FEB/FEC(E-TTL only) 1. FEB (Flash Exposure Bracketing) Support 1/3-stop increments to set FEB within ±3. ※ The sequence of FEB is fixed at 0→ -→ +, even the FEB sequence of the custom setting in flash is different, the shoot sequence remains to 0→-→+ either. ※ FEB function will be automatically cancelled after three shots are taken. ※ Even the E-TTL flash does not support FEB can also realize this function. 2. FEC (Flash Exposure Compensation) Support 1/3-stop increments to set FEC within ±3.
Zoom (Flash Coverage) Zoom supports automatic/manual setting. 1. With automatic setting, focal length of the flash may change with lens focal length. 2. With manual setting, focal length of the flash supports manual setting within 24-105MM. 1. Automatic Setting 2. Manual Setting 3. Zoom Lock Hold down the [CH SET] button of the receiver for seconds until channel indicator keeps lighting (same to set the mix control mode for the transmitter, p.
Manual Flash / Multi Flash 1.Manual Flash: Manually set flash output (1/128~1/1 power 1/3-stop increments) Select flash mode as Manual Flash Mode, setting flash output ,shutter sync, zoom etc. 2.Multi Flash (Stroboscopic flash) Select flash mode as Multi Flash, setting via the camera menu.
Wireless Function* By setting the wireless flash function menu, in a different flash mode or firing group, remotely set A / B / C, three groups of flash ratio or flash output. 1. Enabled the wireless function via flash control menu. 2. Master Flash: Option for a flash which installed on the t r a n s m i t te r ( o n - to p f l a s h ) , s e l e c t e n a b l e f o r f i r i n g o r disable. On-top flash exposure setting as well as group A.
Wireless Function 3.Channel Setting via Wireless Function Set channel (CH1-CH4 only) of the transmitter via wireless function setting, the changed shall cover the original setting. CH1-CH7 may also be set by directly pressing [CH SET] at the transmitter(p.8). 4.
Flash Ratio with E-TTL II Flash fire ratio and FEC of the A, B, C three firing groups can be set under E-TTL II flash mode. 1.All (A+B+C) R a t i o o f f, A / B / C t h r e e flashes automatically fire with same output, flash exposure compensation (FEC)can be set. 2.A:B Set fire ratio (8:1-1:8, 1/2stop increments) and flash exposure compensation for flashes of Group A and B, Group C does not fire. 3.
Manual/Multi Flash Output Flash output for each group A/B/C can be separately set under Manual/Multi flash mode. 1. All (A+B+C)-The three groups of flashes shall be set with the same output. 2. A: B-Group A and B shall be separately set , Group C flash will not fire. 3. A: B: C-Group A, B, C shall be separately set. ※Flash output under menu root is same to Group A.
Mix Control Mode Set the flash on each receiver in different flash modes as Manual/E-TTL/Multi for mix control, the settings of the flash is prior , channel indicator of the transmitter will keep lighting when enabled this control mode. Supports type A/B cameras using. 1. Hold down the [CH SET] button for several seconds of the transmitter until the channel indicator blinks for 3 times and then keep lighting, enable the mix control mode. 2.
Flash Triggering of B/C Type Camera Type B Cameras: There is no flash control menu of such type of cameras that some of function will be restricted. Enable the mix control mode of the transmitter before using(P.21). 1. Setting of transmitting groups (set in the transmitter when it in transmitting status): Half press the camera’s shutter button then status indicator blinks green. Press [GP SET] to set transmitting firing groups.
PC Port Triggering (Support Super Sync *) Caution! Do not connect to the PC port any flash requiring trigger voltage more than 300V, or the transceiver may be damaged. Purchase corresponding PC flash sync cord according to the different ports of the flashes needs . 1. Use an end of PC sync cord with nut to connect to the receiver. 2. The other end of the PC sync cord connects to strobe flashes or other flashes which supporting PC port. 3. Set the camera's shutter sync as 1st curtain or 2nd curtain. 4.
References AF Assist Beam Emitter When using AF under low-light, the built-in AF-assist beam emitter of the transmitter will be emitted automatically to make it easier to autofocus, and the flash on the transmitter which support AF assist beam emitter function can also be emitted at the same time. ※ It needs using single autofocus for the lens. ※ It needs enabled the AF assist beam function of camera (flash) by custom functions setting. Can also disable this function by custom functions setting(C.Fn8).
Reference-About 560-RX The YN622C II supports receiving the triggering signal YN560-TX (RF603 communication mode),when using the compatible flash, it can wireless control the flash mode, flash output and zoom of each group; meanwhile supports the triggering signal(the flash set to M mode) of the RF603(II)、 RF605(RF603 communication mode). Supports grouping function of the YN560-TX、RF605. 1.Set to the 560-RX mode through the power switch. 2.
References Firmware Update 1.Log in the YONGNUO official website: http://www.hkyongnuo.com/e-detaily.php?ID=364 to download the firmware update software and the latest firmware. 2.Power off, use Micro-USB(do not include) cable connect to PC. 3.Press the button and set the power on, all the indicator bright(green). 4.Complete the firmware upgrade operation according to the prompt of software.
Troubleshooting 1. Fail to power on or automatic shutdown: batter y is loaded inversely or exhausted; the status indicator light will blink(red) separately when the batter y is going to be exhausted, and it will power off automatically in case of being over discharged. ▲ Install the batter y according to the correct direction, ensure the batter y is full and restart the power (refer to page 8). 2.
Troubleshooting 6. The assist beam emitter doesn't work : Refer to page 24. 7. The on-top flash doesn't fire: Enabled the master flash via the wireless function setting. 8. Can't set the flash zoom via camera menu: W h e n t h e m i x control mode has been set in the transmitter (p.21) or zoom locking has been set in the receiver (p.15), zoom can't be set via camera menu. Zoom setting of the on-top flash needs to be set separately(p.17). 9.
Specifications System type: Digital FSK 2.4GHz wireless transceiver Distance: 100M Channel: 14 Flash mode: E-TTL(II), Manual flash, Multi flash Sync mode: 1st curtain, 2nd curtain, Hi-speed sync Groups: A/B/C 3Groups(622);A/B/C/D/E/F 6Groups (560-RX) Max Sync speed: 1/8000s* Input: Hot-shoe(TTL,main contact) Output: Hot-shoe, PC port Firmware upgrade terminal: Micro USB Applicable batter y: AAX2 (support 1.2 V rechargeable batter y) Stand-by time: 60h Dimensions: 91.5X53.
FCC ID: 2ACYPYN622CII This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.