SL NITRO 510C RGB & W LED Strobe Luminaire
Showline Offices Dallas 10911 Petal Street Dallas, TX 75238 Tel: +1 214-647-7880 Fax: +1 214-647-8030 Auckland 19-21 Kawana Street Northcote, Auckland 0627 New Zealand Tel: +64 9 481 0100 Fax: +64 9 481 0101 Asia Unit C, 14/F, Roxy Industrial Centre No. 41-49 Kwai Cheong Road Kwai Chung, N.T., Hong Kong Tel: +852 2796 9786 Fax: +852 2798 6545 Europe Rondweg zuid 85 Winterswijk 7102 JD The Netherlands Tel: +31 (0) 543-542516 www.philips.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual IMPORTANT INFORMATION Warnings and Notices When using electrical equipment, basic safety precautions should always be followed including the following: a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b. Do not use outdoors. c. Do not mount near gas or electric heaters. d. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. e.
Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire TABLE OF CONTENTS Showline Offices..................................................................................................................................... Insdie Front Cover IMPORTANT INFORMATION Warnings and Notices......................................................................................................................................................... 1 Additional Resources for DMX512..............................
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual RGBW Expanded Mode ........................................................................................................................................................... RGBW Expanded Mode (Zones).............................................................................................................................................. RGBW 16-Bit Mode......................................................................................
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual PREFACE 1. About this Manual The document provides installation and operation instructions for the following products: • SL NITRO 510C LED STROBE Luminaire Please read all instructions before installing or using this product. Retain this manual for future reference. Additional product information and descriptions may be found on the product specification sheet.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual SL NITRO 510C LED STROBE LUMINAIRE OVERVIEW 1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual LCD Display / Menu System Edit a Preset Edit a Chase Home (menu settings) DMX512 Addressing Return to Main Screen LCD Display To rotate menu 180 degrees from current orientation, press and hold the two center buttons for 2 seconds.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual INSTALLATION AND SET UP 1. Power Requirements The SL NITRO 510C LED STROBE Luminaire operates on AC input voltages from 100 to 240 VAC. WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely remove power from unit when not in use. AC Power Operation When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging).
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 2. Connecting Power Units can be powered in one of two ways: • Direct connection to a AC power source using an AC input cable. For wiring of AC input connector, refer to "Connecting SL NITRO 510C LED STROBE Luminaires to AC Power" on page 8. • Connection from the AC output of another SL NITRO 510C LED STROBE Luminaire. When using this method, it is very important not to connect any other type of equipment device.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 3. Connecting to the DMX512 Network Basic DMX512 installation consists of connecting multiple SL NITRO 510C LED STROBE Luminaires together (up to 32 luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX connector on the first SL NITRO 510C LED STROBE Luminaire.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual provided M9 holes. It is recommended (and may be required by local and national safety codes) to use and install a safety cable (sold separately). When hanging the fixture, be sure to leave enough space around the luminaire to allow proper, uninterrupted airflow for cooling and positioning. SAFETY CABLE: Is sold separately and recommended for all hanging installation and may be required by national and local codes.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Connecting Luminaires Top-to-Bottom Each SL NITRO 510C LED STROBE Luminaire includes two built-in Quick Connect slot and pin systems as illustrated in Figure 8. This allows a quick connection of units when stacked on top of each other. Up to twenty SL NITRO 510C LED STROBE Luminaires may be supported when connected using the Quick Connect system. Side View 1 Locking Mechanism Locking Mechanism Pin Step 1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Connecting Luminaires Side-to-Side Each SL NITRO 510C LED STROBE Luminaire ships with three Luminaire Connecting Pins as indicated in Figure 9. All three pins are used to connect two luminaires together linearly. Each fixture must be mounted using its own mounting hardware. The side-to-side pins are only to align the luminaires and do not provide hanging support.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Connecting Combined Luminaires Top-to-Bottom When combining units connected top-to-bottom, two SL NITRO 510C LED STROBE Luminaires are first connected end-to-end and then connected top-to-bottom with a single SL BAR 520 luminaire. Connecting Notes: WARNING! Do not exceed 10 rows of combined luminaires connected together top-to-bottom with a single hanging point.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual vent the spacing between the two SL NITRO 510C LED STROBE Luminaires from spreading apart at the center. Obtain and install: SL BAR 520 LED Luminaire SL NITRO 510C LED STROBE Luminaires See detail below SL NITRO 510C LED STROBE Luminaires Nut Bolt Lock Washer Flat Washer Note, hardware shown available from others. 1) One M10-1.5 x 25 mm Long, Hex Head Cap Bolt 2) One 10 mm Flat Washer 3) One 10 mm Split-Lock Washer 4) One M10-1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Connecting Combined Luminaires Side-to-Side When combining units connected side-to-side, all units connect using the same pin system and any combination can be created (refer to installation instructions and warnings contained in "Connecting Luminaires Side-to-Side" on page 12). • Each SL NITRO 510C LED STROBE Luminaire and SL BAR 520 RGBW Luminaire ships with three Luminaire Connecting Pins as indicated in Figure 9.
Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire OPERATION AND PROGRAMMING 1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual .
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Step 7. The preset is now saved and can be recalled via the menu or DMX. Effects Effects are chases stored values of the luminaire's LED settings that can be recalled via the menu system or DMX. There are 10 factory defined chases and eight user adjustable chases. You can adjust the master intensity, speed, and fade values for any of the 18 chases.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Note: The Level 3 PIN will always unlock all functions. Table 4: Security Lock Levels Lock Level Level 1 Menu Functions Affected Edit Presets, Edit Chases, and Settings Menu Level 2 Settings Menu Level 3 All Use the Up and Down buttons to select security PIN codes. Press the Check button and then use Left and Right and Up Down buttons to assign the pin code. Press the Check button to save the new PIN code.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the fixture's DMX settings. When finished, press the Check button to exit the menu level. The adjustable parameters are described in Table 8. Table 8: DMX Setting Parameters Parameter DMX Enable Description • Enable - Fixture will respond to DMX commands/signals. • Disable - Fixture will ignore DMX commands/signals.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Quick Selection Buttons The Showline menu system includes four quick selection buttons on the top of the menu. These keys provide direct access to common functions and act as shortcuts to main menu items as described in Table 9. Table 10: Quick Select Buttons Quick Select Button Description Main Menu Refer to Settings/General for more information. Edit a Preset Refer to Recalling or Editing Presets for more information.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 5. Dimming Curve Selection Through the menu, you are able to select one of four dimming curves: • Linear Curve • PL_Curve • S_Curve • Square Curve Lumen Output PL_Curve * Lumen Output Linear Curve 0 DMX Value 0 DMX Value *PL Curve follows the dimming curve of Philips Selecon PL series LED luminaries.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 6. Master / Slave Operational Mode The Master / Slave Operational Mode allows one SL NITRO 510C LED STROBE Luminaire to act as the "Master" unit and all other connected units are controlled by this unit. When a unit is set to "Slave" mode, it will only listen to and follow any commands sent from a "Master" unit. Only one "Master" unit is allowed in this type of operation. To setup a master / slave network: Step 1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual DMX CONTROL 1. RGB & W Operation The SL NITRO 510C LED STROBE Luminaire operates either as an RGB or White strobe, with the two engines operating separately from each other. It is not possible to utilize both RGB and White values to create a combined output of the two systems.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 11: DMX Channel Mapping (RGBW Full Mode) CONTINUED FROM PREVIOUS PAGE 3 Color Presets 0 - 255 0 - 100% 0 Preset 7 DMX 19 - 20 Preset 8 DMX 21 - 22 Preset 9 DMX 23 - 24 Preset 10 DMX 25 - 26 Preset 11 DMX 27 - 28 Preset 12 DMX 29 - 30 Preset 13 DMX 31 - 32 Preset 14 DMX 33 - 34 Preset 15 DMX 35 - 36 Preset 16 DMX 37 - 38 Preset 17 DMX 39 - 40 Preset 18 DMX 41 - 42 Preset 19 DMX 43 - 44 Preset 20 DMX 45 - 46 Preset 21 DMX 47 - 48 Pr
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 11: DMX Channel Mapping (RGBW Full Mode) CONTINUED FROM PREVIOUS PAGE 3 Color Presets 0 - 255 0 - 100% 0 Chase1 DMX 202 - 204 Chase2 DMX 205 - 207 Chase3 DMX 208 - 210 Chase4 DMX 211 - 213 Chase5 DMX 214 - 216 Chase6 DMX 217 - 219 Chase7 DMX 220 - 222 Chase8 DMX 223 - 225 Chase9 DMX 226 - 228 Chase10 DMX 229 - 231 User Chase1 DMX 232 - 234 User Chase2 DMX 235 - 237 User Chase3 DMX 238 - 240 User Chase4 DMX 241 - 243 User Chase5 DM
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 11: DMX Channel Mapping (RGBW Full Mode) 8 Zone 1 - 6 Intensity 9 Red 1 - 6 - High 10 Red 1 - 6 - Low 0 - 255 0 - 100% 0 8-bit control for the intensity of the Zones - 0 to 255 (full) 0 - 65535 0 - 100% 0 16-bit control of Red LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit control of Green LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit control of Blue LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit control of
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 4. RGBW Full Mode (Zones) Table 12 provides DMX channel mapping of all DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is operated in various Groups (Zones) Control Mode when set to RGBW Full Mode. Table 12: DMX Channel Mapping (RGBW Full Group Modes) Note: Refer to previous DMX mapping information for Color Presets, Strobe, Duration, Intensity Timing, Color Timing, and Control channels.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 5. RGBW Expanded Mode Table 13 provides DMX channel mapping of the DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is in RGBW Expanded DMX512 mode (as set by the luminaire’s menu system).
