Quick Installation Guide

5. Enter AP Mode setup page,choose “Get IP from AC” in connection type, click Next.
6. Enter Wi setup page,set up SSID, Channel, Encryption parameters as below:4.Setup Wizard page,choose AP mode as the current working mode.
(*This QIG uses 4 Antennas dual band AP as an example）
2.By default it is in Fit AP mode, users need click the button at the right corner
to change it to FAT AP mode if needed.
3.In FAT AP mode user interace home page is as shown below:
(2)、After setting the IP address of PC, connect PC with AP in wireless, double-click
"Wireless network Connection", in the pop-up wireless SSID list, select "Wireless
2.4G", click "Connect", then enter the password in the pop-up password dialogue
box, the default password is "66666666", click "OK" to connect.
(1)、Make sure the device is power off
(2)、Follow Figure 1 ,insert clamp hoop into the hole on backside of the enclosure
(3)、Fasten the AP to the pole(diameter 40-60mm) with clamp hoop,after confirming
the angle and direction ,use screwdriver to fix the clamp hoop tightly.
Device installation
Figure 1
Figure 2
Figure 3
(1)、AP connects to the POE port of POE adapter through LAN cable(make sure the
impedence of the LAN cable wires should be less than 6 Ω)
(2)、PC connects to the LAN port of POE adpter through LAN cable
(3)、Power on the POE adapter, POWER LED on the AP should light up normally
(4)、Check networking connection status on PC to verify whether PC is connected
correctly with the AP, see Figure 2.
Hardware connection
(1)、The straight distance should be within the range of AP signal
(2)、Deploy the LAN cable from indoor to outdoor location of AP installation.
The LAN cable should follow 568B standard, and use the network cable tester to test.
(3)、The height of mounting pole should be 1.5M above the roof , the antenna of AP
should face to the base station and in good alignment to make sure signal strength
is the best.
Installation Range
Using the wired connection, set the IP address of the TCP/IP properties of the
wired network card to 192.168.188.X (X is number range of 2-252), and the PC
will be the same IP segment as AP.
(1)、To connect an AP wirelessly, you need set the IP address of the TCP/IP
properties of the wireless network card to 192.168.188.X (X is number range of
2-252) rst, so that the AP and PC in the same IP segment, and set the subnet mask
to 255.255.255.0, as shown in the following picture:
02/Device management01/Device installation
03/ AP Configuration
WEB Login from PC
3.1
Connect PC by wired port
2.2
Connect PC by wireless
2.1
Quick Installation Guide
Outdoor AP
VER 1.0
Input password
Login
Apply Reset Reboot
Information
Settings
IP Address
Subnet
Mac Address
Gateway
AC Address
192.168.188.253
255.255.255.0
44:D1:FA:75:BF:3F
192.168.188.1
172.16.0.1
IP Mode DHCP
Fit AP
Operation Mode AP Mode Fat AP
Uptime 01:05:39
Click Settings
CPU Usage 1%
Memory Usage 20%
0
Device Information
WIFI Information
Device Description LAN Information
IP Mode
Lan IP
Subnet
AC Address
MAC Address
Get IP From AC
192.168.188.253
255.255.255.0
172.16.0.1
44:D1:FA:75:BF:3F
Status
SSID
Channel
Encrypt
MAC Address
ON
Wireless-2.4G
11
Open
44:D1:FA:75:BF:41
Home
Wizard
WIFI
Network
Manage
Flow(2G Wifi)bps
In this mode the AP wireless interface and cable interfac
are bridging together.Without NAT,rewall and all network
related functions.
Gateway Repeater Mode WISP Mode
Current Mode
AP Mode
Home
Wizard
WIFI
Network
Manage
√
1
2
LAN Settings
IP Mode
Get IP From AC
Next
Get IP From AC
Static IP
Get IP From Gateway
AP Mode
1
2
√
2G WIFI Setting
AP Mode
Wi Status
Hide your SSID?
SSID
Wireless2.4G
Channel
Encrypt Open
Timing 1 Day
20M Auto
NextBack