User's Manual

Production Introduction:
1
名称： TNS-0117说明书
材质： 100g书写纸
尺寸： 展开尺寸：225x150mm 成品尺寸：75x150mm
颜色： 单黑双面印刷 三折页
设计师： 温宇姣 2020.10.24
版本号： KC TNS-0117 2010 V1
this controller is of Bluetooth wireless type, which is
mainly used with N-S console. The aisle light of the
controller is assigned through the console. This
product is available in motor vibration and sensor
functions, and it supports the connection to PC
console via USB so as to achieve PC XINPUT function.
Product Diagram:
2
This product should be well kept when not in use.
This product cannot be used and stored in humid
environment.
This product should be used or stored by avoiding
dusts and heavy loads to guarantee its service life.
Please do not use the product which is soaked,
crashed or broken and with electrical performance
problems caused by improper use.
Do not use external heating equipment such as
microwave ovens for drying.
If it is damaged, please send it to the maintenance
department for disposal. Do not disassemble it by
yourself.
Children users shall use this product properly under
the guidance of parents, and do not be addicted to
the game.
Matters Needing Attention:
14
Electrical Parameters:
10
The wired N-S and PC XINPUT mode connection is
supported.
It is automatically identified as N-S mode when
connected to N-S console.
It is in XINPUT mode when connected to PC.
Note: the above are test data of battery voltage 4.10V
USB Connection Function:
9
The 3D joystick is not required to be calibrated manually
on N-S console. The 3D joystick will be calibrated
automatically when the N-S console is plugged.
If the 3D joystick drips during use, please replug and
unplug the controller before use. Be careful not to touch
the 3D joystick when you plug and unplug the controller.
3D Joystick Instruction:
11
Enter into the “N-S console setting – controller and
inductor – calibration of gyroscope inductor” for
controller test and calibration; place the controller
horizontally on the desktop and long press + or – for
calibration.
Gyroscope Calibration Instruction:
12
3 gears in total: weak, intermediate and strong (the
changed amplitude is 40%, 70% and 100%) regulation
methods:
Lowest gear (40% amplitude): press 4 L/ZL/R/ZR keys on
the side for 1 sec simultaneously, then the regulations is
successful.
Intermediate gear (70% amplitude): press 4 L/ZL/R/ZR
keys on the side for 1 sec simultaneously, then the
regulations is successful.
Top gear (100% amplitude): press 4 L/ZL/R/ZR keys on
the side for 1 sec simultaneously, then the regulations is
successful.
The intermediate gear of controller vibration is
acquiescently connected for the first time, i.e. 70%
amplitude.
Motor Vibration Regulation:
8
Semi-automatic TURBO function setting: press TURBO
key and then set it as the TURBO function key as
required, then you can complete the settings successfully.
Full-automatic TURBO function setting: press TURBO key
and then press the key which has been set up with the
semi-automatic TURBO function.
Keys available for TURBO function settings: A key, B key,
X key, Y key, + key, - key, L key, R key, ZL key, ZR key,
“cross” key (up, down, left and right), L3 key (left 3D joystick
press key) and R3 (right 3D joystick press key).
Clear TURBO function keys that have been set:
Clear TURBO function of single key: press TURBO key + key
set up with TURBO function for quick clear.
Shut down the automatic firing function: you should short
press the – key and down arrow key once, and the
controller will vibrate once to execute the command, then
the automatic firing function of all keys will be turned off.
Regulation methods of automatic firing speed:
A. Increase automatic firing speed: short press T key and up
arrow key once, and the controller will vibrate once to
execute the command, which means that the automatic
firing speed has been up regulated by one gear successfully.
B. Reduce automatic firing speed: short press T key and up
arrow key once, and the controller will vibrate once to
execute the command, which means that the automatic
firing speed has been down regulated by one gear
successfully.
C. The automatic firing function is memorable. If the
console is connected after the controller is disconnected,
the automatic firing speed set up previously can be
memorized.
TURBO Function Settings:
7
During the charging of the controller: the charging
LED indicator light will be on, and it will be off after
the controller is fully charged.
Charging Indication and Charging
Characteristics:
5
Connect N-S mode: the N-S console screen is
off or shut down, and the controller automatically
disconnects and switch to sleep mode.
Bluetooth connection mode: the Bluetooth
disconnects and switches to sleep mode after the
Bluetooth code key is pressed shortly.
Without any keys pressed within 5 min, it will switch
to auto sleep mode (including gravitational induction
immobility). Remarks: there is no auto sleep currently.
Auto Sleep:
6
1. N-S wired connection mode:
(1)Before use the wired connection, please confirm
the N-S console system: “set up” -> “controller and
inductor” -> “wired connection of Pro controller” in
“on” state.
(2)The controller is connected to the N-S base via
USB cable so as to be used as the wired controller,
and the corresponding indicator light of the controller
will flash slowly; when you plug out the USB cable,
the controller turns into wireless mode and connect
the console automatically!
2. N-S wireless connection mode:
(1)Before use the wireless connection, please confirm
that the N-S console system turns to: “controller” -> “
change grip/order” in pairing state.
(2)Long press the code key of the controller for 3
seconds to enter into Bluetooth search mode, and
the LED indicator light will flash in marquee type.
The corresponding channel indicator light will be on
after successful connection.
3. PC-360, PC mode:
Firstly, please download the PC 360 to Windows
computer. After the PC 360 is installed, the controller
should be connected to the computer via USB cable,
and the corresponding channel indicator light will be
on after successful connection. The LED2 and LED3
will be on when the No.1 and No.10 keys are pressed
simultaneously to switch to PC mode.
4. Back connection and shutdown instruction:
(1)Short press the Bluetooth code key to shutdown
the controller.
(2)Press Home to wake up the controller. The
awakened controller will automatically back connect
the console which has been paired previously; it will
switch to auto sleep if the back connection is not
successful within 8 seconds.
Mode and Pairing Instruction:
4
Function Diagram:
3
Item
Working voltage
Working current
Sleep current
Vibration current
Reference value
DC 3.6-4.2V
24mA
22.5uA
Vibration current
Battery capacity
Operating distance
82 mA~130 mA
Input power DC 4.5~5.5V/400mA
500mA
10m
Appearance patent number: 202030476822.3
User Manual
Product No.: TNS-0117 Version Number: A1.1
Left 3d joystick
Print Screen key
HOME key
- key
T key
A key
Y key
X key
B key
+ key
Right 3d joystick
Direction key
Bluetooth code key
Function Name
Is there a
function?
Remarks
USB wired connection Yes
Bluetooth connection Support
Connection mode N-S PC mode
Six-axis gravity induction Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
A key
B key
X key
Y key
- key
+ key
L key
R key
ZL key
ZR key
Home key
Print Screen key function
3D joystick (left 3D joystick
function)
L3 key (left 3D joystick press
key function)
R3 key (right 3D joystick press
key function)
Cross key function
TUBRO speed regulation function
Connecting indicators
Motor vibration intensity
adjustment
Controller upgrade Support
If this product cannot be used due to system
compatibility and other reasons, please contact the
customer service provider to provide program: install
the upgrade package to upgrade.
Specific operation: plug the controller into the computer
first, then press the X+Y+HOME for 3 sec to enter into the
upgrade mode; and then open the Program.exe
software, click update firmware to upgrade, and wait for
the prompt for successful update.
Controller Upgrade Instruction:
13
ZR key
R key
TYPE-C charging interface
L key
ZL key
h