YN622C-TX Wireless Flash Controller ZOOM CH User Manual 用户手册
Contents/Cautions General Description . . . . . . . . . . . . . . . . . 1 Conventions Used in the Manual . . . . . . . . . . 2 Supported Functions List . . . . . . . . . . . . . . . 3 Name of Parts/Quick Start Guide . . . . . . . . . . . 4-5 Preparation Before Use. . . . . . . . . . . . . . 6 Settings. . . . . . . . . . . . . . . . . . . . . 7-11 Flash Awaking and Triggering . . . . . . . . . . . 12 Control from Camera’s Menu Screen . . . . . . . . . 13 C.FN: Custom Function Settings . . . . . . . . . .
General Description Thank you for choosing products of YONGNUO. YN622C-TX E-TTL wireless flash controller is for supporting the use of YN622C E-TTL wireless flash trigger transceiver. This product adopts flexible LCD menu control, supports mixed use of E-TTL(II) mode, manual mode, or super sync flash mode of group A/B/C flash. Supports multi flash, supports E-TTL ratio. It can be adjusted the exposure compensation or flash output of each group.
Conventions Used in the Manual This manual to assume using compatible camera/flash and YN622C transceiver in the same channel. The features/functions supported by the product depend on the camera and flash used. For the operation of camera, flash ant the YN622C transceiver, please refer to relevant user manuals. For the user manual and firmware of the latest version, please visit the official website of YONGNUO: www.hkyongnuo.com.
Supported Functions List LCD screen display, and multi-buttons for quick operation The firmware can be upgraded through the USB interface Supports wireless shutter release function The focal length(zoom)of the A/B/C three group flash can be adjusted separately Supports TTL Ratio A:B / A:B C AF-assist beam emitter function (can be disabled) Flash mode: GR(grouping flash)/E-TTL(II)/Multi flash Supports mixed use of E-TTL(II) mode, manual flash mode or super sync(SS) of A/B/C group flash.
Name of Parts/Quick Start Guide ※The protective film can be torn out.
Name of Parts/Quick Start Guide A-LCD: Display all the settings of controller. B-2.5MM Shutter release interface: Wireless shutter release function(P.16). C-AF assist beam emitter: (P.14) D-PC interface: Input the flash sync signal(P.15). E-USB interface: Connected to the computer to update the firmware (P.19). Fbutton: Flash mode setting. G-GR/* button: Short press to move the arrow to set flash group or other parameters; Long press to get different functions int different modes.
Preparation Before Use 1.YN622C Transceiver Settings: Set the receiving group and channel of the transceiver (refer to the user manual of the YN622C). 2.YN622C-TX Controller Settings: 1).Installing the 2 AA (1.5V)batteries (excluded). 2).Installing the Controller on the Camera . 3).Power on when the power switch slides to [ON]. 4).Channel Setting: Long press the [ZOOM/CH] button, then press the select/set button group to the same channel as the YN622C transceiver.
Settings Flash Mode Setting: GR/TTL/Multi Long press the [ mode GR/TTL/Multi. ] button to switch the flash In GR mode, short press the [ ] button to switch the current group the arrow pointing to; in TTL/Multi mode, short press this button can also switch the flash mode. Examples: 1.GR 2.TTL ZOOM CH 3.
Settings 1.GR-Grouping flash mode: set different flash modes for different groups. 1).short press the [GR/*] button to choose the setting groups. 2).Short press the [ ] button to set the flash mode of the selected group, each press of the setting as below: ZOOM CH TTL: E-TTL(II) Fully Automatic Flash The FEC adjustment range is within -3 to +3EV, It’s supported to press select/set button group to adjust the FEC value.
Settings 2.E-TTL(II)Mode -Fully Automatic Flash 1.)Set the flash group: Long press the [GR/*] button to set the TTL flash group. 2.)Set the flash ratio or exposure compensation: Short press the [GR/*] button to select the setting items, then press the select/set button groups to set the parameters. 1. Flash Group- A+B+C(ALL) Set FEC of A/B/C groups at one time. 2. Flash Group- A:B Set flash ratio of A/B group Set FEC of the A/B group(C group does not flash ) 3.
Settings The details of the flash ratio settings as below: Press[LEFT]or[RIGHT] Press[UP]or[DOWN] 3.Multi Flash Mode:Stroboscopic Flash Short press the [GR/*] button to select the items, then press the select/set button groups to set the parameters. Output power Stroboscopic frequency Stroboscopic flash count *The output power of group B/C should be set up respectively through the camera’s menu (P.
Settings 4.ZOOM:Flash Coverage Setting It supports the controller to set the focal length of the flash on the transceiver. Short press the [ZOOM/CH]button, ZOOM CH set the flash focal length of A/B/C group in sequence, then press the Select/Set button group and set. Settings rang supported manual 24-105mm,AU (Automatic). 5.Flash shutter sync ZOOM CH Short press the [SYNC/FN] button to set the shutter sync mode(except the multi flash).There will be a relevant icon displayed on the LCD.
