ASSEMBLY INSTRUCTIONS Step 18 Reconnect the cooking chamber lid (#29) by sliding the hinge pins into the hinges. Secure it with the washer and bolt removed in Step 1. Screw the temperature gauge (#30) fully into the lid. Adjust the orientation and lock the gauge into position using the pre-attached nut. If desired, install the utensil “S” hooks onto the side handle. When needed, connect the meat probe to the controller by inserting the femal plug into the controller socket marked “Meat Probe”.
ASSEMBLY INSTRUCTIONS ELITE Pellet Grill (Assembled) 19
CONTROLLER OVERVIEW NOTE: CONTROLLER OVERVIEW POWER BUTTON MODE SELECTOR LED DISPLAY SCREEN WIRELESS CONNECTION INDICATOR MEAT PROBE SOCKET 888F SENSOR SELECTOR TEMPERATURE SELECTOR TEMPERATURE ADJUSTMENT Mode Selector: Used to toggle between Cook and Smoke modes. Temperature Selector: Used to toggle between the current grill temperature, indicated as “ACTUAL” and the desired cooking temperature, indicated as “SETPOINT”.
PREPARATION FOR USE & LIGHTING INSTRUCTIONS ! PLACE THE SMOKER OUTDOORS ON A HARD, LEVEL, NON-COMBUSTIBLE SURFACE AWAY FROM ROOF, OVERHANG OR ANY COMBUSTIBLE MATERIAL. NEVER USE ON WOODEN OR OTHER SURFACES THAT COULD BURN. PLACE THE SMOKER AWAY FROM OPEN WINDOWS OR DOORS TO PREVENT SMOKE FROM ENTERING YOUR HOUSE. IN WINDY WEATHER OR RAINY WEATHER, PLACE THE SMOKER IN AN OUTDOOR AREA THAT IS PROTECTED FROM THE WIND AND RAIN. ! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR SMOKER.
PREPARATION FOR USE & LIGHTING INSTRUCTIONS Step 6 Plug the power cord into a properly grounded 110 V electrical outlet. DO NOT use if the ground tip has been removed from the power cord. DO NOT use an extension cord or ungrounded outlet. Step 7 Press the power button to start the grill. By default, the grill will start in grill cooking mode with a a set point temperature of 350 F. Step 8 Observe the auger turning as pellets fill the tube.
LIGHTING INSTRUCTIONS & SHUT DOWN LIGHTING INSTRUCTIONS MANUAL METHOD 1. With the grill properly setup and located for operation, plug the power cord into a 110 V grounded electrical outlet. (Refer to SETUP PROCEDURE for more information.) DO NOT use if the ground tip has be removed from power cord. DO NOT use an extension cord or ungrounded electrical outlet. 2. Open the grill lid. Remove the warming rack, cooking grids, grease tray and flame tamer. 3.
OPERATING INSTRUCTIONS CURING THE SMOKER Before initial use, it recommended to cure the smoker to remove manufacturing oils or paint residue and minimize smoke odors or unnatural flavors from being added to food. Follow “Set Up Procedure” to ensure the grill is safe for operation. Follow “Lighting Instructions” to start the grill, then enter Cook mode. Set the temperature to 250 F and allow to operate for 2 hours. Increase the temperature to 400 F and allow to operate for an additional hour.
OPERATING INSTRUCTIONS COOKING INSTRUCTIONS Using the “SET ADJ” up or down arrow buttons, set the desired grilling temperature. The temperature adjusts in 5 degree increments and will be displayed on the LED Display. NOTE: 600 F temperature setting is recommended to only be used for cleaning. However, in colder weather, it might be used for cooking to overcome the ambient temperature. Once the desired temperature is set, press “Temp” to “ACTUAL” to display the current grill temperature.
OPERATING INSTRUCTIONS POST COOKING INSTRUCTIONS After grilling or smoking your food, allow the grill run on the highest temperature setting for several minutes. Doing so will burn off excess juices and help clean the grill. Press “Mode” to quickly set the grilling temperature to 600 F. With lid closed, allow the grill to operate 5 to 15 minutes, depending on what was cooked, or the amount of residue/grease on the grids. Turn OFF the grill (refer to “Shut Down Instructions”).
