® SIDEPOWER Radio link 8970/ 8975 m GB Installation and user’s manual Installations und Bedienungsanleitung © Sleipner Motor AS 2004 SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 www.side-power.com sidepower@sleipner.
GB Contents Inhalt D Model range ....................................................... 2 Modellübersicht .................................................. 2 Technical specifications ...................................... 3 Technische Daten ............................................... 3 Important precautions ......................................... 3 Vorsichtshinweise ............................................... 3 Receiver and transmitter installation ..................
GB Technical specifications and important precautions Model Power feed Frequency (MHz) Adress range Operation temp. Technology HxWxD (mm) Weight (g) Radio link transmitter 8975 From 12/24 V power system 433,92 65.000 -150C / +550C S.M.T. ----- Receiver 8918 From thruster 433,92 65.000 -150C / +550C S.M.T. 145x60x35 180 You must always install at least one original Sidepower panel to operate the system.
Receiver and transmitter installation GB Prior to installation, it is important that the installer reads this guide to ensure necessary acquaintance with this product. Attention ! Install the receiver with at least 1 m distance from high power cables and NMEA cables or other sources of electrical interference. Install the receiver with at least 1 m distance from electro motors and generators. Install the receiver on the bridge area, not in the hull.
GB «Visual» wiring diagram D Schaltplan - Übersicht Transmitter unit / Sendereinheit Receiver / Empfänger Sidepower radio remote control V1.
GB Programming the system when using additional radio link transmitters or remote control transmitters The original radio link transmitter and receiver have the same factory preset code. When additional radio link transmitters or remote control transmitters are to be used, the whole system (incl. all transmitters) must be programmed again. 1. Deactivate all transmitters and the receiver (press “OFF” on the control panels(s) / transmitter(s) and turn off the main power switch for the thruster system. 2.
GB Important user precautions Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources (batteries) so that the thruster can be turned off in case of a malfunction. If a Sidepower automatic main switch is fitted, the “OFF” button will shut off the main switch providing no other control panels are “ON”. The thruster system is activated by pushing the two “ON” buttons if the main power source for the thruster system is turned on.
Radio link / control panel unit ‘ON’ Turn boat to port Radio link / control panel unit ‘OFF’ Turn boat to starboard Bow+Stern Thruster AUTO-OFF appr. 4 minutes GB How to use Sidepower How to use a bowthruster 1. Turn the main power switch for the bow thruster on. 2. Turn on the radio link transmitter / control panel unit by pushing the two “ON” buttons. The system is now activated for appr. 4 min. and then turns off automatically. 3.
Argentina Trimer SA Buenos Aires Tel: +54 11 4580 0444 Fax: +54 11 4580 0440 www.trimer.com.ar trimer@trimer.com.ar Australia AMI Sales Freemantle, WA Tel: +61 89 337 3266 Fax: +61 89 314 2929 ami@amisales.com.au Austria G. Ascherl GmbH Hard, Bregenz Tel: +43 5574 899000 Fax: +43 5574 89900-10 www.ascherl.at office@ascherl.at Benelux ASA Boot Electro Watergang Tel: +31 20 436 9100 Fax: +31 20 436 9109 asaboot@worldonline.nl info@asabootelectro.
