ADX1M Bodypack Transmitter ADX1M Micro Bodypack Transmitter User Guide Version: 10 (2020-A)
Shure Incorporated Table of Contents Audio Menu 10 Utilities Menu 10 ADX1MBodypack Transmitter 3 WARNING 3 IR Sync 11 ADX1M Axient Digital Micro Bodypack Transmitter 3 Setting the Frequency Manually 12 RF Mute 12 Safe Start 13 Wearing the Bodypack Transmitter 13 Input Overload 14 Matching Audio Levels with Mic Offset 14 Tone Generator 14 ShowLink Test 15 Updating Firmware 15 Features 3 Included Components 4 Optional Accessories 4 ADX1M Transmitter Overview Home Screen Di
Shure Incorporated ADX1M Bodypack Transmitter WARNING • Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate. • Follow instructions from manufacturer • Only use Shure charger to recharge Shure rechargeable batteries • WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type. • Never put batteries in mouth.
Shure Incorporated • Frequency Diversity selection using two bodypacks • Shure SB910M rechargeable batteries for up to 7 hours of runtime, precision metering, and zero memory effect Design • • • • • • Small and streamlined design for better concealment and wear ® Ultem PEI plastic construction for heat resistance and durability Sealed buttons and LEMO connection for protection against sweat, spray, and moisture ingress Recessed LEMO connector High-contrast OLED display Detachable belt clip Included Comp
Shure Incorporated ⑥ Enter Button Selects menu screens for editing and confirms parameter changes. ⑦ Display View menu screens and settings. Press any button to activate the backlight. ⑧ Power LED ◦ Green = unit is powered on ◦ Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting) ⑨ Battery Latch Latch to secure the battery. ⑩ Battery Shure rechargeable battery. Home Screen Display The home screen shows transmitter information and status.
Shure Incorporated The following icons indicate transmitter settings: Battery runtime in hours and minutes or bar display Key: Displayed when encryption is enabled Lock: Displayed when controls are locked. Icon will flash if access is attempted to a locked control (power or menu).
Shure Incorporated ◦ Power: The power switch is locked ◦ Menu: The menu parameters are locked ◦ All: The power switch and menu parameters are locked 2. Press O to save. Tip: To quickly unlock a transmitter: Press O twice, select None, and press O. Shure Rechargeable Batteries Shure lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50% capacity in one hour and reach full charge within three hours.
Shure Incorporated Battery Installation Removing the Battery ① Pull back to disengage the battery latch. ② Slide the battery out of the transmitter. Installing the Battery ① Slide the battery into the transmitter. ② Fully engage the latch to secure the battery ADX1M SB910M Battery Runtime Note: Higher RF power levels decrease battery runtime. Battery runtime varies with battery age and environmental conditions. 2 mW 10 mW 20 mW 6.5 to 8.5 hours 6.0 to 8.0 hours 5.0 to 6.
Shure Incorporated Tips for Editing Menu Parameters • To access the menu options from the home screen, press O . Use the arrow buttons to access additional menus and para meters.
Shure Incorporated ◦ Mute: RF signal is inactive Audio Menu Offset Adjust Offset level to balance mic levels when using two transmitters or when assigning multiple transmitters to receiver slots. Adjustment range: -12 dB to +21 dB. Polarity Selectable polarity assignment for audio input connector: ◦ Pos: Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output) and the tip of the TRS output.
Shure Incorporated When enabled, press the enter button to drop a marker in Wireless Workbench. Battery Displays battery information: ◦ ◦ ◦ ◦ ◦ Battery Life: Runtime reported in bar display and time (hours:minutes) Charge: Percentage of charge capacity Health: Percentage of current battery health Cycle Count: Total of the number of charging cycles for the installed battery Temperature: Battery temperature reported in Celsius and Fahrenheit Talk Sw Press ENTER to add control from a talk switch.
Shure Incorporated Note: Any change to the encryption status on the receiver (enabling/disabling encryption) requires a sync to send the settings to the transmitter. New encryption keys for the transmitter and receiver channel are generated on every IR sync, so to request a new key for a transmitter, perform an IR sync with the desired receiver channel. Setting the Frequency Manually The transmitter can be manually tuned to a specific group, channel, or frequency. 1.
Shure Incorporated 1. From the Radio menu, navigate to Output. 2. Choose one of the following options: ◦ On: RF signal is active ◦ Mute: RF signal is disabled 3. Press O to save. Turning the transmitter off and on, or replacing the battery will restore Output to On. Safe Start Power on in Safe Start mode to prevent interference with other devices. Hold the ^ button while powering on your device until the Safe Start menu appears.
Shure Incorporated Input Overload The OVERLOAD message is displayed when the audio input experiences a high-level input signal. Reduce the input signal or move mic away from the source to remove the overload. Matching Audio Levels with Mic Offset When linking two or more transmitters to a receiver, there may be a difference in volume levels between microphones or instru ments.
Shure Incorporated Tone Generator The transmitter contains an internal tone generator that produces a continuous audio signal. The tone is helpful when conduct ing a sound check or for troubleshooting the audio signal chain. The level of the tone is adjustable from -60 dB to 0 dB and the frequency can be set to 400 Hz or 1000 Hz. Tip: Always start with the level set to -60 dB to avoid overloading speakers or headphones. 1. From the Audio menu select Tone Gen. 2. Set the frequency to 400 Hz or 1000 Hz. 3.
Shure Incorporated Firmware Versioning When performing an update, first download firmware to the receiver, and then update transmitters to the same firmware version to ensure consistent operation. The firmware numbering for Shure devices uses the following format: MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all devices on the network (including transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g., 1.2.x). Updating the Transmitter 1. Download the firmware to the receiver. 2.
Shure Incorporated Storage Temperature Range -29°C (-20°F) to 74°C (165°F) Note: Battery characteristics may limit this range. Audio Input Connector Lemo Connector Configuration Unbalanced Impedance 8.2 kΩ Maximum Input Level 1 kHz at 1% THD 8.5 dBV (7.
Shure Incorporated ShowLink Network Type IEEE 802.15.4 Antenna Type Zigbee Dual Conformal Frequency Range 2.40 to 2.
Shure Incorporated Band Frequency Range (MHz) RF Power (mW)*** K56 606 to 714 2/10/20 K57 606 to 790 2/10/20 K58 622 to 698 2/10/20 L54 630 to 787 2/10/20 R52 794 to 806 10 JB 806 to 810 2/10 X55 941 to 960 2/10/20 *with a gap between 608 to 614 MHz. **with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz. ***power delivered to the antenna port. †operation mode varies according to region. In Brazil, High Density mode is used.
Shure Incorporated G56 470-636 MHz Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich A, B, BG, CH, CY, CZ, D, DK, EST, F * FIN, GB, GR, H, HR, I, IRL, IS, L, LT * M, N, NL, P, PL, RO, S, SK, SLO, TR * all other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated LICENSING INFORMATION Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability de pends on the user’s classification and application, and on the selected frequency.
Shure Incorporated Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
