Smart Security Panel Kit User Manual
CONTENT I. II. III. General Description................................................................................................................................. 1 1.1 Product Example ...................................................................................................................... 1 1.2 Home Installation Diagram........................................................................................................ 2 Set up the Security Devices .............................
I. General Description 1.1 Product Example Security Panel The central hub of the security system. Using 4.3-inch IPS capacitive touch screen, built-in highperformance low-power intelligent microprocessor. With a variety of installation methods: wallmounted, desktop placement. Added built-in siren, up to 110dB. It connects all of your accessories to the APP, so you can stay in control of your home from anywhere.
1.
II. Set up the Security Devices 2.1 Security Panel Installation Diagram (1) Wall Mount F Security Panel×1 Wall Hanging Plate×1 Screws×2 1. Install the hanging 2. Align the hole on the plate on the wall with back of the panel with the screws. hanging plate and install it. Note: The screws must Note: For concealed wire be all nailed to the wall, installation, please remove and the hanging board the bracket and cable clip. must be parallel.
Appearance Design Front View Rear Main View Indicator: 4 / 16
Alarm Modes A. Security Panel Alarm Modes a. Away: The security panel is in a monitoring state, when the accessories are triggered, the security panel will alarm. b. Home: When the user is at home, in this mode, some areas can be monitored and alarms. c. Disarm: The security panel cancels the monitoring state, and only the SOS button or the accessories set to "Always" mode can trigger the alarm. B. a.
2.2 Entry Sensor Configure On the Security Panel: A. Go to Menu---Accessories---Enter User Code (Default: 1234). B. Press Sensor---“+” ----Entry, then set the Mode, Delay, and Advanced settings. C. Press “+ Pair”, then trigger the Entry sensor (Just separate the two parts). D. Paired successfully, rename the sensors on the APP. Installation The entry sensor should be installed on the door or window (see image). A.
Battery Replacement Door Sensor A Battery specification: CR2032×1 Door Sensor B Battery specification: CR2032×1 7 / 16
2.3 Motion Sensor Configure On the Security Panel: A. Go to Menu---Accessories---Enter User Code (Default: 1234). B. Press Sensor---“+” ----Motion, then set the Mode, Delay, and Advanced settings. C. Press “+ Pair”, then trigger the Motion sensor (Just wave your hands until the light is on). D. Paired successfully, rename the sensors on the APP. Installation A. The recommended installation height is 79”-87” (2.0~2.2m) above the ground. B.
Steps: 2.4 1) Screw the base to the wall 2) Hang the motion sensor on the rotating shaft Controller Configure On the Security Panel: A. Go to Menu---Accessories---Enter User Code (Default: 1234). B. Press Controller C. Press “ + ”, then trigger the controller (Press any key). D. Paired successfully, rename the controller on the APP.
2.5 Multifunction Button---Doorbell/SOS Button Configure----Doorbell Button On the Security Panel: A. Go to Menu---Accessories---Enter User Code (Default: 1234). B. Press Doorbell. C. Press “+”, then press the doorbell button. D. Paired successfully, rename the sensors on the APP. Configure----SOS Button On the Security Panel: A. Go to Menu---Accessories---Enter User Code (Default: 1234). B. Press Sensor---“+” ----Urgent, then set the Advanced setting. C.
III. Learn to Use the Security Panel 3.1 4.1.1 Main Interface System Status Icon Status 4.1.2 System is System is in alarm state armed disarmed Accessories Door/Window low battery opened Log Alarm Log: Arm Log: The system is View all alarm records, including Cause, Source, and Time. View all arm/disarm records, including Action, Source Device, and Time. Note: Support up to 160 Alarm records, and 80 Arm and disarm records.
3.2 Menu introduction Accessory A. Frame Diagram B. Sensor Entry: Manage all the Entry sensors. Motion: Manage all the Motion sensors. Urgent: Emergency detectors such as SOS buttons, gas detectors, and smoke detectors, please add them here. General: Other sensors or detectors, please add them here. Note: 1) The security system supports the accessories with 433MHz, ev1527.
Security (1) Frame Diagram (2) Delay: Customize the countdown time when Alarm or Arm. (3) Code: 1) User Code: Default user code is 1234. 2) System Code: Default system code is 9876. 3) Obfuscated Code: When entering the code, you can enter 5 to 8 digits of the obfuscated code, as long as it contains the correct 4 digits in succession, it can be recognized as the correct code.
IV. Troubleshooting and Maintenance Failure The Reason 1. Low battery 2. The metal sheet of the battery compartment is in Remote control poor contact or is corroded malfunction 3. The code is not paired with the panel 4. Does not match the wireless parameters of the panel 1. Low battery 2. The metal sheet of the battery compartment is in poor contact or is corroded Door sensor 3. The code is not paired with the panel failure 4. Does not match the wireless parameters of the panel 5.
No emergency call was made when the alarm was triggered 1. The panel is not armed 1. Arming the panel 2. No emergency phone number is set 3. Improper installation of accessories, too far away from the panel 2. Re-set according to the instructions 3. Adjust the position of accessories 4. Re-pair with the panel 4. Encoding does not match 1. The door opening code needs to be paired 1. Door sensor pairing error Entry opened 2.
VII. FCC declares This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.