ADX1 Bodypack Transmitter User guide for the Shure ADX1 digital wireless bodypack transmitter.
Shure Incorporated Table of Contents Audio Menu 11 Utilities Menu 11 ADX1Bodypack Transmitter 3 WARNING 3 IR Sync 12 ADX1 Axient Digital Bodypack Transmitter 3 Setting the Frequency Manually 13 Wearing the Bodypack Transmitter 13 RF Mute 14 Safe Start 14 Input Overload 15 Matching Audio Levels with Mic Offset 15 Tone Generator 16 ShowLink Test 16 Updating Firmware 16 Features 3 Included Components 4 Optional Accessories 4 ADX1 Transmitter Overview Transmitter Controls Lo
Shure Incorporated ADX1 Bodypack Transmitter WARNING • Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate. • Follow instructions from manufacturer • Only use Shure charger to recharge Shure rechargeable batteries • WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type. • Never put batteries in mouth.
Shure Incorporated Design • • • • • TA4 or LEMO3 audio connector option Backlit LCD with easy to navigate menu and controls Durable, moisture-resistant, lightweight metal case Flexible ¼ wave antenna Menu and power lockout Power • Shure SB910 rechargeable batteries for up to 10 hours of runtime, precision metering, and zero memory effect • AAA-compatible battery sled available • External charging contacts for docked charging Included Components SB910 Shure Rechargeable Battery (2) 95A24832 ¼ wave ante
Shure Incorporated ③ Control Buttons Use to navigate through parameter menus and to change settings. ④ Battery Compartment Requires Shure SB910 rechargeable battery. ⑤ Battery Door Latching door to secure battery. ⑥ SMA Connector Connection point for RF antenna. ⑦ Infrared (IR) Port Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup. ⑧ Power Switch Powers the unit on or off.
Shure Incorporated Transmitter Controls Use the controls to navigate through parameter menus and change values. X Acts as a 'back' button to return to previous menus or parameters without confirming a value change O Enters menu screens and confirms parameter changes ∨∧ Use to scroll through menu screens and to change parameter values Tip: Use the following shortcuts for quick setup: • Hold the ∧ button while powering on to lock or unlock the transmitter.
Shure Incorporated Locking the Interface Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon appears on the home screen when the interface lock is enabled. 1. From the Utilities menu, navigate to Locks and select one of the following lock options: ◦ None: The controls are unlocked ◦ Power: The power switch is locked ◦ Menu: The menu parameters are locked ◦ All: The power switch and menu parameters are locked 2. Press O to save.
Shure Incorporated Shure Rechargeable Batteries Shure lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50% capacity in one hour and reach full charge within three hours. Single chargers and multiple bay chargers are available to recharge the Shure batteries. Caution: Only charge Shure rechargeable batteries with a Shure battery charger.
Shure Incorporated Battery Installation ① Accessing the Battery Compartment Press the door latches and open the battery door. ② Inserting the Battery Insert the battery, contracts first into the battery compartment. Press down on the tab to fully seat the battery, and then close the battery door. Tip: To remove the battery, pull up on the tab on the bottom of the battery. ADX1 SB910 Battery Runtime Note: Higher RF power levels decrease battery runtime.
Shure Incorporated Tips for Editing Menu Parameters • To access the menu options from the home screen, press O . Use the arrow buttons to access additional menus and para meters.
Shure Incorporated Power Higher RF power settings can extend the range of the transmitter. Note: Higher RF power settings decrease battery runtime. Output Sets the RF output to On or Mute. ◦ On: RF signal is active ◦ Mute: RF signal is inactive Audio Menu Pad Adjust the pad to avoid overloading the audio input. Select 12 dB or Off. Offset Adjust Offset level to balance mic levels when using two transmitters or when assigning multiple transmitters to receiver slots. Adjustment range: -12 dB to +21 dB.
Shure Incorporated ◦ Power: The power switch is locked ◦ Menu: The menu parameters are locked ◦ All: The power switch and menu parameters are locked Link Info Displays the following information about the link between a transmitter and receiver: ◦ Not Linked: The transmitter is not linked to a receiver ◦ Linked: The transmitter is linked to a receiver. Select Unlink? to free the transmitter from the receiver link.
Shure Incorporated Note: The receiver band must match the band of the transmitter. 1. 2. 3. 4. 5. Select a receiver channel. Tune the channel to an available frequency using group scan or manually turn to an open frequency. Power on the transmitter. Press the SYNC button on the receiver. Align the IR windows between the transmitter and the receiver so that the IR LED illuminates red. When complete, Sync Success! appears. The transmitter and receiver are now tuned to the same frequency.
