Contents Introduction . . . LL... 1 Nomenclature. ava a aes 24 Preparation Beforehand. 56 Wireless Flash Hooking. 7 Wireless Settings 8-9 Fretfully Automatic Wireless Flash Shooting, 10-14 M: Wireless Multiple Flash Shooting with Manual Flash Output. 15-16 MULL Stroboscopic Flash 17 Gr: Shooting with a Different Flash Mode for Each Group. 18-19 Remote Release from a Slave Unit/Linked Shorting . . . 20-21 Transmitter Control from Camera's Menu Screen 22-23 C. Fn: Transmitter Custom Function Settings.
Introduction The XIONGNU Speed lite Transmitter YN-E3-RT Is a transmitter for wireless flash shooting. It can control up to 5 groups (15 units) of Speediness that have a wireless multiple flash shooting function using radio transmission. The transmitter also has dust and water resistance equivalent to EOS-1D series cameras.
Nomenclature The protective film can be tom out. Function button 2 Function button 1. Linked shooting button Flash mode button. Charge Test flash button’ Function button Analects button+} Function buttons. Mounting foot, lock lever : Rawer on LOCK : Button/dial lock Lock release ack, But fry OFF: Power off Dust.
Nomenclature E-TEL (II) Auto flash FEB FEB sequence . stet JT TU —— High-speed sync Rationalistic ratio. Personal Functions OLIVETTI : Beep authorship [Er . Radio transmission Flash exposure {| 28:1 B11 4 compensation) Channel AUT anal Siting group To: ¢ Flash ratio automatic sa | Custom Flash exposure level Functions lave flash ready . Manual Flash 2nd 7] Ty] curtain syn Manual flash output « Tha display will show only the settings currently applied.
Nomenclature Multi{stroboscopic) flash Group firing Flash mode. Firing group. mT BLT Ee Linked shooting LINKED SHOT: Linked shafting LINKED SHOT wi 40) i ALE M Ult: Ult flash Lumbar of flashes.
ion Before Use Preps 1.Install two AA/LR6 batter 1.0pen the cover:Slide the cover down as shown and open the battery compartment two AA batteries: Install two AA batteries according to the + and marks, nonchargeable batteries of 1.2V can be used. 3.Close the battery: Close the battery Compartment cover and slide it up. * Remove the batteries when the product Is not used for long time. Please replace the both two batteries ot the same time. * When <1» Is Inced, replace the 2.
Preparation Before Use 3.Turning on the Powerless the prows switch to . » The LCD panel illuminates. The charge lamp lights when the wireless shooting (slave) Is ready. «During wireless shooting, press the transmitter’s charge lamp (test flash button) to fire a test flash. About Auto Power Off To save battery power, the power will turn off automatic after 5 min. of Idle use. To turn on the transmitter again, press the camera's shutter button halfway, or press the test flash button (charge lamp).
Wireless Flash Shooting Using a transmitter and a Speedily compatible with radio transmission wireless shooting makes It easy to shoot with advanced wireless multiple flash lighting, In the same way as normal E-TEL auto flash shooting. The system Is designed so that the settings of the transmitter attached to the camera (master) are automatically reflected on the Spitted that Is tirelessly controlled (slave).
recce, Sat tha same channel and ID for both the master unit and slave unit, Set a flash that Is compatible with radio transmission wireless flash shooting as the slave unit. For the slave h's |i Wireless Radio ID. 1. Dlsplay
. » Press function button 4 to display | . 2.Set a Chan » Press function button 1 . = Turn select "AUTO" or a channel from and press the <@ > button, 3.5et a wireless radio ID.Wireless Settings * Scanning the Master Unit Transmission Channels to Set You can scan the radio reception status and set the master unit's transmission channel automatically or manually. When the channel Is set to "AUTO", the channel with the best reception signal Is automatically set. When setting the channel manually, You can set the transmission channel again while referring to the scan results. Scanning while "AUTO" Is set Run the scan. Fretfully Automatic Wireless Flash Shooting 1.Set the flash as the slave unit Tha flash will not fire If Rotisserie. 2.Set the same channel and ID of the master unit and slave unit «p-8) 3.Position the camera and the 4. Prass tha button on the master unit and set the flash mode to KETTLE. * The slave unit Is sat automatically to KETTLE during shooting via the control from the master unit. 5. Chack the transmission status ‘and that the flash Is ready. * Check that the lamp is lit in green. Fretfully Automatic Wireless Flash Shooting Support increments ta set FEEBLE within £3. FEC (Flash Exposure Compensation) 1.Press function button 4 to display < III >.Press function button 2 < KZA >. < ETA> ls displayed and the FEC amount Is highlighted. 2.Turn <> to set the flash exposure compensation amount, and press <@ >. The FEC amount is sat. * To cancel FEC, return the amount to £0", FEB (Flash Exposure Bracketing) Press function button 4 fo display < ILEA >. Press function button 3 . Fretfully Automatic Wireless Flash Shooting High-speed Sync With the high-speed sync function, the flash can synchronize nt when you want subject. splay , Press function button 4 to display . 2. Dlsplay < * Press function button display Check that <$H> is lit in the viewfinder. FEL : FE Lock FE (Flash Exposure) lock locks the correct flash exposure setting for any part of the scene, Perform FE lock by operating the camera, For th operations, see the camera and flash’s Instruction manual. ETTA: Wireless Multiple Flash Shooting with Flash Ratio The exposure is controlled automatically so that the total flash output of firing groups results In the standard exposure. 1.Set the firing group of the slave units. * Operate and set tha slave units one by one. 2. Prass tha master unit's function button 4 to display ACETATE. 3.Press function button and set to or ABC>. 4.Set tha flash ratlo. Prass function button Press function button 3 <[EX3 > or . ETTA: Wireless Multiple Flash Shooting with Flash Ratio Slavs Group Control If you need more flash output or wish Firing group A | ta perform moral sophisticated lighting, you can Increase the number of slave units. Simply set an additional slave unit to the firing group whose flash output you want to Increase. You can Increase the number of slave units up to 15 units In total. M: Wireless Multiple Hash Shooting with Manual Hash Output This describes wireless (multiple flash) shooting using manual flash. You can shoot with a different flash output setting for each slave unit{firing group). Set all parameters on the master unit. 1. Setthe flash mode to . 2.5et the number of firing groups. |