-TX Wireless Flash Controller User Manual 用户手册
Contents General Description . . . . . . . . . . . . . . . . . 1 Conventions used in the manual. . . . . . . . . . . 2 Supported Functions List . . . . . . . . . . . . . . . 3 Name of Parts/LCD . . . . . . . . . . . . . . . . . 4 Name of Parts/Quick Start Guide . . . . . . . . . . . . 5 Preparation Before Use . . . . . . . . . . . . . 6-7 Setting . . . . . . . . . . . . . . . . . . . . . 8-10 Flash awaking and triggering . . . . . . . . . . . 11 The other Trigger Modes . . . . . . . . . . . . .
General Description Thank you for purchase the products of Yongnuo firstly. YN-622N-TX i-TTL wireless flash controller is for supporting the use of YN-622N i-TTL wireless flash trigger transceiver. This product adopts flexible LCD menu control, supporting mixed use of the A/B/C three groups of flashes using i-TTL, manua, or super sync flash mode, can be adjusted the exposure compensation or flash output of each group.
Conventions used in the manual This manual to assume that using the compatible camera/flash, and using the YN-622N transceiver with same channel. Functions supported by the product depend on the camera and flash used. Concerning the operation of YN-622N transceiver, camera and flash , please read the user manual respectively. The latest version of the compatibility list and user manual, firmware, please visit www.hkyongnuo.com. Upgrade to the latest firmware ver sion before using(P15).
Supported Functions List LCD screen display, multi-buttons quick operation The firmware can be upgraded through the USB interface Support wireless shutter release function The focal length(zoom)of the A/B/C three groups of flash can be adjusted separately Equipped with the AF focus assist light (can be disabled) Grouping flash mode: i-TTL/Manual flash/Super sync Supporting mixed use of the A/B/C three groups of flashes with iTTL , Manual flash, or Super sync flash mode The exposure compens
Name of Parts/LCD ※The protective film can be torn out.
Name of Parts/Quick Start Guide A-LCD: Display all the settings of controller, convenient for your view and setup. B-2.5MM Shutter release interface: Wireless shutter release function(P.13). C-AF assist beam emitter: (P.10) D-PC interface: Input the flash sync signal(P.12). E-USB interface: Firmware upgrade through connecting the computer(P.15). F-Mode button: Each time you press the switch in the flash mode(P.8). G-Group button: The arrow shown the switch setting group(P.8).
Preparation Before Use 1. Installing the Batteries Open the cover and install two AA batteries (excluded)according to the marks , rechargeable batteries of 1.2V can be used. Remove the batteries when the product is not used for long time. Please replace the both two batteries at the same time. 2.Installing the Controller on the Camera 1). Unscrew the locking ring of the controller. 2). Slip the mounting foot into the hot shoe of the camera. 3).
Preparation Before Use 4.Channel Setting: Long press the [ZOOM/CH] button, then press the [UP] or [RIGHT] for increasing, press the [DOWN] or [LEFT] for decreasing, press [OK] for confirm. Set the same channel as the YN-622N transceiver. 5. Transceiver and Flash Settings: 1). Set the transceiver’s receiving group, and set the same channel as the YN-622N-TX controller. 2).
Setting 1. Groups and Modes Setting(Remote Control) Shooting with a Different Flash Mode for Each Group 1).Press the [GROUP] button to choose the setup group, press with the arrow to select A/B/C group. 2).Press the [MODE] button to set the flash mode of selected group, each press for the settings as below: TTL: i-TTL Flash, the FEC adjustment range is within -3+3EV, press [LEFT] or [RIGHT] button to increase and reduce 1EV, press [UP] or [RIGHT] button to increase and reduce 0.3EV.
Setting 2. About the Super Sync(SS) Use the non-high speed sync flash to realize higher sync speed, this function is more applicable to strobe flashes whose flash duration is longer, and it is for the camera w h i c h s u p p o r t A u t o F P o n l y. Support setup the time delay parameter of Super Sync. 1.
Setting 3.ZOOM It support the controller setting the the focal length of the flash lamp holder on the transceiver. Each short press the [ZOOM/CH] button, choose one of the A/B/C group, press the [UP] [DOWN] [LEFT] [RIGHT] buttons to setup, supports the range of setup: 24200,AU (automatic), press the [OK] button to confirm. 4. AF Assist Beam Emitter When using AF under low-light, the built-in AF-assist beam emitter of the contorller will be emitted automatically to make it easier to autofocus.
Flash awaking and triggering 1.Flash awaking&Testing flash When half press the shutter button of the camera or press the [TEST] button of the controller , the awaking indicator light of green light will bright, the hot-shoe flash on the transceiver will be awakened. When loosing the [TEST] button, the groups have been selected of flash will be tested for once. 2.
The other Trigger Modes 1.Non-Remote Control Mode: Set the compatible flash on the transceiver to Manual or RPT flash mode, the flash will work according to the mode and parameters displayed, the controller will not support the remote controlling the flash mode or flash exposure compensation (flash output). 2.PC interface & Basic flash Trigger(Support non Nikon body) PC interface (input) trigger: Use LS-PC/PC cable (option)to connect the controller and the PC interface of camera.
Shutter Release Function Use the YN-622N transceiver for wireless transmitting, the YN-622N-TX controller as the shutter signal output. 1).Install the YN-622N-TX controller on the camera’s hot shoe, and use LS-2.5 series shutter connecting cable(may additional purchases) to connect the controller and camera. 2).Long press the [TEST] button of YN-622N transceiver to focus, loosen the [TEST] button to shot.
Reference 1.Flash Shutter Sync: Refer to the camera’s setting. Supports front-curtain sync, rear-curtain sync and high speed synchronous(Auto FP*).The relevant icons will be displayed on the LCD(P.4). Using high-speed synchronization need to set the flash sync speed of the camera to “AUTO FP”. The maximum sync speed is 1/8000s or 1/4000s (depends on the camera).
Reference 5.Factory Reset Hold down the [MODE] and [AF/SS] buttons at the same time until the screen as shown, then loosen to restore factory settings. 6.USB Firmware Upgrade 1).Visit YONGNUO official website: http://www.hkyongnuo.com/e-detail.php?ID=339 to download the firmware upgrade software and the latest firmware. 2).Turn off . Keep pressing [mode] button and turn on again. The screen will show firmware upgrade interface( will display the current version ). 3).
Troubleshooting 1. Fail to power on or automatic shutdown: The battery is loaded inversely or exhausted. Ø Install the battery according to the correct direction the battery compartment indicates and ensure the battery is full and restart the power . 2.
Specifications System type: Digital FSK 2.4GHz wireless controller Distance: 100M Channel: 7 Flash mode: i-TTL, Manual flash, Super Sync Sync mode: front-curtain sync, rear-curtain sync, Hi-speed sync(Auto FP) Groups: 3Groups (A/B/C) MAX Sync speed: 1/8000s Trigger Interface: Hot-shoe,PC Shutter release interface: 2.5MM shutter release interface USB Firmware Upgrade: support AF Assist Beam Emitter: support Battery: AAX2(support 1.2 V rechargeable battery)3V Stand-by time: 120h Dimensions: 89.
FCC ID: 2ACYPYN622N-TX SHENZHEN YONGNUO PHOTOGRAPHIC EQUIPMENT CO., LTD Model name: i-TTL Wireless Flash Controller Model No.: YN622N-TX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.