Smart Security Kit H500 Instruction Manual 1
Contents 1. Description of Terms ........................................................................................................... 3 2. Introduction ........................................................................................................................... 6 3. Characteristics of Safety Panel .......................................................................................... 7 4. Introduction of Appearance and Panel............................................................
1. Description of Terms Host:The safety panel is the core of the whole house safety, hereinafter referred to as the host. Out Arm:The host enters the alarm state after the accessories are triggered when it is in a monitoring state. Stay Arm:It refers to the mode of arming the host when the user is in the internal protection area of the alarm system.
Siren alarm:The host sends the wireless code to control the wireless siren to give an alarm when the host alarms. Siren beep:The host sends a wireless code to control the wireless alarm to sound briefly for prompting when the host state is switched. Delay beep:The warning voice would be issued to evacuate the protection area as soon as possible to avoid false triggering or cancellation of the alarm when the host is in a delayed protection or delayed alarm state.
treatment such as gas, emergency key and smoke. (4) Disabled:Setting the detector in this mode means that it is discontinued and the host would not respond to the alarm request of the detector in this mode. (5) No alarm sound for 24 hours:This type of accessories would give an alarm when giving an alarm, but it would not make a sound. (6) All Arm is effective (without delay):The user can ignore the alarm delay setting when this type of accessories conform the alarm conditions.
2. Introduction Welcome to use the Smart Security kits. Your safety is the direction of our efforts. The host is embedded with a high-performance and low-power intelligent microprocessor, adopted the 4.3-inch IPS color screen. The user can use The Touch Buttons to control host operation.It has wireless function that can wireless connect the infrared, door sensor, smoke, gas, detector, emergency key, wireless remote and other accessories for matching.
3. Characteristics of Safety Panel Embedding the ARM9 chip. The main frequency is up to 600MHz. The performance is more powerful and the operation is more faster. (1) The 4.3-inch IPS color display screen has a wider visual angle and better visual experience. (2) Capacities touch screen is used and the user experience will be more comfortable. (3) New Sense UI interactive interface. (4) It built-in RTC clock chip.
4.
Indicator: Action Action Light steady Color Flashing Color Red Alarm mode Yellow/Green Change Delay Arm Yellow Arm mode Red/Green Change Delay Alarm Green Disarm mode Important (1) The host should be installed in the center area of each detector as much as possible to ensure the best wireless communication between the host and the detector.
5. Functions Introduction of Security Panel 5.1. Menu Introduction Deleting, view and modify detector alarm type Detector Accessories and mode for all detector. Remote Adding, view and delete all remote controllers. Doorbell Adding, view and delete all doorbell. Realize wireless alarm number matching Siren pair function.
Scope: off or on; Default: On Set whether the key sound effect is turned on or not Key beep Scope: off or on; Default: On Set the prompt volume of the host doorbell Doorbell Vol Scope: 0 ~ 10; 0 indicates that the doorbell is muted; Default: 8 Set the prompt volume of the host system System vol Scope: 0 ~ 10; 0 indicates that the system prompts mute; Default: 7 Set screen timeout Display Unit: seconds; Scope: 0 constant bright, 10 ~ 180; Default: 60 seconds There are 8 Language languages you 简体中文、
6. Installation and Usage of Accessories 6.1. Installation Diagram of Infrared Motion Detector Important: (1) The installation height from the ground is 2.0 ~ 2.2 meters. The detection distance is ≤ 7 m and the launching distance is ≤ 150 m (without obstacles). Please ask for TEST distance before installation, because the obstacle has an effect on the distance to sense.
6.2.2. Battery Replacement 6.3. Installation Diagram of Door Sensor The door sensor is installed on the movable door or window. First, wipe the corresponding position of the door, take out the wireless door sensor, and stick double-sided adhesive tape on the bottom.
Important (1) The emission distance of the door sensor is less than or equal to 100M (no obstacles). Please ask for TEST distance before installation. Because the obstacle has an effect on the distance to sense. (2) The door sensor (transmitter (large)) and the door sensor (magnet (small)) shall be installed separately, i.e. the transmitter shall be installed on a fixed door frame and the magnet shall be installed on the movable door.
6.4. Installation and Disassembling Diagram of Doorbell Characteristics: (1) A variety of simple installation methods: support foam glue and screw fixing. (2) No standby power consumption. (3) DC12V power supply is adopted, with higher transmission power and longer wireless distance. Installation step: 1.Firstly, the user need to hold the lower cover with your left hand, fasten the bottom of the upper cover with the bottom of the lower cover with your right hand.
2.
7. Specifications of The Smart Security Panel and Accessory 7.1. The Main Specifications of Smart Security Panels Input power: Input power: 5V 1.0A, Micro USB Working temperature: -10 ~ 55℃ Battery inside: 3.7 V 1000mAh lithium battery Relative humidity:<95% (no condensation) Operating power consumption:<1.5 W Product size:150*120*12mm Wireless parameters:433MHz frequency band, eV1527 coding 7.2.
7.4. The Specifications of Door Sensor Wireless parameter: 433MHz, support coding Input voltage: 23A 12V format eV1527 Support frequency band Quiescent current:≤2 uA Operating temperature: -10℃ ~ + 50℃ Alarm current:≤20 mA Relative humidity:<95% (no condensation) Product size: Transmitter (large) 65 * 24 mm magnet (small) 52 * 11. 4mm 7.5.
8. The Table Abnormal Fault Handling Failure Wireless Remote malfunction Door sensor failure The Reason The Solution 5. 1. The battery power is insufficient. 2. The shrapnel of the battery compartment. is in poor contact or rusted. model. 6. 2、Cleaning the rust and dirt of shrapnel. 7. 3、Re-pair with the host. 8. 4、Purchasing accessories of the same 9. type with technical parameters. 3. The format is not paired with the host. 4. Mismatch with host wireless parameters. 1.
2. Door and window switch signals cannot be used. 3. 3. Setting the type of alarm as door alarm and window alarm. Setting the type of alarm incorrectly.
9. The Declaration of Hazardous Substances Harmful substance Component Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) chromium biphenyls diphenylethers (Cr(VI)) (PBB) (PBDE) Metal parts O O O O O O Plastic parts O O O O O O 10. Warranty Rules (1) Please contact our after-sales service for any failure caused by the product itself during the warranty period.
Warranty Card Thank you very much for using our products. This card is a product warranty certificate. Please keep it properly. Thanks again.
Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.