Safety and Product Information It may result in death or serious injury in case of failure to avoid the following potential dangerous situations. Warnings Health Warning •Please consult your doctor before starting or changing your exercise program. If you wear a pacemaker or other electronic device that is implanted into your body, consult your doctor before using YUNMAI Fit HR.
consent of YUNMAI. In addition, YUNMAI reserves the right to refuse warranty applications for products and services that have been acquired and/or used in violation of any state law. Warranty and remedies herein are exclusive, and replace all other expressed or implied or statutory warranty conditions, including any liability derived from the merchantable and applicable warranty of any commodity under some special purpose, laws and regulations or other circumstances.
④ Wristband bracelet Worn on the wrist. First Activation Pull the bracelet out and connect the bracelet USB interface to your computer's USB socket or outlets with USB interface to activate the screen by charging for the first time. Wearable Device You can wear YUNMAI Fit HR on your left wrist or right wrist. Attention: please do not damage the heart rate sensor behind the device.
obtain no heart rate for various reasons. However, you can help YUNMAI Fit HR achieve the most consistent and reliable readings with some attempts. Just fine Too loose If the YUNMAI Fit HR will slide on your The YUNMAI Fit HR should be comfortably wrist, or sensor cannot read the heart attached to your wrist. rate, try to tighten the strap slightly. Download YUNMAI APP You can download the YUNMAI Fit HR official APP by scanning the following QR code. APP downloaded via other channels may be unusable.
① Open “My Device” and find the ② Please ensure that the screen is corresponding bracelet. bright and the bracelet is away from other ones after enterig the search page. ③ Click the "YUNMAI" touch button to ⑤ End of the binding. confirm binding the device. Note: cellphone Bluetooth setting is not required for YUNMAI Fit HR, direct Bluetooth pairing via YUNMAI APP. Unbinding Open the “my device” and find the bound bracelet.
IOS Unbound: 1. Enter the bracelet setup 2. Enter the mobile phone setup, open page, select “Unpair”, and click [OK] to the Bluetooth, find the YUNMAI Fit HR unbound device. and click the icon [ ]. Ignore this device. Android unbind: enter the bracelet setup page, select “Unpair” and click [OK] to unbound device. Icon Functions Display the current time and date. It will automatically adjust the time when the device is synchronized with the phone. Display your current heart rate.
Display the total day consumtion of calories, including the basal metabolic rates and calories consumed by activities. Monitor your daily activity time. Alarm mode Step counting mode Sedentary mode, regular reminder Current usage of power Step Count and Goal A target step is generated by YUNMAI Fit HR based on the activity you set, and the device displays the progress of your target when walking. You will be rewarded when you achieve your goals, which keeps your energy alive every day.
the heart rate sensor fits the wrist, and it can measure the heart rate data after 3 seconds' standing. Current heart rate Sleep Monitoring The equipment will test the sleep status when you are asleep, which includes the counting of total sleep hours and sleep quality. The sleep quality data is available in YUNMAI APP.
Note: The actual listed products shall prevail for the functional content outlined in this page, which may be changed without notice. Do Not Disturb You can use this mode during breaks or movies to turn off the vibration mode. Note: The device will automatically enter the Do Not Disturb mode within the set time in the YUNMAI APP account when the " " appears.
Synchronous Data Data can be synchronized regularly through the device to the YUNMAI APP, and also to the phone manually at any time. 1. Keep the distance between the device and the phone within 2 meters, and turn on Bluetooth. 2. Turn on the YUNMAI APP to automatically synchronize data to the phone. Charging Your Device Note: in order to prevent the charging interface from corroding, please ensure that the metal interface of the device and charger and the surrounding area are dry before charging. 1.
• • • Please rinse it entirely after contact with chlorine, saline water, sun cream, cosmetics, ethyl alcohol or other stimulating chemicals. Do not store the device in extreme temperatures for a long time, which may result in the permanent damage. Scrub by using wet towel or hot towel, and then the dry towel.
• If the Bluetooth can’t connect occasionally, iOS phone should turn on Bluetooth in setting, ignore binding bracelet device, and re-open YUNMAI APP for pairing. Bluetooth service of some phones will show abnormality sometimes, it usually can be solved after reopening the Bluetooth or restarting the phone. • How to update bracelet firmware? • Connect bracelet with phone, enter “Me” in YUNMAI APP, click “Device”, and choose “firmware upgrade”.
Wrist strap 〇 〇 〇 〇 〇 〇 Wrist strap buckle 〇 〇 〇 〇 〇 〇 〇: It means the content of toxic and harmful substance in all homogeneous material of the component is less than that stipulated by SJ/T11363-2006. X: It means the content of toxic and harmful substance in at least one homogeneous material of the component exceeds the value specified in SJ/T11363-2006. YUNMAI Fit HR bracelet body and wrist strap both use environmental and safe material.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Product information Product name YUNMAI Fit HR Model D1701NA Main control Nordic chip Sensor: Kionix Heart rate sensor: Silicon labs Si 1142 Wireless bluetooth 4.0 transmissio n Bracelet TPU material Strap size 240X16X10mm Weight: 18g Battery 45mAh capacity: Battery Polymer lithium battery type: Screen 0.86 inch OLED display screen size Working voltage 3.6-4.
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.