User Manual 用户手册
CONTENTS 注意事项 Cautions . . . . . . . . . . . . General Description . . . . . . . Supported Functions List . . . . . Compatibility List . . . . . . . . Name of Parts . . . . . . . . . Preparation Before Use . . . . . . Setting. . . . . . . . . . . . . Flash Awaking /Testing Flash . . . . Remote Control Mode. . . . . . . Automatic Flash (E-TTL II) . . . . Shutter Sync . . . . . . . . . . FEB/FEC . . . . . . . . . . . Zoom (Flash Coverage) . . . . . Manual/Multi Flash . . . . . . . Wireless Function . . . . .
Cautions Please turn off power supplies of all equipment when connecting or installing the product. Please keep it dr y. Be sure not to use wet hand to touch the product. It is also not allowed to immerse the product into waster or make it be exposed in the rain; other wise it may not work normally or even be damaged. Do not use it in explosive situations; violation of this warning may cause an explosion or fire.
General Description Thank you for purchase the products of Yongnuo firstly. Y N - 6 2 2 C E - T T L w i re l e s s f l a s h t r i g g e r i s a h i g h performance master and slave equipment of multiple flashes photography, through digital FSK 2.4GHz radio wireless transmission, and different photographic effects can be realized through setting your flash at 360 degrees. It design of transceiver, the distance of remote control reaches 100M, supporting 7 wireless channels and A/B/C three groups.
Supported Functions List Compatible flash mode: E-TTL (II)/ Manual/ Multi Compatible Shutter sync: 1st curtain, 2nd curtain, high speed sync (HSS/FP), Max 1/8000s sync speed Control remote flash using camera's flash control menu screen(Remote Control Mode) Support E-TTL / Manual/ Multi flash mode mix using(Mix Control Mode) Flash on hot-shoe of transmitter supports ETTL Support Flash Exposure Compensation (FEC) Support Flash Exposure Bracketing (FEB) Support Flash Exposure Lock (FEL) Suppo
Compatibility List Functions supported by the product depend on the camera and flash used. According to different types of cameras, in this user manual, the EOS DSLR camera with external flash(speedlite) control menu is called type A camera ; while EOS DSLR camera without external flash control menu is called type B camera ; other camera brands with standard hot-shoe is called type C camera .
Name of Parts Indicator Channel Indicator Blinking Keep Lighting Communicating Mix Control Mode (Remote control mode) Firing group or Testing receiving group Communicating State Indicator(green) TX Communicating Testing Communicating State Indicator(red) RX Communicating Standby State Group Indicator ※The protective film can be torn out. 1).Standby state(red) 2).TX communicating state(green blinks) 3).RX communicating state(red blinks) A Channel indicator (p.8) I PC port(p.
Preparation Before Use 1. Installing the Batteries Open the cover and install two AA batteries (excluded)according to the + and - marks , rechargeable batteries of 1.2V can be used. Replace the batteries when the product does not work stably. ※ Remove the batteries when the product is not used for long time. ※ Please replace the both two batteries at the same time. 2.Installing the Transceiver on the Camera (As Transmitter) 1). Unscrew the locking ring of the transceiver. 2).
Preparation Before Use 3 . I n s t a l l F l a s h o n t h e H o t S h o e of t h e Transceiver (as Receiver) 1. Install the transceiver on the mini stand or other fixing equipment (excluded). 2. Loosen the locking ring of the flash. 3. Slip the mounting foot of the flash into the receiver. 4. Tightly lock the locking device of the flash. Caution! The hot shot of the transceivers can only install flash being applicable to DSLR cameras, can not install highvoltage flash, or the transceiver may be damaged.
Setting 1. Power Switch Power on when the power switch slides to [ON], channel and group indicators shows that channel and receiving group, power off when the power switch slides to [OFF]. ※ It is normal for the flash fire once when turning on/off the transceiver. 2.
