Figure 3-37 Brightness 3.2.5.3 Backup Restore Table 3-25 Backup Restore ICON ITEM & FUNCTION 1. You can backup/restore system to/from flash disk or inserted memory card. (A. Disk on Chip, B. CF Card, C. SD Card) ( Figure 3-38) 2. When you launch this AP, it must check backup file in DOC first. And if you select other storage, it will check again. 3. Then if it has the file, appeared its date behind “Last backup date:”; if not, disable “Restore Now” Button. 4.
Figure 3-38 Backup Restore Figure 3-39 Backup & Restore Start Figure 3-40 Backup OK Figure 3-41 Restore OK 3.2.5.
F8 Information ü To assign your favorite application program to Hot Keys. ü ü Choose one of Hot Keys from pull-down list.(Figure 3-43) To tap “Browse…” inside “Assign program” applet. Select one application program you want from program list, then, ü choose “OK”. (Figure 3-43) To tap “Default” to return back to default setting. (Figure 3-42) ü Figure 3-42 Fn-Key Settings Figure 3-43 Fn-Key Settings 3.2.
3.2.7 Dialing Properties Table 3-28 Dialing properties ICON ITEM & FUNCTION l “Dialing Properties” Tab :( Figure 3-44) ü In the When dialing from list, select the “Location” where you want to change settings.(Figure 3-45) To create a new location, select “New”. Enter the name of the location, and then select “OK”.(Figure 3-46) Enter or edit the area code and local country code as needed. ü ü ü ü In Dial using, select “Tone dialing” or “Pulse dialing”. Most phone lines are tone.
Figure 3-44 Dialing Properties Figure 3-45 Dialing Properties Figure 3-46 Dialing Properties Figure 3-47 Dialing Properties 3-34
3.2.8 Display Properties Table 3-29 Display properties ICON ITEM & FUNCTION l “Background” Tab :( Figure 3-48) ü From the “Image” list, select an image you want as the background of the desktop.(Figure 3-49) To locate an image in another folder, select “Browse”.(Figure 3-50) To have the image cover the entire background, select “ □ Tile ü ü image on background” l “Appearance” Tab(Figure 3-51) ü Change the color scheme :( Figure 3-52) Ø Ø From the” Scheme” list, select a scheme.
Figure 3-50 Display properties Figure 3-51 Display properties Figure 3-52 Display properties 3.2.9 Input Panel Table 3-30 Display properties ICON ITEM & FUNCTION l “Input panel” Tab :( Figure 3-53) ü Select the input method you want to change. ü To change the Soft Keyboard Options , tap “Option” (Figure 3-54) .
l “Options” Tab : ü Change the soft keyboard options as desired, selecting from: Large or small keys Using gestures for space, black-space shift, and enter. Ø Ø ü ü To exit the soft keyboard Options, press “OK” on the control bar, or press the key on the keypad. To exit the Input Panel, press “OK” on the control bar, or press the key on the keypad. . Figure 3-53 Input Panel Properties Figure 3-54 Input Panel Properties 3.2.
l “Security” Tab (Figure 3-57) Modify the security settings as desired. You can enable any of the following by tapping the checkbox: Ø Allow cookies Ø Allow TLS 1.0 security Ø Allow SSL 2.0 security Ø Allow SSL 3.0 security Ø Warm when switching across secure and insecure areas. ü l “Advanced” Tab (Figure 3-58) ü Modify the security settings as desired.
Figure 3-57 Internet Settings Figure 3-58 Internet Settings 3.2.11 Keyboard Table 3-32 Keyboard ICON ITEM & FUNCTION l “Repeat” Tab :( Figure 3-59) ü To change the amount of time between depressions before ü ü repetition starts, adjust the Repeat delay slider To change the repeat rate, adjust the Repeat rate slider. Test your new setting. ü Tap “ OK” to exit the “Keyboard” Tab.
Figure 3-59 Keyboard Properties 3.2.12 Network and Dial-up Connections Table 3-33 Network and Dial-up Connections ICON ITEM & FUNCTION l “Connection” Tab : ü To create a “Dial-up Connection”: Double-tap the “Make New connection”. In the “Make New Connection” dialog box, enter a name for the connection. Ø Ø Ø Ø Ø Ø Ø Select “Dial-Up Connection”. Select the “Next” button. Select the modem you want use. Select “Configure” Under “Connection Reference”, use the default settings provided.
Ø Select “TCP/IP Settings”. In the “General” tab, ensure “Use Server-assigned IP address” is selected. In the “Name Servers” tab, ensure “Use Server-assigned addresses” is selected, and select “OK”. If you are unable to connect with these default settings, see your ISP or network administrator for specific TCP/IP information. Select the “Next” button and type the telephone number. Ø Select the “Finish” button.