OPERATING INSTRUCTIONS Using the “SET ADJ” up or down arrow buttons, set the desired smoking temperature. The temperature will be displayed on the LED Display. Once the desired temperature is set, press “Temp” to “ACTUAL” to display the current temperature measured by the meat probe. When the meat probe temperatures reaches the desired set point, a beeping alarm will sound. ! IMPORTANT: Keep the meat probe as clean and dry as possible. Clean with a damp, soapy cloth.
WIRELESS CONNECTION THE PTC APP You can connect your phone to the grill’s controller using Bluetooth® wireless technology. First, you will need to install the PTC app from either the App Store or Google Play on your smartphone. Precision Temperature Control smartphone app Upon opening the PTC app, you will need to create an account by simply inputting an email address or phone number and create a password.
WIRELESS CONNECTION THE PTC APP Using the App To enter shutdown mode and power off the grill, simply press the power button icon. This will start the pre-programmed shutdown process for the controller. Any time during the smoking or grilling process, you may look at a chart that shows the data of the temperature curve. It is only a simple chart for a glance of the temperature performance. Caution: Changes or modifications not expressly approved by Shinerich Industrial Ltd.
GRILLING TIPS GRILLING TIPS & CLEANLINESS If you pre-cook meat or poultry, do so immediately before grilling. Never defrost meat at room temperature or on a countertop. Refrigerate leftovers within 2 hours of taking off the grill. Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw meat, uncooked poultry or seafood.
CARE AND MAINTENANCE CARE AND MAINTENANCE Cleaning the Grill Body Use warm, soapy water to clean the inside and outside of the grill body with a cloth and then wipe it dry. Treat the interior surface of grill body with a light coat of vegetable oil and then wipe it dry periodically to prevent rusting. DO NOT use oven cleaners, abrasive cleaners or abrasive cleaning pads on the surface of the grill body.
CARE AND MAINTENANCE Customer Service (866) 814-0585, Monday through Friday from 8 a.m. to 8 p.m. EST ! DO NOT RETURN the appliance to the store. Contact Customer Service for assistance first. ! WARNING: Always disconnect the electrical cord prior to inspecting, cleaning, maintenance or service work. ! NEVER perform any inspection, cleaning, maintenance or service on a HOT GRILL.
TROUBLESHOOTING Command Center will not turn ON Display Code: EU-1 Electrical connection failure. Check cord plugged into GFCI outlet. Verify wiring connections are firmly connected. Blown fuse on circuit board. Replace fuse found on back of circuit board. GFCI outlet tripped. Reset GFCI breaker. Overheating due to fire Unplug the power cord and allow grill to cool. or excess pellet fuel in Remove excess pellets from fire pot, if any, and fire pot. inspect all components for possible damage.
TROUBLESHOOTING Grill will not reach or Grill will not reach or maintain set temperature maintain set temperature Inspect the Combustion/Cooling Fan is operating properly. Ensure the air intake on the hopper housing is not blocked and the fan blades are clean. Verify the Hopper has enough pellet fuel for operation. Insufficient wood pellet fuel Verify the wood pellets are dry. Grill will not light automatically Ensure “Probe” button is set to “Grill” and “Temp” button is set to “Actual”.
TROUBLESHOOTING Control Board Wiring Diagram M FAN MOTOR 120VAC IGNITOR 8 AUGER MOTOR O W R Y P B FUSE GRILL RTD MEAT PROBE CONTROLLER (BACK VIEW) COLOR CODE: B . . . . BLACK O . . . . ORANGE P . . . . PURPLE R . . . . RED W . . . .WHITE (COMMON) Y . . . . YELLOW NOTE: A cartridge located on the back of the control board houses a 5 amp, 120 volt fast blow fuse. If any electrical issues occur (short circuits or power surges), inspect this fuse. Replace when necessary.
WARRANTY INFORMATION This appliance has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer/purchaser that all aspects of this product will be free of defects in material and workmanship for one year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. Defects or damage caused by the use of other than genuine parts are not covered by this warranty.