Setting 4.Flash Test Group Setting (Test + GP SET Button) Set flash testing group Type C camera uses the set firing group. 1. H o l d d o w n [ Te s t ] b u t t o n t h e n t h e g r o u p indicators will keep lighting, the flash on the receiver group having been selected will be woken up(p.10). 2. Hold down [Test] button and repeat to shortly press [GP SET] button, selected groups of receivers to testing flash, and there are totally 7 combinations. 3.
Flash Awaking and Testing Flash When half-pressing the shutter button of the camera, the hot-shoe flash on the receiver will be awakened. (for A/B type camera only) Under any connection type, [Test] button can be pressed to awaken and test the flash on the transceiver and other transceivers at the same channel. Test flash with the mode set by the flash, and under the mode of E-TTL it may fire in a lower output.
Remote Control Mode Remotely setting all the flashes through the external flash function setting (camera menu) of the camera, just likes the flash being directly installed on the camera. The settings of camera menu is prior, settings will upgraded to the receiver after pressing down camera confirmation button or half pressing shutter button without needing to operate the flash control panel, the flash’s screen will display the current setting. The setting varies depending on the cameras/flashes.
Automatic Flash (E-TTL II) Fully-automatic Flash Shooting 1. Select flash mode as E-TTL II mode. 2. Half press camera's shutter button to focus, and on the flash screen the aperture and effective range etc. parameters will be displayed. 3. Ensure that the subject is in the effective flash range, full press camera’s shutter button to shoot, the flash will be fire according to the setting. ※ Exposure lever increments may set to 1/3-stop via the camera.
Shutter Sync 1. 1st Curtain sync The normal flash sync. 2. 2nd curtain sync The flash fires right before the shutter closes, lower shutter speed needs to be used, support bulb 2nd curtain sync flash. ※Only when wireless flash function via the flash control menu is disable , the 2nd curtain sync can be use. 3. Hi-speed Sync(HSS/FP FLASH) The flash can sync with all shutter speeds when using HSS . The max speed is 1/8000s or 1/4000s(depends on the camera).
FEB/FEC(E-TTL only) 1. FEB (Flash Exposure Bracketing) Support 1/3-stop increments to set FEB within ±3. ※ The sequence of FEB is fixed at 0→ -→ +, even the FEB sequence of the custom setting in flash is different, the shoot sequence remains to 0→-→+ either. ※ FEB function will be automatically cancelled after three shots are taken. ※ Even the E-TTL flash does not support FEB can also realize this function. 2. FEC (Flash Exposure Compensation) Support 1/3-stop increments to set FEC within ±3.
Zoom (Flash Coverage) Zoom supports automatic/manual setting. 1. With automatic setting, focal length of the flash may change with lens focal length. 2. With manual setting, focal length of the flash supports manual setting within 24-105MM. 1. Automatic Setting 2. Manual Setting 3. Zoom Lock Hold down the [CH SET] button of the receiver for seconds until channel indicator keeps lighting (same to set the mix control mode for the transmitter, p.
Manual Flash / Multi Flash 1.Manual Flash: Manually set flash output (1/128~1/1 power 1/3-stop increments) Select flash mode as Manual Flash Mode, setting flash output ,shutter sync, zoom etc. 2.Multi Flash (Stroboscopic flash) Select flash mode as Multi Flash, setting via the camera menu.
Wireless Function* By setting the wireless flash function menu, in a different flash mode or firing group, remotely set A / B / C, three groups of flash ratio or flash output. 1. Enabled the wireless function via flash control menu. 2. Master Flash: Option for a flash which installed on the t r a n s m i t te r ( o n - to p f l a s h ) , s e l e c t e n a b l e f o r f i r i n g o r disable. On-top flash exposure setting as well as group A.
Wireless Function 3.Channel Setting via Wireless Function Set channel (CH1-CH4 only) of the transmitter via wireless function setting, the changed shall cover the original setting. CH1-CH7 may also be set by directly pressing [CH SET] at the transmitter(p.8). 4.
Flash Ratio with E-TTL II Flash fire ratio and FEC of the A, B, C three firing groups can be set under E-TTL II flash mode. 1.All (A+B+C) R a t i o o f f, A / B / C t h r e e flashes automatically fire with same output, flash exposure compensation (FEC)can be set. 2.A:B Set fire ratio (8:1-1:8, 1/2stop increments) and flash exposure compensation for flashes of Group A and B, Group C does not fire. 3.