Flash Awaking and Triggering 1.Flash Awaking&Testing When half press the shutter button of the camera or press the [TEST] button of the controller , the green wake-up indicator light lights on, and the flash on the hot-shoe of the transceiver will be waked up. When loosen the [TEST] button, the flash of the selected groups will be tested for once. 2.Flash triggering Completely press the shutter button of the camera will trigger the flash synchronously, the red triggering indicator light lights on.
Control from Camera ' s Menu Screen When using EOS digital cameras released since 2007, you can set the controller functions from the camera’s menu screen. For the operation of the camera, please refer to the relevant user manual. EOS digital cameras released since 2012:support E TTL II, manual flash, multi flash, group flash (GR). EOS digital cameras released from 2007 to 2011:supports E-TTL II, manual flash, multi flash Under the TTL mode, it supports the camera menu setting FEB function.
Custom Function Settings(C.FN) 1).Long press the [SYNC/FN] button. 2).Press the [up] or [down] buttons to select the setting items, then press the [LEFT] or [RIGHT] buttons to set the parameters. 3).Press [OK] to confirm and exit the settings. 01-SS: Super sync delay Settings The range of settings : 0.0-2.0 (refer to P.17) ZOOM CH 02-SHU(Shutter):Wireless shutter function Refer to P.
Other Trigger Modes 2.PC interface & Legacy Flash Trigger PC interface (input) trigger: Use LS-PC/PC cable (option)to connect the controller and the PC interface of camera. (Single Contact) trigger: Install the controller on the camera hot shoe. Legacy Flash Trigger : Basic flash 1).Transmitting group setup: Set base on the groups of the controller (GR). 2).
Shutter Release Function Use the YN622C transceiver for wireless transmitting, the YN622C-TX controller as the shutter signal output. YN622C-TX C1 C3 YN622C 1).Use the LS-2.5 series shutter connecting cable to connect the controller and camera’s shutter interface, as for the EOS digital cameras released after 2012, it does not need the shutter connecting cable. 2).Set the C.FN 02 as ON (P.14),turn on the wireless shutter function. 3).
Reference 1. About the Super Sync(SS) Use non-HSS (Non High Speed Sync) flash to realize High Speed Sync. This function is more applicable to strobes flashes whose flash duration is longer. It should be used with cameras which supports High Speed Sync (HSS) and setting SS time delay parameters. A-Set the controller SS time delay parameters in C.FN 01: (refer to Page 14) B-Using Super Sync: 1).Set the flash into manual mode.
Reference 3.About the Ex Compat trigger When using the 430ex/550ex/580ex flash etc. which does not support camera menu controlling the flash, enable this function can use the controller to remote control the manual flash power output of the above flash. 1).Set the C.FN 05 of the controller as ON(P.14). 2).Set the flash on the YN622C as E-TTL flash mode. 3).Set the controller as manual flash under the GR mode, set the flash output. *The flash screen will not display the flash output.
Reference 5.Factory Reset ZOOM CH Hold down the [MODE] and [SYNC/FN] buttons at the same time until the screen as shown, then loosen to restore factory settings. 6.USB Firmware Upgrade ZOOM CH 1).Visit YONGNUO official website: http://www.hkyongnuo.com to download the firmware upgrade software and the latest firmware. 2).Turn off . Keep pressing [mode] button and turn on again. The screen will show firmware upgrade interface(will display the current version ). 3).
Troubleshooting 1. Fail to power on or automatic shutdown: The battery is loaded inversely or exhausted. Ø Install the battery according to the correct direction the battery compartment indicates and ensure the battery is full and restart the power . 2. The flash doesn't fire Ø Ensure the power of all equipments are full, the flash is in ready state(the flash-ready indicator on) Ø Ensure the connection among the controller( transceiver), camera and the flash is reliable.
Specifications System type: Digital FSK 2.4GHz wireless controller Distance: 100M Channel: 7 Flash mode: GR(E-TTL(II), Manual, Super Sync)/E-TTL(II)/Multi flash Sync mode: 1st-curtain, 2nd-curtain, Hi-speed sync(HSS) Groups: 3Groups (A/B/C) MAX Sync speed: 1/8000s Trigger Interface: Hot-shoe,PC port Shutter release interface: 2.5MM shutter release interface TTL Ratio: support USB Firmware Upgrade: support AF Assist Beam Emitter: support Zoom: support Battery: AAX2(support 1.
FCC ID: 2ACYPYN622C-TX SHENZHEN YONGNUO PHOTOGRAPHIC EQUIPMENT CO., LTD Model name: E-TTL Wireless Flash Controller Model No.: YN622C-TX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.