User's Manual

ManualsBrandsSiemens Medical Solutions, Department MED EH&S ManualsElectronicsHand RC for medical x-ray-systems

Table Of Contents

AXIOM Aristos FX AXB4-310.621.01.01.02 - Draft - 1 / 8

Addendum

AXIOM Aristos FX

Wireless Remote Control - Draft -

Important information

The functions of the Wireless Remote Control are activated via an RF transmitter.

The Wireless Remote Control shall be operated in close vicinity to the patient

table only and with full visibility to the patient on the table.

The batteries shall always be sufficiently charged.

The Wireless Remote Control can interfere with life supporting devices.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user´s authority to operate the equipment.

The Wireless Remote Control may be interfered with by other equipment, includ-

ing portable and mobile RF communication equipment, even if such equipment

meets the applicable emissions requirements.

The Wireless Remote Control must emit electromagnetic energy in order to per-

form its intended function. Nearby electronic equipment may be affected.

hm_fdrad_sysmark_MovementInte

rruptbyStop_u06

Caution

Mechanical or personal damage

Emergency stop interrupts movements immediately

◆ Use remote control only when there is visual and accoustic contact with

patient.

◆ In case of unintended movement press next emergency STOP button.

Summary of content (8 pages)

PAGE 1
Addendum AXIOM Aristos FX Wireless Remote Control - Draft Important information The functions of the Wireless Remote Control are activated via an RF transmitter. The Wireless Remote Control shall be operated in close vicinity to the patient table only and with full visibility to the patient on the table. The batteries shall always be sufficiently charged. The Wireless Remote Control can interfere with life supporting devices.
PAGE 2
Wireless Remote Control - Draft - Operation Display area Operation area Selection area Wireless Remote Control (example) The remote control is active in a range of appr. 5 m around the table/stand, where the receiver is mounted. If the remote control is in a wider range of the table, it may lose contact with the receiver and will then turn into an inactive mode. 2 /8 AXB4-310.621.01.01.
PAGE 3
Wireless Remote Control - Draft Display area There are 3 LEDs showing the status of the remote control. Green LED on: Remote control is on and is in active mode. Green LED off: Remote control is inactive. – It is too far away from the table – The Aristos FX is switched off – The batteries are completely discharged – The remote control is in “sleep mode”. Press a button swiftly to activate it again. Orange LED on: An operation button is being pressed.
PAGE 4
Wireless Remote Control - Draft Operation area Dead-man switch On the backside of the remote control there is a dead-man switch. To execute an operation with a button of the operation area you have to press the dead-man switch simultaneously. As soon as you release the dead-man switch, the current operation is stopped.
PAGE 5
Wireless Remote Control - Draft Opening/closing the collimator; moving tube unit and detector in x and y direction (orange and green) Closing the collimator in transverse direction Moving tube unit and detector in x direction (orange) Opening the collimator in transverse direction Moving tube unit and detector in x direction (orange) Closing the collimator in longitudinal direction Moving tube unit and detector in y direction (green) Opening the collimator in longitudinal direction Moving tube unit and d
PAGE 6
Wireless Remote Control - Draft ’Center lock’ tracking Disable/enable ’center lock’ tracking – Press the ’center lock’ tracking button just for a short time (< 3 s) to activate or deactivate center-lock tracking at the current position. When an OGP with centered tracking is selected press the tracking button longer than 3 s and keep it pressed (dead man switch). Detector and tube unit are then centered as programmed.
PAGE 7
Wireless Remote Control - Draft Charging Station The Wireless Remote Control is plugged in the Charging Station for charging the batteries. It is recommended to charge the batteries every day after deployment. Charging Station If the Wireless Remote Control needs charging during a patient procedure, simply plug it in the Charging Station. Never use another charging device than the Charging Station delivered with the Wireless Remote Control.
PAGE 8
Wireless Remote Control - Draft Technical Data Active range Approximately 5 m around the receiver mounted to the stand. Charging time Approx. 2 h Operating time with full batteries Approx. 12 h Frequency range 2402 MHz - 2480 MHz Modulation GFSK RF Power 0 dBm RF emissions CISPR 11 Compliance: Group 2 The deployment of Wireless Remote Control in combination with Aristos FX changes the classification of Artis from compliance group 1 to compliance group 2. 8 /8 AXB4-310.621.01.01.