
Glossary System alarm A system alarm is assigned to the "System" alarm class. A system alarm refers to internal states on the HMI device and the PLC. Tab sequence During configuration, this defines the sequence in which objects are activated on pressing the key. Tag Defined memory location to which values can be written to and read from. This can be done from the PLC or the HMI device.
Index " "Override" mode, 226 / /Audit, 32 A Acceptance, 196 Effective ranges and transponders, 196 Plant, 196 Accessories Accessory kit, 20, 23, 26 Accessory kit, 20 Charging station, 23 Transponder, 26 Acknowledge Alarm, 276 Error alarm, 276 Activate Password protection, 146 Ad hoc mode, 58 Address assignment TCP/IP network, 169 Addressing, 167 Admin, 268, 269 Agency, 7 Alarm, 271 Acknowledge, 276 Alarm indicator, 272 Display, 273 Editing, 276 Functional scope, 29 Alarm buffer, 272 Functional scope, 29 A
Index Required, 4 BAT LED, 98 BAT 1 LED, 122 BAT 2 LED, 122 Batteries Charging in the charging compartment, 120 Battery, 246 Application, 246 Charging options, 22 Layout, 246 LED display, 87 Maintenance cycle, 301 Operation, 246 Purpose, 22 State, 181 Battery charging status Vibration alarm, 159 Battery status Display, 87, 136 BGIA approval, 38 Booting, 156 Bridging battery, 21, 22 Changing, 89 Insert, 85 Safety instruction, 88, 90 Brightness Changing, 152 Browser Homepage, 136 Setting, 136 Byte assignment
Index Open, 135 Operating, 137 Password protection, 127 Screen keyboard, 138 Cookies, 136, 175 Country code, 129 CRC checksum Determining, 197 Creating Recipe data record, 285, 292 Users, 266 Currency, 137 D Data channel Enabling, 160 Locking, 160 Parameter assignment, 137, 160 Data flow, 280 Data record list, 281, 291 Data transfer rate to Access Point, 130 Date, 136 Entering, 243 Setting, 147 Synchronizing, 148 Date format, 137, 149 Date/time properties, 136, 147 Deactivating Password protection, 147 De
Index EMC, 46 Guideline, 37 Emergency stop, 220 Emergency stop button Effectiveness, 40, 44 Operating, 43, 101 Release, 101 Safety instruction, 43 Emission, 42, 47 Enabling button, 44, 102 Operating, 103 Panic activation, 104 Risk from improper use, 46 Safety instruction, 46 Switch settings, 103 Enabling device, 44 Encryption, 175 Entering Alphanumerical value, 242 By means of function key, 237 Date, 243 Numerical value, 241 Recipe data record, 298 Symbolic value, 244 Text box, 239 Time, 243 Error alarm Ac
Index Ports, 76, 309 Restart, 156 Restarting, 136 Specifications, 308 Storing, 219 Switch off, 93 HMI Input Panel Options, 140 Homepage Internet, 174 Host cable Safety instruction, 78 I Identification, 171 Illuminated pushbutton Application, 112 Bit assignment, 112 Operating, 106 Importing Certificate, 176 Recipe data record, 297 Infotext Display, 244, 275 Functional scope, 31 Initial startup, 189 Input Panel, 136 Input unit, 96 Specifications, 309 Installation Electrical, 69 EMC-compliant, 46 Installing
Index License key, 215 Transferring, 189, 216 Transferring back, 189, 217 Limit value For password, 263 For user, 263 For user view, 263 Limit value monitoring Functional scope, 29 Limit value test, 241 Loader Buttons, 125 Open, 126 Local rampdown, 221 Log Functional scope, 30 Logbook WLAN connection, 134 Logoff Effective range, 226 Users, 266 Logoff time, 262 Logon Effective range, 224 Users, 264 Logon data, 171 M Main battery, 21, 22 Changing in good time, 88 Insert, 86 Main battery change Block of USB
Index Decimal places, 241 Display format, 240 Entering, 241 Limit value test, 241 O Offices, 7 Offline Operating mode, 186 Recipe tag, 284 Test, 195 Online Operating mode, 187 Recipe tag, 284 Test, 195 OP properties, 136 Device, 157 Memory monitoring, 182 Persistent storage, 150 Touch, 144 Open Loader, 126 Operating Control Panel, 137 Emergency stop button, 43, 101 Enabling button, 103 Feedback, 236 Handwheel, 104 Illuminated pushbutton, 106 Key-operated switch, 105 Recipe menu, 292 Recipe screen, 285, 29
Index Transferring recipe data record, 290, 295 PLC, 32 PLC_User, 268, 269 Ports, 76 HMI device, 309 POWER LED, 122 Power failure, 201, 205 Power Save 1, 98, 152 Power Save 2, 98, 152 Power supply, 41 Charging station, 41 Tabletop power supply unit, 41 Precautions Electrostatic discharge, 322 Printer Connecting, 80 Connection graphic, 80 Setting, 137 Printer connection Setting, 154 Printer properties, 137, 154 Printing Labeling strips, 117 Via network printer, 168 Production sequence Manual, 299 PROFINET,
Index Menu items, 291 Operator control, 285, 291 Simple, 281 Recommissioning, 189 Recycling, 7 Red error display, 233 Regional and language settings, 137, 149 Regional settings, 149 Registered trademarks, 6 Registry information Backup, 136, 150 Regulations for the prevention of accidents, 35 Remote control Forcing permission, 260 Start, 260 Removing, 223 Option, 188, 212, 213, 215 Repairs, 302 Replacement key set, 303 Reset button, 77 Resetting to factory settings with ProSave, 210 Resetting to factory set
Index USB connection sequence, 78 USB Host-to-Host cable, 78 USB interface, 82 SAR, 47 Scaling Functional scope, 29 Scope of delivery, 65 Screen Functional scope, 30 Screen keyboard, 136, 239 Adjust size, 139 Alphanumerical, 242 Change layout, 139 Character repeat, 141 Configure, 140 For Control Panel, 138 Keyboard level, 242 Language change, 242 Move, 139 Numerical, 240 Representation types, 138 Screen saver, 137, 153 Setting, 152 Screen setting Changing, 152 Search engine Internet, 174 Security settings,
Index Touch operation, 258 Stop Safety instruction, 44 Subnet Mask, 170 Supply voltage, 312 Specifications, 309 Support On the Internet, 7, 303 Switch off HMI device, 93 Switch setting Enabling button, 103 Switches, 253 Switching on Mobile Panel, 91 Switch-off behavior Emergency stop, 220 Global rampdown, 221 In the plant, 220 Local rampdown, 221 Shutdown, 221 Trigger, 221 Symbolic value Changing, 244 Entering, 244 Synchronizing Date and time, 148 Recipe tag, 283, 288 System, 158 Acceptance, 196 System fun
Index Limit violation, 255 TÜV, 38 U UL approval, 37 Unattended in effective range Application case, 220, 225, 233 Unintentional action, 236, 238 Updating About ProSave, 207 Operating system, 204 Using WinCC flexible, 206 Updating the operating system, 188 Usage Conditions, 51 Geographical, 42 In industry, 42 In residential areas, 42 With additional measures, 51 USB Connection sequence, 78 USB connection sequence Safety instruction, 78 USB device Connecting, 81 USB FlashDrive, 21 USB interface Block durin
Index Rules, 59 Testing, 200 Mobile Panel 277F IWLAN Operating Instructions, 12/2007, A5E01003940-01 347
