SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 w w w. s i d e - p o w e r. c o m s i d e p o w e r @ s l e i p n e r. n o Made in Norway Installation & User Manual Radio Remote RC-10E © Sleipner Motor AS version 1.
Contents Model range................................................................................................................................ 2 Technical specifications............................................................................................................... 3 Important precautions.................................................................................................................. 4 Receiver installation................................................................
Technical specifications Model Power feed Frequency (MHz) Operation temp. HxWxD (mm) Weight (g) Transmitter RCT-10E 1 x 3V battery (type: CR2032) 433,2 -10°C / +55°C 95x48x25 60 Voltage: Load, max Receiver RCR-1E From thruster 433,2 -15°C / +55°C 89x68x33 135 8-30V 4A Operating range: 15m under normal operating conditions Important precautions • You must always install at least one original Side-Power panel.
Receiver installation Prior to installation, it is important that the responsible installer reads this guide to ensure necessary acquaintance with this product. Warning! • Remote receiver power supply negative lead must be connected to the thrusters`s negative lead. Caution! • Install the receiver minimum 1 meter (3ft) from high power cables and NMEA cables or other sources of electrical interference, i.e. navigation instruments, radio communication devices, electro motors and generators.
Installation & User Manual, Radio Remote RC10E Page 5
Receiver installation If the receiver is mounted against a wall, us spacers between the receiver and the wall to avoid moisture in the receiver. Mount the receiver by using the 2 screwholes. To bow thruster To bow thruster control panel Yellow: Automatic main switch (optional) Black: 12/24V Batt. Red: 12/24V Batt.
Programming additional receivers Push the Pair Button with a plastic stick The original transmitter and receiver have the same factory preset code so that no programming is necessary. When additional transmitters are to be used, the receiver must be programmed again for all transmitters. 1. Deactivate the receiver and all transmitters (press “OFF” on all transmitters). Turn off the main power switch for the thruster(s). 2. Turn on the power to the receiver. 3.
Replacing the battery Battery B A A B WARNING: Before working on the transmitter, deactivate the transmitter and the receiver (push “OFF” on the transmitter(s)) and turn off the power to the receiver as well as the thruster mainswitch. 1. Open the transmitter. 2. Take out the battery by inserting a screwdriver or similar between battery and holder at point A, and gently flip the battery out, taking care not damaging the battery grips at point B 3.
Important user precautions • Ensure that you know the location of the main battery switch that disonnects the thruster from all power sources (batteries) so that the thruster can be turned off in case of a malfunction. • If a Side-Power automatic main switch is fitted, the “OFF” button on your transmitter will shut off the main switch providing no other control panels are “ON”. • How to activate the system: Turn on the main power source for the thruster system. Turn on the power to the receiver.
Remote control “ON” Remote control “OFF” Turn boat to Port Bow + Stern thruster Turn boat to Starboard Auto-OFF appr. 4 min. Hold for 2 seconds How to use a bow thruster 1. Turn the main power switch for the bow thruster on. Turn on the power to the receiver. 2. Turn on the transmitter by pushing the transmitter’s two “ON” buttons. The remote system is now activated and then turns off automatically appr. 4 min. after the last usage (see page 9). 3.
Electric schematics Receiver Insulation Optional Auto main switch +12/24V supply Optional Auto main switch +12/24V supply Page 11 Installation & User Manual, Radio Remote RC10E Active antenna (Yellow) Red
SIDE-POWER SERVICE CENTRES Argentina Trimer SA Buenos Aires Tel:+54 11 4580 0444 Fax:+54 11 4580 0440 www.trimer.com.ar trimer@trimer.com.ar Estonia/Latvia/Lithuania Miltec Systems OÜ Tallin Tel: +372 5013997 Fax: +372 6442211 www.miltec.ee tony@miltec.ee Japan Turtle Marine Inc. Nagasaki Tel:+81 95 840 7977 Fax:+81 95 840 7978 www.turtle-marine.com info@turtle-marine.com Spain Imnasa Marine Products Girona Tel:+34 902 300 214 Fax:+34 902 300 215 www.imnasa.com imnasa@imnasa.