User Manual

ManualsBrandsShin Chuan Computer ManualsElectronicsPortable Data Terminal

Ø Select “TCP/IP Settings”. In the “General” tab, ensure “Use

Server-assigned IP address” is selected. In the “Name

Servers” tab, ensure “Use Server-assigned addresses” is

selected, and select “OK”. If you are unable to connect with

these default settings, see your ISP or network administrator

for specific TCP/IP information.

Ø Select the “Next” button and type the telephone number.

Ø Select the “Finish” button.

The connection you just created appears as an icon in the “Network

and Dial-up Connections” folder.

ü Set up a point-to-Point Protocol(PPP) account with an ISP and

obtain the following information:

Ø Access telephone number

Ø User name

Ø Password

Once you have established an account, create a new connection on

your device. When creating this connection, you should be able to use

all of the default TCP/IP settings provided in the Make New

Connection Wizard. If you can’t connect using the default settings,

contact your ISP or access your ISP’s Web site for specific TCP/IP

information as well as primary and secondary DNS address.

ü Modify connection setting

Ø Select Start > Settings > Network and Dialup Connections

Ø Select the icon for connection settings you want to modify.

Ø Select File > Properties, or double- tap the appropriate icon.

Ø Select desired options. There may be additional settings that

depend on the connection. To modify, select the icon and

select the icon and select Advanced Settings… from the

menu.

Summary of content (10 pages)

PAGE 1
Select “TCP/IP Settings”. In the “General” tab, ensure “Use Server-assigned IP address” is selected. In the “Name Servers” tab, ensure “Use Server-assigned addresses” is selected, and select “OK”. If you are unable to connect with these default settings, see your ISP or network administrator for specific TCP/IP information. Ø Select the “Next” button and type the telephone number. Ø Select the “Finish” button.
PAGE 2
Figure 3-60 Network and Dial -up Connections Figure 3-61 Network and Dial -up Connections Figure 3-62 Network and Dial -up Connections Figure 3-63 Network and Dial -up Connections 3-42
PAGE 3
Figure 3-64 Network and Dial -up Connections Figure 3-65 Network and Dial -up Connections Figure 3-66 Network and Dial -up Connections Figure 3-67 Network and Dial -up Connections 3-43
PAGE 4
Figure 3-68 Network and Dial -up Connections Figure 3-69 Network and Dial -up Connections Figure 3-70 Network and Dial -up Connections Figure 3-71 Network and Dial -up Connections 3.2.
PAGE 5
l “Identification” Tab : (Figure 3-74) ü l “Network Fill in or edit ID”the Tab: data(Figure as desired. 3-75) To have displayed youname startyou youruse device, Enter thethis userinformation name, password, andwhen domain to log select “Display Owner Identification” at Power On. on to remote network. To set up identification for remote networks, see Setting up identification for remote networks. ü ü Figure 3-72 Owner Properties Figure 3-73 Owner Properties 3.2.
PAGE 6
Figure 3-74 Password Properties 3.2.15 PC Connection Table 3-34 PC Connection ICON ITEM & FUNCTION l “PC Connection” Tab : (Figure 3-77) ü Select the first checkbox to enable direct connections to the desktop computer. (Figure 3-77) Tap the “Change Connection… ” button to modify the connection method from USB or Serial. (Figure 3-78) To exit the “Change Connection” dialog, press “OK” from the control bar, or press the key on the keypad.
PAGE 7
Figure 3-75 PC Connection Figure 3-76 PC Connection 3.2.16 Power Table 3-35 Power ICON ITEM & FUNCTION l “Battery” Tab : (Figure 3-79) ü Provide change level indicators for Main battery and Backup battery. Provide remaining power capacity of main battery. If a “Main Batteries very Low” warning message shows, the remaining battery life is around 30 minutes to SC600 shuts down.
PAGE 8
ü ü ü l The Scheme Tab allows you to determine the time to switch state to Suspend mode when using either Battery Power or AC Power. Select Battery Power or AC Power as the power scheme from the pull-down list.( Figure 3-80) Select the time to suspend mode from the pull-down list.
PAGE 9
Figure 3-79 Power Figure 3-80 Power Figure 3-81 Power 3.2.17 Regional Settings Table 3-36 Regional Settings ICON ITEM & FUNCTION l “Region” Tab : (Figure 3-84) ü Select the desired location/language. Review the Appearance samples in the bottom half of the screen. Select the Tab at the top for any settings you wish to change, Options to modify include Number, Currency, Time, and Date.
PAGE 10
Figure 3-82 Regional Settings 3.2.18 Remove Programs Table 3-37 Remove Programs ICON ITEM & FUNCTION l “Remove Programs” Tab : ü Only user installed programs can be removed. Select the program you wish to remove from the list and press “remove” button.