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 13: DMX Channel Mapping (RGBW Expanded Mode) CONTINUED FROM PREVIOUS PAGE 3 Color Presets 0 - 255 0 - 100% 0 CF_27_Lighter Blue DMX 123 - 124 CF_28_Cyan DMX 125 - 126 CF_29_Marine Blue DMX 127 - 128 CF_30_Soft Green DMX 129 - 130 CF_31_Moss Green DMX 131 - 132 CF_32_Green DMX 133 - 134 CF_33_Fem Green DMX 135 - 136 CF_34_JAS Green DMX 137 - 138 CF_35_Pale Green DMX 139 - 140 CF_36_Spring Yellow DMX 141 - 142 CF_37_Yellow DMX 143 -
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 13: DMX Channel Mapping (RGBW Expanded Mode) Control channel operation. Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 6. RGBW Expanded Mode (Zones) Table 14 provides DMX channel mapping of all DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is operated in various Groups (Zones) Control Mode when set to RGBW Expanded Mode. Table 14: DMX Channel Mapping (RGBW Expanded Group Modes) Note: Refer to previous DMX mapping information for Color Presets, Strobe, Duration, Intensity Timing, Color Timing, and Control channels.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 7. RGBW 16-Bit Mode Table 15 provides DMX channel mapping of the DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is in RGBW 16-Bit DMX512 mode (as set by the luminaire’s menu system).
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 15: DMX Channel Mapping (RGBW 16-Bit Mode) CONTINUED FROM PREVIOUS PAGE 3 Color Presets 0 - 255 0 - 100% 0 CF_27_Lighter Blue DMX 123 - 124 CF_28_Cyan DMX 125 - 126 CF_29_Marine Blue DMX 127 - 128 CF_30_Soft Green DMX 129 - 130 CF_31_Moss Green DMX 131 - 132 CF_32_Green DMX 133 - 134 CF_33_Fem Green DMX 135 - 136 CF_34_JAS Green DMX 137 - 138 CF_35_Pale Green DMX 139 - 140 CF_36_Spring Yellow DMX 141 - 142 CF_37_Yellow DMX 143 - 1
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 15: DMX Channel Mapping (RGBW 16-Bit Mode) Control channel operation. Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 8. RGBW 16-Bit Mode (Zones) Table 16 provides DMX channel mapping of all DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is operated in various Groups (Zones) Control Mode when set to RGBW 16-Bit Mode. Table 16: DMX Channel Mapping (RGBW 16-Bit Group Modes) Note: Refer to previous DMX mapping information for Color Presets, Strobe, Duration, Intensity Timing, Color Timing, and Control channels.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 9. RGBW 8-Bit Mode Table 15 provides DMX channel mapping of the DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is in RGBW 8-Bit DMX512 mode (as set by the luminaire’s menu system).
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 17: DMX Channel Mapping (RGBW 8-Bit Mode) CONTINUED FROM PREVIOUS PAGE 2 Color Presets 0 - 255 0 - 100% 0 CF_27_Lighter Blue DMX 123 - 124 CF_28_Cyan DMX 125 - 126 CF_29_Marine Blue DMX 127 - 128 CF_30_Soft Green DMX 129 - 130 CF_31_Moss Green DMX 131 - 132 CF_32_Green DMX 133 - 134 CF_33_Fem Green DMX 135 - 136 CF_34_JAS Green DMX 137 - 138 CF_35_Pale Green DMX 139 - 140 CF_36_Spring Yellow DMX 141 - 142 CF_37_Yellow DMX 143 - 14
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 17: DMX Channel Mapping (RGBW 8-Bit Mode) Control channel operation. Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 10. RGBW 8-Bit Mode (Zones) Table 18 provides DMX channel mapping of all DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is operated in various Groups (Zones) Control Mode when set to RGBW 8-Bit Mode. Table 18: DMX Channel Mapping (RGBW 8-Bit Group Modes) Note: Refer to previous DMX mapping information for Color Presets, Strobe, Duration, Intensity Timing, Color Timing, and Control channels.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 11. 6-Channel Mode Table 19 provides DMX channel mapping of the DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is in 6-Channel DMX512 mode (as set by the luminaire’s menu system).
