58MM Portable MINI Thermal Printer Instruction Manual
Version Feb, 2016 Notice • All rights reserved. Reproduction of any part of this manual in any form whatsoever, without manufacturer’s express permission is forbidden. • The contents of this manual are subject to change without notice. • All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, manufacturer would greatly appreciate being informed of them.
Notes on safety This section presents important information intended to ensure safety and effective use of the printer. Please read carefully. Be sure to use the specified battery and power source provided by our company. Connection to an improper power source may cause fire , explosion or damage to the printer. Don’t put the battery into the fire or water, don’t disassemble or modify the battery, don’t be short circuit, otherwise may result in injury or fire even explosion.
power adapter. 8、In order to ensure print quality and longevity of your printer, please ensure that only good quality thermal paper rolls are used. 9、Please keep this manual in a safe place, where it can be accessed easily and used for your reference. 1.
2.Specification Printing Method: Direct Thermal Speed: 90mm/sec Reliability TPH Life: 100km Resolution: 203DPI (8dot/mm) Printing Width: 48mm (384dot) Paper Width: 58± 01mm Roll Diameter: φ≤40mm Paper Type: Thermal Paper Power: rechargeable lithium battery/NI-MH battery Battery: 7.2VNiMh, 700mAh Charging method: external charger Print parameters: support to download the Logo trademark, support bar-code print.
agreement (optional)/Android up to 4.0 operation system. Driver: Win200/Win2003/Win2000/Win7/WinXP/VISTA/WIN8/LINUX Working Temperature: -10～50℃ ; Humidity: 10～90% Weight: 192g 3.Appearance Model:5805 Size:107*7951.
4.Communication Interface 1. RS232(COM)：standard RS232 Communications Protocol 2. Bluetooth 2.0：standard Bluetooth 2.0 Communications Protocol 3. USB：standard USB Communications Protocol 4. Two-mode Bluetooth: General Bluetooth2.0 / 4.0 Communication Protocol 4-1.
However, the printer usually works only on receiving data, it doesn’t have to respond anything back to the host , then TXD signal can be ignored , and then the connection can be sampled as following: Printer Host RXD TXD GND GND 4-2.
2-----2400 8------115200 3-----4800 9------230400 4-----9600 A------460800 5-----19200 B------921600 6------38400 C------1382400 For example, if you want to change baud rate to 115200bps, please send string “AT+BAUD8”. 4-2-3. Build connection. 1. Turn on the printer; 2. Search for the Bluetooth device with host device; 3. If there are other Bluetooth devices, please select “LY58”(for example) printer; 4. Enter default pairing code “1234” 5. Pairing succeed. 4-3.
5.The installation of the paper roll The printer use 58MM thermal paper, and adopt to easy paper loading. So the paper is very convenient install. Paper diameter Max 40mm. Thermal paper installation method is as follows: （1） Open the printer top cover （2） Thermal Paper as follow Graph to put into paper storehouse （3）Put out a little of the paper outside printer,then close the top cover.
Under the normal working status, the paper feeding begins when the printer paper feed press 【FEED】 button, and stop when loosen【FEED】 button. Power off the printer, then hold down the【FEED】button and The printer Self test press the power button at the same time. Wait 2 seconds ,then loosen the【FEED】button,the current setting will be printed out. Power off the printer, then hold down the【FEED】button and Transformation in both English press the power button at the same time.
6.
Step 4: - Find this icon and open it.click on the "Connect Printer" after the connection successfully, click on the "Print Test Page", the printer will work. If you use the "USB", "Step 2" into the corresponding communication, set "BluetoothDEMO" from "USBDEMO".
7.Operating Manual for IOS APP 1.
2. Turn on the Apple mobile Bluetooth , then click “Printer-X”: (Image 2) 3.
4. Connect successful, put content into Edit Box to test printing.
8.The Bluetooth configuration Step1: Make sure your device (like PC, Note Book) has Bluetooth function, then once the Bluetooth for your device is activated, you will see the Bluetooth sign showed in the right bottom side of your device(like PC) screen. Step2:Power on the Bluetooth printer.
Step4:if you can see screen as below,then the device is searching the bluetooth printer,please wait.
Step5:Once the Bluetooth printer is found.
Step6:Choose “Let me choose my own passkey”, then enter “1234”(this is factory default passkey, if you want to change it, you have to inform us to set the new passkey for you in our factory before shipping),then click “Next”. Step7:if you can see the screen as below, that means the Bluetooth printer is already connected. Please notice the assigned COM ports ,then Click”Finish”. (Note: The Bluetooth device will automatically assign a COM port.
Step8: Now if you want to test if the printer is OK to print, you could use a com tool , and send printed data to Outgoing COM port( just as above image shown: COM5). (Com tool setting is 9600,N,8,1.
9.How to use the port of USB 1.Insert the CD-ROM,click on the file(58/80 series printer driver software )to star to installation ,select the language appears as you need to install the driver,as shown below: 2.Then select the language click “OK”,as shown below ,click”Continue”to next step. 3.
shown below: 4.Click :N ext”after the operation in the below figure(Customer can also modify the path of the driver can choose the default installation path) 5.
antivirus software ,appears to block the installation of the windows allow this operation. 6.
7.
8.
If the printer prints a normal page, then it shows that the work was successful.
Note: If the printer prompts "Print Error", please return to the "port" option from the "USB001" started trying to choose 10.Serial (COM) port to be used 1.
2.
Click "Apply" again. 3.
If the printer prints a normal page, then it shows that the work was successful.
11.Cleaning of printer head Cleaning of printer When the printer has the following conditions, you should clean the printer head: ① The printer does not print clearly and the thermal paper is Ok. ② The printer Print pages length ways is not clear ③ It’s getting too noisy while feeding paper or printing. Printer head cleaning steps are as follows: 1. Power off the printer and open the paper room cover. Remove the thermal paper roll. 2.
12.General Troubleshooting 1: Why serial port printer printing messy code? A: Ensure the baud rate setting in the PC is same as the printer baud rate. ( we can see printer baud rate from self test page) 2: Self printing test is ok,but printer does not work after driver installation. A: Recheck the installation according to above installation wizard and see if we selected the right port or ask service center for advice if needed.
7. Printing speed is very slow for serial printer A: follow this path and change the set accordingly : Driver -- Properties -- Device Settings -- Print Mode -- Print as soft font. 8. Water or other liquid spills into the printer A: Cut off the power,we can dry the main board or printer head with a hair dryer, careful of the temperature ( average 50 degree is ok ) 9. The printer can't open A：The battery maybe without electricity，please use power adapter to charge.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
