RF605C Wireless Flash Trigger User Manual
Contents Thank you for purchasing YONGNUO products in advance. On-Top Please be sure to read and understand this user Flash manual and the usage of camera and flash before using. This product is a wireless transceiver Transmitter integrated design, for the convenience of description, the product will named “transmitter ” when mounted on the camera hot shoe,named “receiver ”when mounted or connected to the flash. Off-Camera Flash Receiver Product Features . . . . . . . . . . . . . . . . . . . . . . . . .
Product Features RF-602/RF-603 two communication modes RF605 = RF602 +RF603 TX/RX/TRX multiple working ways A/B/C/D/E/F 6 groups (compatible with YN560-TX) Wireless shutter remote control Clear LCD screen display, shortcut key operation 16 channels Communication range up to 100M Package Contents: RF605C or RF605N . . . . . . . . . . . . . . . . . . . . . . X2 LS-2.5 shutter connecting cable* . . . . . . X2 User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions 1. As this is an electronic product accessor y, some of the environment causes may affect the working. However this is hardly ever to get this situation, don't worr y. 2. Do not pull the wires and turn off the camera when connecting. 3. For a long time non-use, please turn the transceiver off and remove the batteries. 4. Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high temperature areas. 5.
Names of RF605 Parts RF605C is more suitable for the Canon cameras 3 RF605N is more suitable for the Nikon cameras A-Hot shoe stand/Hot shoe contacts: install flash B-2.5mm shutter release socket C-Focus light (Green)/shutter indicator light (Red),in RF-603 TRX status, the AF-assist light will blink once in ever y 2 seconds. D-PC interface(output) E-Waken indicator (Green)/trigger indicator light (Red),in RF-602 RX status , the trigger indicator light will blink once in ever y 2 seconds.
Button,display,indicator light Button Communication mode/Transmitreceive status button Channel Transmit grouping button Transmit-receive grouping button 【Multifunction Button】 Function Display/Indicator light Long press to switch the communication mode RF-602/RF-603;Short press to switch the transmit-receive status RF-602 can use TX(transmit),RX(receive) St a t u s ; R F - 6 0 3 c a n u s e T X ( t r a n s m i t ) , TRX(transmit-receive) status Press to setup the channel (1-16) Press the button to act
Preparation before using 1.Batter y Installation: Slide to open the batter y compartment, install two AAA batteries(not included) for two transceivers according to the "+/-"direction shown. The low batter y Indicator( ) The low batter y indicator will blink when the batteries are low. Please replace the batter y. 2.Fix the transmitter on the hot shoe of the camera: Mount the transmitter on the hot shoe of the camera through the hot shoe mounting foot, then tight the locking screw.
Wireless triggering and testing 1.Set the communication mode: Set all the transmitters and receivers to the same communication mode (RF-602 or RF-603). 2.Set the transmit-receive status: Set the transmitter to TX, the receiver set to RX or TRX. 3.Channel setting: Set all the transceivers in the same channel. 4.
Wireless triggering and testing Example: use the YN560-TX and set C group not flash Set the C group flash mode to “--” when using the YN560-TX ,the C group of corresponding RF605 receiver does not flash. YN560-TX RF605 5.Waken the flash: half press the transmitter(TX status) multifunction button or camera shutter to waken the flash. 6.Test and trigger the flash :Fully press the multifunction button of the transmitter (TX status) to test the flash once.