ELITE PELLET GRILL OWNER'S MANUAL AND ASSEMBLY INSTRUCTIONS Model#: SRPG16006XL 5009725 CERTIFIED TO UL SUBJECT 2728-2009 CERTIFIED TO ULC/ORD- C2728-13 Refer to Intertek’s Directory of Building Products for detailed information
TABLE OF CONTENTS WARNINGS………………………………………...…………………………….......2-3 EXPLODED VIEW & PARTS LIST……………………………………………………4-7 HARDWARE AND TOOLS………………………….................................................. 8 ASSEMBLY IN STRUCTIONS…………………………………………………...… 9-19 CONTROLLER TOUCH PAD INSTRUCTIONS………………………………..…... 20 PREPARATION FOR USE & LIGHTING INSTRUCTIONS……………....…… 21-22 SHUT DOWN INSTRUCTIONS .............................................................................23 OPERATING INSTRUCTIONS………………………………………….
WARNINGS IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL ! IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL, PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! ! BEFORE ASSEMBLING AND OPERATING YOUR GRILL, READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY.
WARNINGS ! WARNING Use only a Ground Fault Interrupt (GFI) protected circuit with this grill. Only use a properly-grounded power source. Do not alter or remove the grounding plugs on the power cord or household outlet. Never move the grill while it is operating, or when it contains hot pellets or ashes. Always open the grill lid carefully. The heat and stream inside grill body is hot.
EXPLODED VIEW-A 1 2 30 49 29 25 24 23 3 22 4 21 28 26 27 5 20 6 48 7 19 8 17 9 16 18 10 11 12 13 14 15 4
EXPLODED VIEW-B 31 47 32 46 33 45 34 44 35 43 36 42 37 38 40 39 41 Digital Control Wiring Diagram NOTE: The fuse is located on the back of the controller.
PARTS LIST Warming Rack Bracket Chimney Cap 2 Hopper-Top Side Handle Protection Guard Cooking Grate 3 Utensil Hook 5 Warming Rack 1 Power Cord Bracket Hopper Gasket Hopper-Bottom Assembly Flame Tamer Front Shelf Bracket L Cooking Chamber Front Left Leg Grease Tray Wagon Wheel 2 Wheel Axle 1 Chamber Lid Temp Gauge Back Left Leg Hopper Inner Bottom Shelf Hopper-Top Gasket Front Shelf Hopper-Bottom Grease Bucket Caster Circuit Board Box 2 Rubber Sealer Front Right Leg PTC controller Back
PARTS LIST 41 Hopper Bottom Panel 46 Grill Probe 42 Auger 47 Power Cord 43 Auger Housing 48 Front Shelf Bracket R 44 Firepot 49 Meat Probe 45 Hot Rod 7
HARDWARE AND TOOLS Hardware # Description Picture Qty AA M4 Cap Nut 1 BB M6 x 12 Bolt 36 CC M5 x 10 Bolt 8 DD M6 x 14 Step Bolt 1 EE M4 x 8 Bolt 1 FF M6 Nut 26 GG M12 Lock Nut 2 TOOLS REQUIRED Phillips Head Screwdriver (Not included) Adjustable Wrench (Not included) 8
ASSEMBLY INSTRUCTIONS Choose a suitable, clear area for assembly. Ask a friend for help as some parts are heavy or difficult for one person to hold and assemble. To help protect the smoker’s finish, cover the area with cardboard. Step 1 Remove the lid from the cooking chamber by removing bolt and washer and sliding the hinge pins on the lid out of the hinge holes on the cooking chamber. Set bolt and washer aside for Step 18. Step 2 With the help of a friend, place the cooking chamber (#27) on its side.
ASSEMBLY INSTRUCTIONS Step 3 Insert the bottom shelf (#12) into the mounted legs. Attach remaining two legs ("Back Right" (#17) & “Back Left" (#11) by inserting the hooks of the bottom shelf (#12) into the holes in the legs before bolting to the cooking chamber (#27) using (8) M6 x 12 bolts (BB) and (8) M6 nuts (FF). Tighten all leg hardware. Note: Bottom shelf (#12) must be mounted before securing remaining two legs.
ASSEMBLY INSTRUCTIONS Step 5 With assistance,position the assembly upright as figure shown. Step 6 Attach chamber right bracket (#19) onto cooking chamber (#27) right endcap inside by (2) M6 x 12 bolts (BB) and (2) M6 nuts (FF) as figure shown. Attach side handle (#22) on cooking chamber (#27) right endcap by (4) M6 x 12 bolts (BB) and (4) M6 nuts (FF).
ASSEMBLY INSTRUCTIONS STEP 7 Attach chimney pipe (#20) and chimney gasket (#18) to the cooking chamber (#27) right endcap using (4) M6 x 12 bolts (BB). Be certain the gasket fits between the chimney pipe and outside face of the chamber endcap as figure shown. 20 Gasket 18 Hardware Used BB M6 x 12 Bolt BB 4pcs Step 8 Screw chimney cap (#21) into chimney pipe (#20) top as figure shown by turning it clockwise. Do not screw chimney cap all the down.
ASSEMBLY INSTRUCTIONS Step 9 Connect the hopper top (#2) to the hopper bottom assembly (#6) with (4) M5 x 10 bolts (CC). Install protection guard (#3) into the hopper assembly with (2) M5 x 10 bolts (CC). Note: Insert all 6 bolts before tightening completely. CC Hardware Used CC 2 3 M5 x 10 Bolt 6pcs 6 Step 10 Attach the power cord bracket (#4) to the back of the hopper assembly with (2) M5 x 10 bolts (CC).
ASSEMBLY INSTRUCTIONS STEP 11 Slide hopper gasket over auger housing. Then place the pellet hopper assembly onto the cooking chamber (#27) by inserting the auger housing through the left endcap. While holding the hopper assembly away from the endcap, insert the grill probe (#46) through the endcap wall. The grill probe (#46) should be turned horizontal, as shown in the figure. Tighten the grill probe (#46) into place using (1) M4 x 8 bolt (EE) and (1) M4 cap nut (AA).
ASSEMBLY INSTRUCTIONS Step 12 Attach the front shelf bracket L (#7) to the front of the cooking chamber (#27) near the left leg using (2) M6 x 12 bolts (BB) and (2) M6 nuts (FF). Connect front shelf (#13) to front shelf bracket R (#48) by inserting the shelf hooks through the bracket. Then insert the left side of the shelf through the left shelf bracket on the cooking chamber. Attach the front shelf bracket R (#48) to the front of the cooking chamber (#27) using (2) M6 x 12 bolts (BB) and (2) M6 nuts (FF).
ASSEMBLY INSTRUCTIONS S te p 14 Place the grease tray (#28) on the chamber right side bracket and chamber left side bracket as figure shown. 28 Left side Right side Tray should fit into slots on chamber left bracket. Step 15 Place cooking grates (#23) onto cooking chamber grid brackets/rails as figure shown.
ASSEMBLY INSTRUCTIONS Step 16 Insert warming rack brackets (#1) into mounting tabs found on cooking chamber endcaps. 1 Step 17 Place warming rack (#25) onto warming rack brackets (#1) so that it securely rests in bracket.