WF-R710-RTG1 IEEE 802.11b/g/n 1T1R UART SoC Module Features： ➢ Reserving System IEEE Std. 802.11b/g/n Wi-Fi 1T1R System-on-Chip UART module ➢ Chip Solution RTL8710B ➢ I/O Interface & Size Standard two UART/GPIO I/O Interface Support RF Testing and OTP/Flash Programming 17.7mm x30.0mm x2.9mm Model Overview： Model Interface RF Standard Data rate Freqency I/O Voltage Input WF-R710-RTG1 UART IEEE 802.11b/g/n 150 Mbps 2.4G GPIO 3.3V 1.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module WF-R710-RTG1 SoC module designed base on RTL8710BN chip solution, The SOC module is a highly intelligent platform for the Internet of Everything that contains a low-power Wi-Fi connectivity solution on one package. It includes a number of TCP/IP based connectivity protocols along with SSL, enabling a low-cost, low-complexity system to obtain full-featured internet connectivity and reliable information exchange.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module SoC RF specification refer to below list. Main Chipset SoC RF standard Operating Frequency UART Interface Antenna Design Options RF Modulation Data rates Operation Voltage RTL8710BN-A0 IEEE 802.11 b/g/n 2.412~2.462 GHz For testing and OTP programming (Calibration data) PCB printed WIFI: 11b: DBPSK, DQPSK and CCK and DSSS 11a/g: BPSK, QPSK, 16QAM, 64QAM and OFDM 11n: BPSK, QPSK, 16QAM, 64QAM and OFDM 11b: 1, 2, 5.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module 2.1 PCBA Mechanical Outline Drawing Typical Dimension (W x L x T): 17.7mm x30.0mm x2.9mm (+/-0.2 mm) PCB Thickness: 1mm (+/-0.2mm) 2.2 Pin Distribution Definition Pins sequence and distribution list as follows Pin Define 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SWD_CLK SWD_DATA GND 3.3V IO0 TXD RXD IO12 IO5 TX RX I2C_SDA I2C_SCL NC 3.3V GND NC NC 3. Electrical Specification Sichuan AI-Link Technology Co.,Ltd.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module This Specification is based-on conductive DVT testing result. The extreme condition include overall temperature +25℃ and overall voltage 3.3V. 3. 1 IEEE 802.11b Section: Items Contents Specification Mode Channel Data rate TX Characteristics 1. Power Levels(Calibrated) 1) 17dBm Target (For Each antenna port) 2. Spectrum Mask @ Target Power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3. Constellation Error(EVM) @ Target Power 1) 1Mbps 2) 2Mbps 3) 5.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module Items Contents Specification IEEE802.11g Mode BPSK, QPSK, 16QAM, 64QAM and OFDM Channel CH1 to CH13 @ 11g Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics 1. Power Levels 1) 15dBm Target (For Each antenna port) @ 11g 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 4.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module Items Contents Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 14dBm Target (For Each antenna port) @ 2.4G 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT20 @ 2.4G RX Characteristics 5.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module Items Contents Specification Mode Channel Data rate (MCS index) TX Characteristics 1. Power Levels 1) 14dBm Target (For Each antenna port) @ 2.4G 2. Spectrum Mask @ Target Power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 3. Constellation Error(EVM) @ Target Power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 4. Frequency Error 1) IEEE802.11n HT40 @ 2.4G RX Characteristics 5.
WF-R710-RTG1 IEEE 802.11 b/g/n 1T1R UART SoC Module This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
