BT06 Bluetooth audio receiver User’s manual 1. 2. 3. Before use…………………………………………………………1 About BT06………………………………………………………1 System requirements……………………………………………….1 Overview of BT06…………………………………………...……1 1. 2. 3. 4. 5. Getting started……………………………………………………2 Charging the receiver……………………………………………....2 Turning on/off the receiver………………………………………...2 Pairing with Bluetooth devices………………………………….…3 Music playback…………………………………………………….5 LED indicator……………………………………………………...
Welcome to use this Bluetooth stereo receiver BT06. Please read this user’s manual carefully before use. Before use 1. About BT06 BT06 is a stereo Bluetooth audio adapter. You can use a common audio device with 3.5mm audio in jack for playing back any stereo Bluetooth-enabled device’s music after plugging in BT06. The product comes with a built-in rechargeable battery; it can be used for about 12 hours after being charged fully. 2. System requirements Audio device with 3.
Getting started 1. Charging the receiver BT06 comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the receiver is low power, red LED flashes once and the receiver emits three tones every 20 seconds. Please recharge the battery of the receiver. Connect the charger to a standard power outlet and the charger plug to the charging jack of the receiver. Red LED is on while charging. It takes about 2.
3. Pairing with Bluetooth devices How to enter pairing mode Function Operation LED indicator LED flashes red and blue alternately Enter pairing mode Indication tone Two “DU” tones Ensure the receiver is turned off, otherwise turn it off first and then press and hold MFB button for 6~7 seconds until LED flashes red and blue alternately Remark: The pairing mode will last 2 minutes, the receiver BT006 will switch to standby mode automatically if no devices can be connected within 2 minutes.
Every time the receiver is turned on, it will automatically connect to last connected device. If you want to pair it with other devices, please turn off the Bluetooth function of last connected devices first and pair the receiver with the new device according to steps 1~6 mentioned above. When the reveiver is turned on and doesn’t connect to any devices, press MFB button twice, it will automatically connect to the last connected device.
5. LED indicator LED indicator LED flashes red and blue alternately Blue LED flashes once every 2 seconds Blue LED flashes twice every 5 seconds Red LED flashes once every 20 seconds Status of BT06 Pairing mode Standby mode and not connected Connected Low power 5 Care and maintenance Read the following recommendations before using the receiver. Following these you will be able to enjoy the product for many years.
FAQs 1. What to do when BT06 can’t be turned on? Please charge the BT06. 2. What to do when BT06 can’t pair and connect to a Bluetooth device? a) Make sure the Bluetooth device is placed within 5 meters; b) Ensure BT006 has entered pairing mode. 3. What to do when BT06 can’t be turned off? Please charge the BT006 for about 2 seconds.
Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications made to this device not expressly approved by Shenzhen Weiking Technology Co., Ltd. may void the FCC authorization to operate this device. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.