Product Card

ManualsBrandsShenzhen zbaitu Technology ManualsElectronicsLaser Engraver

Table Of Contents

空白页面

ZBT_3737O instructions

一、Summary

1. Frame description

 Power interface: connect the power supply to supply power to the machine

 USB interface: connect the computer to transmit data and control the machine through

the computer

 SD card slot: store gcode code to complete offline engraving

 X、Y-axis motor: control the precise movement of the laser to complete the engraving

 Lifting frame: adjust the distance between the laser module and the carved object to

achieve the best focal length

 Laser module: emit laser for engraving or cutting

2. Accessories list

Parts description

USB data cable：To connect to the machine through a computer,

connect one end of the USB data cable to the USB port of the

machine, and the other end to the USB port of the computer.

12V-5A Power Adapter：To use the machine, connect the adapter

to the machine's power interface, connect the plug to the adapter,

and insert the adapter into an AC power outlet.

axis motor

USB interface

Power interface

SD card slot

Laser module

Lifting frame

Summary of content (20 pages)

PAGE 1
ZBT_3737O instructions 一、Summary 1.
PAGE 2
protection goggle：Do not look directly at the laser while the engraving machine is working. If you want to observe the engraving situation and process, please wear protective glasses SD card + SD card reader: used for offline engraving 二、Assemble the machine 1.
PAGE 3
screw M3*8 2 Stainless steel gasket M5*14*1 4 2. Assembly steps 1.
PAGE 4
2. Column integral frame 3.
PAGE 5
4. Wear the timing belt 5.
PAGE 6
. Clip YR shaft wire into profile groove 7.
PAGE 7
8.
PAGE 8
9.
PAGE 9
PAGE 10
11.
PAGE 11
2. Connect the software Connection mode 1 (wired): 1. Turn on the machine power 2. Connect one end of the data cable provided by us to the USB port of the machine and the 3. other end to the USB port of the computer Open the computer operating software and click the connect button to connect Connection mode 2 (Bluetooth): 1. 2. 3. 4. 5. Turn on the machine power Open the WIFI connection list of mobile phone or computer Select the network "GRBL_ESP", password: 123456789.
PAGE 12
PAGE 13
4. 5. 6. a) Set the broadcast mode bit -Bluetooth After the setup is completed, restart Turn on the computer, look for bluetooth 【btgrblesp】, and connect. Open the operating software, select the corresponding serial port and click the connect button to connect Connection mode 3(WIFI_AP mode): 1. 2. 3. 4. Turn on the machine power Open the WIFI connection list of mobile phone or computer Select the network "GRBL_ESP", password: 12345678.
PAGE 14
PAGE 15
6. a) Set WiFi name b) Set WiFi password c) Set that address of the control panel in the same segment of the route d) Set Telnet parameters After the setting is completed, restart, then open the browser and enter the IP address of the controller in the address bar ("192.168.31.127" in the example) to open the Web control interface Third, matters needing attention 1. safety matters 1. 2. 3. 4. 5. 6. 7.
PAGE 16
30W, 40W-PRO adjustable focus module, the distance between the lens and the sculpture is 20-40 mm.
PAGE 17
MDF board 18mm √ √ × Balsa 8mm √ √ √ Hard wood 18mm √ √ × Acrylic 8mm(Dark Color) √ √ √ Brushed Acrylic(Transparent) √ × × Corrugated cardboard < 8mm √ √ √ Kraft Paper 0.5mm √ √ √ Paperboard 2mm √ √ √ Weeding invitation paper 0.
PAGE 18
TSLD80W_FF45_PRO Material Plywood 5mm Marking √ Craving √ Cutting √ Plywood 8mm √ √ √ Plywood 18mm √ √ √ MDF board 5mm √ √ √ MDF board 8mm √ √ √ MDF board 18mm √ √ √ Balsa 8mm √ √ √ Hard wood 18mm √ √ √ Acrylic 8mm(Dark Color) √ √ √ Brushed Acrylic(Transparent) √ × × Corrugated cardboard < 8mm √ √ √ Kraft Paper 0.5mm √ √ √ Paperboard 2mm √ √ √ Weeding invitation paper 0.
PAGE 19
Bakelite √ √ × Brushed Glass √ × × Cobblestone √ × × Brushed Ceramic √ × × Printed Metal √ × × PCB borad √ × × Anodized Aluminium √ × × Brushed Stainless Steel √ × × Mirror Stainless Steel √ × × Gold × × × Cutting Speed Material Plywood 2mm TSLD40W_XX_PRO 160mm/min，S1000,1Pass TSLD80W_FF45_PRO 480mm/min，S1000,1Pass Plywood 3mm 120mm/min，S1000,1Pass 480mm/min，S1000,1Pass Plywood 4mm 100mm/min，S1000,1Pass 480mm/min，S1000,1Pass Plywood 5mm 120mm/min，S1000,2Pass
PAGE 20
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.