Manual/Multi Flash Output Flash output for each group A/B/C can be separately set under Manual/Multi flash mode. 1. All (A+B+C)-The three groups of flashes shall be set with the same output. 2. A: B-Group A and B shall be separately set , Group C flash will not fire. 3. A: B: C-Group A, B, C shall be separately set. ※Flash output under menu root is same to Group A.
Mix Control Mode Set the flash on each receiver in different flash modes as Manual/E-TTL/Multi for mix control, the settings of the flash is prior , channel indicator of the transmitter will keep lighting when enabled this control mode. Supports type A/B cameras using. 1. Hold down the [CH SET] button for several seconds of the transmitter until the channel indicator blinks for 3 times and then keep lighting, enable the mix control mode. 2.
Flash Triggering of B/C Type Camera Type B Cameras: There is no flash control menu of such type of cameras that some of function will be restricted. Enable the mix control mode of the transmitter before using(P.21). 1. Setting of transmitting groups (set in the transmitter when it in transmitting status): Half press the camera’s shutter button then status indicator blinks green. Press [GP SET] to set transmitting firing groups.
PC Port Triggering (Support Super Sync *) Caution! Do not connect to the PC port any flash requiring trigger voltage more than 300V, or the transceiver may be damaged. Purchase corresponding PC flash sync cord according to the different ports of the flashes needs . 1. Use an end of PC sync cord with nut to connect to the receiver. 2. The other end of the PC sync cord connects to strobe flashes or other flashes which supporting PC port. 3. Set the camera's shutter sync as 1st curtain or 2nd curtain. 4.
References AF Assist Beam Emitter When using AF under low-light, the built-in AF-assist beam emitter of the transmitter will be emitted automatically to make it easier to autofocus, and the flash on the transmitter which support AF assist beam emitter function can also be emitted at the same time. ※ It needs using single autofocus for the lens. ※ It needs enabled the AF assist beam function of camera (flash) by custom functions setting. Can also disable this function by custom functions setting(C.Fn8).
References Applications 2 Transceiver Kit Packaged one off-camera flash or one off-camera flash plus one ontop flash can be used. Multiple Transceivers Multiple flashes application by additionally purchased transceivers. Factor y Reset 1) Hold down the buttons [CH SET] plus [GP SET] at the same time. 2) The state indicators will blink for 3 times in red-green alternately then turn to keep lighting (red). 3) Release all the buttons then reset the factor y set.
Troubleshooting 1. Fail to power on or automatic shutdown: ● The batter y is loaded inversely or exhausted; it will power off automatically when the batter y is going to be exhausted in case of being over discharged. ▲ Install the batter y according to the correct direction the batter y compartment indicates and ensure the batter y is full and restart the power (refer to page 8). 2.
Troubleshooting 7. Can't set the flash zoom via camera menu: When the mix control mode has been set in the transmitter (p.21) or zoom locking has been set in the receiver (p.15), zoom can't be set via camera menu. Zoom setting of the ontop flash needs to be set separately(p.17). 8. Fail to set channel 5, 6, 7 via camera menu: This is caused by the camera restriction and it can only set the channel 1-4 in via camera menu, while other channels can be set via channel button. 9.
Specifications System type: Digital FSK 2.4GHz wireless transceiver Distance: 100M Channel: 7 Flash mode: E-TTL(II), Manual flash, Multi flash Sync mode: 1st curtain, 2nd curtain, Hi-speed sync Groups: 3Groups (A/B/C) Sync speed: 1/8000s* Input: Hot-shoe(TTL,main contact) Output: Hoe shoe, PC port Applicable batter y: AAX2 (support 1.2 V rechargeable batter y) Stand-by time: 60h Dimensions: 89.5×53×39mm Weight:78g * Sync speed of part of cameras and flashes may be lower.
FCC ID: 2ACYPYN622C This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.