Shure Incorporated Tip: The clip can removed and rotated 180 degrees to increase mounting options. RF Mute RF Mute prevents transmission of the audio by suppressing the RF signal, while allowing the transmitter to remain powered-on. The home screen displays RF MUTED in this mode. 1. From the Radio menu, navigate to Output. 2. Choose one of the following options: ◦ On: RF signal is active ◦ Mute: RF signal is disabled 3. Press O to save.
Shure Incorporated Safe Start menu options: • RF: Mute or On • Locks: None, Pwr, Menu, All Use the navigation buttons to make changes. Tip: To exit the Safe Start menu, cycle the power or momentarily remove the battery. Note: Previous settings for locks and RF will be retained when the transmitter is powered on in Safe Start. Input Overload The OVERLOAD message appears when the audio input experiences a highlevel signal. The power LED turns red as an addi tional indicator of an overload.
Shure Incorporated Tone Generator The transmitter contains an internal tone generator that produces a continuous audio signal. The tone is helpful when conduct ing a sound check or for troubleshooting the audio signal chain. The level of the tone is adjustable from -60 dB to 0 dB and the frequency can be set to 400 Hz or 1000 Hz. Tip: Always start with the level set to -60 dB to avoid overloading speakers or headphones. 1. From the Audio menu select Tone Gen. 2. Set the frequency to 400 Hz or 1000 Hz. 3.
Shure Incorporated Updating Firmware Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are devel oped to incorporate additional features and enhancements. To take advantage of design improvements, you can upload and in stall new versions of the firmware by using the Shure Update Utility. The Shure Update Utility is available for download from http://www.shure.com/.
Shure Incorporated Operating Temperature Range -18°C (0°F) to 45°C (113°F) Note: Battery characteristics may limit this range. Storage Temperature Range -29°C (-20°F) to 74°C (165°F) Note: Battery characteristics may limit this range. Audio Input Connector 4-Pin male mini connector (TA4M) or Lemo Connector Configuration Unbalanced Impedance 4-Pin male mini connector (TA4M) 910 kΩ Lemo Connector 8.2 kΩ Maximum Input Level 1 kHz at 1% THD Pad Off 8.5 dBV (7.5 Vpp) Pad On 20.
Shure Incorporated High Density Mode 125 kHz varies by region Modulation Type Shure Axient Digital Proprietary Power 2 mW, 10 mW, 40 mW See Frequency Range and Output Power table, varies by region ShowLink Network Type IEEE 802.15.4 Antenna Type Zigbee Dual Conformal Frequency Range 2.40 to 2.
Shure Incorporated LEMO Frequency Bands and Transmitter RF Power Band Frequency Range (MHz) RF Power (mW)*** G53 470 to 510 2/10/40 G54 479 to 565 2/10/20 G55† 470 to 636 2/10/40 G56◇ 470 to 636 2/10/40 G57△ 470 to 616* 2/10/40 G62 510 to 530 2/10/40 H54 520 to 636 2/10/40 K53† 606 to 698 2/10/40 K54△ 606 to 663** 2/10/40 K55 606 to 694 2/10/40 K56 606 to 714 2/10/40 K57 606 to 790 2/10/40 K58 622 to 698 2/10/40 L54 630 to 787 2/10/40 R52 794 to 806 10 JB 8
Shure Incorporated K55 606-694 MHz Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich A, B, BG, CH, CY, CZ, D, DK, EST, F * FIN, GB, GR, H, HR, I, IRL, IS, L, LT * M, N, NL, P, PL, RO, S, SK, SLO, TR * all other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated K57 606-790 MHz Country Code Frequency Range Code de Pays Gamme de frequences Codice di paese Gamme di frequenza Código de país Gama de frequencias Länder-Kürzel Frequenzbereich A, B, BG, CH, CY, CZ, D, DK, EST, F * FIN, GB, GR, H, HR, I, IRL, IS, L, LT * M, N, NL, P, PL, RO, S, SK, SLO, TR * all other countries * * This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
Shure Incorporated Canada Warning for Wireless This device operates on a noprotection, nointerference basis. Should the user seek to obtain protection from other radio ser vices operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Econom ic Development Canada’s document Client Procedures Circular CPC2128, Voluntary Licensing of LicenceExempt LowPow er Radio Apparatus in the TV Bands.
Shure Incorporated Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