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 19: DMX Channel Mapping (6-Channel Mode) CONTINUED FROM PREVIOUS PAGE 2 Color Presets 0 - 255 0 - 100% 0 CF_27_Lighter Blue DMX 123 - 124 CF_28_Cyan DMX 125 - 126 CF_29_Marine Blue DMX 127 - 128 CF_30_Soft Green DMX 129 - 130 CF_31_Moss Green DMX 131 - 132 CF_32_Green DMX 133 - 134 CF_33_Fem Green DMX 135 - 136 CF_34_JAS Green DMX 137 - 138 CF_35_Pale Green DMX 139 - 140 CF_36_Spring Yellow DMX 141 - 142 CF_37_Yellow DMX 143 - 144
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 19: DMX Channel Mapping (6-Channel Mode) Control channel operation. Set control channel value to desired action, hold value for at least 5 seconds, then turn to 0. Set control channel value to 0 without any scaling.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 12. Mapping 16-Bit Mode Table 20 provides DMX channel mapping of the DMX512 control values when the SL NITRO 510C LED STROBE Luminaire is in Mapping 16-Bit DMX512 mode (as set by the luminaire’s menu system). Note: When using pixel mapping software with the SL NITRO 510C LED STROBE Luminaire, it is suggested to only map the RGB channels and utilize the white channels independently. Refer to "RGB & W Operation" on page 24 for more information.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 20: DMX Channel Mapping (Mapping 16-Bit Mode) 41 Red 6 - High 42 Red 6 - Low 43 Green 6 - High 44 Green 6 - Low 45 Blue 6 - High 46 Blue 6 - Low 47 White 6 - High 48 White 6 - Low 0 - 65535 0 - 100% 0 16-bit control of Red 6 LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit control of Green 6 LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit control of Blue 6 LEDs from 0 to full 0 - 65535 0 - 100% 0 16-bit con
Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire 14. Strobe Rate DMX Timing Detail The chart below describes the Strobe Rate DMX parameters of the SL NITRO 510C LED STROBE Luminaire. Note: Continuous ON Mode illuminates all LEDs without strobing. This feature is activated when Strobe Rate and Strobe Duration are both set to DMX value 255.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 15. Strobe Duration DMX Timing Detail The chart below describes the Strobe Duration DMX parameters of the SL NITRO 510C LED STROBE Luminaire.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual 16. SL NITRO 510C LED STROBE Luminaire RDM Parameter IDs The following tables outline and describe all the RDM parameters IDs associated with SL NITRO 510C LED STROBE Luminaires.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 23: SL NITRO 510C LED STROBE Luminaire RDM Parameters IDs Get Allowed Set Allowed RDM Parameter IDs Value Comment Implemented ■ DEVICE_INFO 0x0060 ■ PRODUCT_DETAIL_ID_LIST 0x0070 ■ DEVICE_MODEL_DESCRIPTION 0x0080 ■ ■ MANUFACTURER_LABEL 0x0081 ■ ■ ■ ■ DEVICE_LABEL 0x0082 ■ ■ ■ FACTORY_DEFAULTS 0x0090 ■ ■ LANGUAGE_CAPABILITIES 0x00A0 LANGUAGE 0x00B0 ■ SOFTWARE_VERSION_LABEL 0x00C0 ■ BOOT_SOFTWARE_VE
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 23: SL NITRO 510C LED STROBE Luminaire RDM Parameters IDs Get Allowed Set Allowed RDM Parameter IDs Value ■ ■ PERFORM_SELFTEST 0x1020 SELF_TEST_DESCRIPTION 0x1021 ■ CAPTURE_PRESET 0x1030 ■ PRESET_PLAYBACK 0x1031 ■ ■ Comment Implemented Table 24: SL NITRO 510C LED STROBE Luminaire RDM Manufacturer Status IDs Manufacturer Specific messages are in the range of 0x8000 - 0xFFDF.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual Table 26: SL NITRO 510C LED STROBE Luminaire RDM Manufacturer Specific PIDs for Sub Device Get Allowed Set Allowed RDM Parameter IDs Type Length Unit Prefix Min Max Default Description Manufacturer Defined PIDs range is 0x8000-0xffdf. See Table A-3, ANSI E1.
Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire CLEANING AND CARE WARNING! All cleaning should be performed with power completely removed from the luminaire. Never remove protective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when cleaning the fixture. All service and maintenance, other than described herein, should be performed by a qualified technician or Authorized Service Center. 1.
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual TECHNICAL SPECIFICATIONS 1.
