SB-5688AK INSTRUCTION MANUAL 8x8 HDMI UHD 4K2K Capable Matrix Routing Switch w/ EDID Management, ARC and Auxiliary Audio Input & Output 4K2K Capable
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS HDMI-AUDIO MATRIX SWITCHER SERIES Thank you for purchasing the SB-5688AK HDMI Matrix Switch with Auxiliary. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMI Matrix switcher. CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 PACKAGE CONTENTS .................................................. 2 FEATURES ...............................
PACKAGE CONTENTS & FEATURES PACKAGE CONTENTS Check that you have the following components: • SB-5688AK Matrix Switcher • Ethernet & RS-232 V2.0 Protocol Instructions • Master wireless IR Remote Control (SW-HD88AK) • 19 inch Ear mount bracket (Part # 1U-440L) • SB-100 IR Extender distance ~984 feet (300M) Receiver set • SB-100C IR Extender distance 6ft (2M) Receiver Cable • CD Contents : This manual, Windows GUI, ISP V1.
SPECIFICATIONS SPECIFICATIONS • Type of HDMI Switcher: 8x Inputs to 8x Outputs HDMI Matrix Switch with Audio and Extension • HDMI Support: HDMI 4K2K, 1080p@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats • HDCP/CEC Support: HDCP 2.0 Compliant, CEC Compliant • Video Bandwidth: Double Data Rates: 340MHz, Total 6.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving power. The switcher will remember the last setting during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. STATUS DISPLAY Front panel status display shows current matrix routing configuration. This same display also shows particular configuration settings depending on your current function.
FRONT PANEL-ARC FRONT PANEL-ARC 9. FUNCTION KEY - ARC Audio Return Channel (ARC) is a feature that sends audio from the TV back down the HDMI cable to its source device, in this case, the switcher, Not all displays support ARC; check your Users Guide for additional information. ( Default = ARC Disabled ) The “Audio & ARC” port can support audio from either of three sources. If the Input Video/Audio Source is HDMI, the audio can extracted from the embedded signal.
FRONT PANEL-AUX FRONT PANEL- AUX 10. FUNCTION KEY - AUX (The audio additional on the “Audio / ARC” port ) The AUX FUNCTION feature allows you to replace the embedded HDMI audio signal with an audio signal that is connected to the switchers Audio AUX Input. Using the AUX function replaces the audio and does not mix the audio. (Default = AUX Disabled) To Enable the AUX option on a specific Output, perform the follow steps: - Press the AUX button.
FRONT PANEL-EDID-ALL-OFF-LOCK-ENTER FRONT PANEL-EDID 12. FUNCTION KEY - EDID (1) Used to display change current EDID mode. - Press EDID to select new EDID mode or select - Press SOURCE row #1 or #2 Select EDID modes. - Press ENTER to ready memory location. - Or press EDID again to cancel operation. Operation completes. Note : Operation will abort if no keys are pressed within 5 seconds. FRONT PANEL-ALL-OFF-LOCK-ENTER 13. FUNCTION KEY - ALL 14. FUNCTION KEY - OFF 15.
FRONT PANEL-RECALL-MEMORY FRONT PANEL-EDID 17. FUNCTION KEY - RECALL The system will show previously stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Press RECALL button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER The pre-set configuration will execute. Operation completes. Note: Operation will abort if no keys are pressed within 5 seconds.
BACK PANEL-SWITCH CONTROLS BACK PANEL-SWITCH CONTROLS 1. DC POWER INLET: The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive). Power Socket: DC Jack - inner OD Ø 2.1mm (+ ) Outside OD Ø 5.5mm (GND) Power input - 12VDC, 5A 2. IR EXTENDER CONTROL: Support one of IR Extender.
BACK PANEL-HDMI Input / Output BACK PANEL-HDMI Input / Output 5. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI: Connect a HDMI signal source link of HDMI source direct HDMI digital video/audio to this Female HDMI connector. This HDMI port support HDMI and DVI digital video sources. If you remove the HDMI screw post, use the provides ISO screw to keep the internal HDMI jack secure. Removing the HDMI Screws without installing the ISO screws will void your warranty.
REMOTE CONTROL Before making any connections to the switcher, observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC Standard) HOW TO SETUP IR CODES : POWER ON : 01FC A15E CUSTOM CODE : 01FC POWER OFF : 01FC A25D ARC : AUX : RECALL : ENTER : MEMORY : 01FC 01FC 01FC 01FC 01FC 01FC 01FC 01FC 01FC B847 LOCK : 9966 EDID : B24D ALL : B34C OFF : B44B B54A B748 B04F B14E PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 01FC DESTINATION #2 : 01FC DESTINATION #3 : 01FC DESTINATION #4 : 01FC DESTINATION #5 : 01FC DESTINATION #6 : 01FC DES
EDID FUNCTION EDID function for HDMI Matrix Switcher EDID Setup To Change the EDID Setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION EDID function for HDMI Matrix Switcher Mode 5 . H36-3D-M (1080p-36 bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH Mode 6 . 4K2K (24/30Hz) HDMI Support : 4K2K-3D, PCM 2CH (3860x2160-24/30Hz) Audio Support: PCM 2CH Mode 7 . 1920x1200-60Hz (DVI-D) DVI Support : DVI-D 1920 x 1200 60Hz LEARNING EDID Learning EDID from Destination to Source Learning EDID Setup 1.
EDID FUNCTION Learning EDID Single to Single Example : Learn Destination #8 EDID To Source #5. Step 1. Press EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2. Press the Destination #8 button row Copy the Destination #8 Display EDID. Step 3. Press the Source #5 button row Learning the Destination #8 EDID to Source # 5. Step 4. Press ENTER button To confirm entries.
EDID FUNCTION-PASS MODE The PASS feature is part of a firmware update released after JUNE 2014. If you do not see the PASS feature then you do not have the latest firmware. You should contact your place of purchase for availability of a firmware update. Note all devices are eligible for this firmware update. Firmware update requires a PC with OS Windows XP or WIN7 and an RS-232 port (or USB to RS-232). Customer is responsible for implementing a firmware update and accepts all risks.
TYPICAL APPLICATION INSTALLING DIAGRAM Samples connection : Using Switch IR External port, RS-232 or Ethernet command to control Switcher SB-5688AK via one PC or SB-100 IR receiver transmit the SB-5688AK’s IR signal. NOTE: 1. Switcher IR External port : Use SB-100 IR signal Receiver. 2. Control Switch via a PC RS-232. 3. Control Switch via a PC Ethernet. Application RS-232, IR and Ethernet control the Switcher. INSTALLING DIAGRAM Samples connection : 1.
IR EXTENDER IR EXTENDER 1. SB-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) Distance: Max.300M IR Receiver (SB-100) IR PN#: SW-5669 R oHS /95/E C IR E XT. in RS - 232 IR EXT .
IR EXTENDER IR EXTENDER 1. SB-101 IR 300M Transmitter Device DC 12V Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set SB-101 Maximum Distance ~ 984 feet (300M) 2.
ETHERNET & RS-232 SERIAL INTERFACE ETHERNET SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.