User’s Manual Bluetooth Clinical Electrical Thermometer Model DT1/DT2
1. The Basics This manual contains the instructions necessary to oper ate the product safely and in accordance with its functio n and intended use. Observance of this manual is a pr erequisite for proper product performance and correct o peration and ensures patient and operator safety.Profess ionals, non-professionals, and patients can operate medi cal device in accordance with the instructions. 1.
thermometer. Do not share the thermometer with more than one person without disinfection, or it may cause cross-infection. Do not try to sterilize by immersing the thermometer head in alcohol or hot water (water temperature exceeds 50°C). Do not use force to squeeze the product. If the appearance is damaged, stop using it immediately. Precision components are used in the construction of this device.
Adults are required to shaving the skin before measuring their temperature. Make sure that the skin that is in contact with the thermometer is flat and wrinkle-free. Do not use the device where flammable gases such as anesthetic gases are present. It may cause an explosion. Please note that the use of this product in high temperature or humidity may cause inaccurate temperature measurement results. The effective wireless transmission distance of this product in a barrier-free environment is 10 meters.
2. Introduction 2.1 Intended Use The product is used to measure body temperature in the home and in the medical sector. 2.2 Contraindications Those who are allergic to stainless steel or PC plastic should not use this product. 2.3 Symbols Symbol CE0197 Meaning Application part type BF Manufacturer In conformity with Directive 93/42/EEC European Representative Symbol for “ENVIRONMENT PROTECTION – Waste electrical products should not be disposed of with household waste.
2.4 About the product Product name: Bluetooth Clinical Electrical Thermometer Software release version：V1 Product model: Model and Configuration see the table below. No. Model 1 2 DT1 DT2 Temperat ure measure ment function √ √ Bluetooth transmissio n function √ × 1 4 2 3 1. On/Off button On/Off：long press it to achieve this function. When you want to take your temperature again, shortly press it to re-measure your temperature. 2.
It can measure the temperature. 2.
3. Using the thermometer 3.1 Charge the Battery Use the USB cable to charge the product. Connect the USB cable to a USB charger or to the PC. There will be a battery logo flash on the device when charging.When the battery is low,the display screen will display a low power prompt. Note: The device cannot be used during charging.When charging, you must use a class Ⅱ adapter conforming to IEC/EN 60601-1, and the output is DC 5V 1A. If it is not followed, there may be a risk of electric shock. 3.
3.3 Measurement Note: Before measuring temperature, please clean the temperature measuring head with or rubbing alcohol. Rinse it with cool water. The thermometer supports measuring temperature of multiple body parts. For the infants under 3 months old, it is recommended to measure rectal temperature. Please follow the below instructions. Measuring oral temperature 1. With your mouth open, put the temperature measuring head under your tongue. 2. Close your lips gently around the thermometer. 3.
3.4 After Measurement 1. When the buzzer emits a beep sound(Beep-short sound) , it indicates that the temperature measurement is finished. The display "°C/℉ " stops blinking, and the displayed temperature value is the result of the current body temperature. Note: When the temperature measured by the device is lower than 35 ℃ or 95 ℉ , the screen will display "LOW"with beep-long sound. When the temperature measured by the device is higher than 41 ℃ or 105.
4. Cleaning and Disinfecting Do not use corrosive detergent to clean the unit. Clean and disinfect the thermometer before and after each use. Cleaning Process 1. Wipe probe with a cloth dipped in a disinfectant solution such as 70% isopropyl (rubbing) alcohol or soap and water. 2.Rinse off disinfectant residue. Care and Storage • Do NOT drop or crush; this device is not shock proof. • Do NOT dismantle or modify device.
5. Trouble Shooting Problem Possible Cause Can not boot Very low battery The ambient tem perature exceeds 40℃ or below 5℃. The monitor cannot be connected to other devices Inaccurate measured value Other devices have Bluetooth turned off Other devices don’t support the Bluetooth 4.0 BLE The temperature measuring heads are placed in different positions, resulting in different readings. Thermometer moves while measuring temperature.
The device has not been placed for more than 30 minutes from the colder environment to the measuring environment. The device has not been placed for more than 30 minutes from the warmer environment to the measuring environment. The measurement temperature exceeds 43.9℃ or below 30℃. Measurements should be taken before they are left in the measuring environment for more than 30 minutes. Measurements should be taken before they are left in the measuring environment for more than 30 minutes.
7. Specifications Classifications EC Directive Degree protection against electrical shock Environmental Item Temperature Relative humidity (noncondensing) MDD, 93/42/EEC RED, 2014/53/EU ROHS 2.
Charge time 2～3 hours. Temperature measurement Measurement Direct mode method Measurement site Mouth,Axilla,Rectum REFERENCE Mouth,Axilla,Rectum BODY SITE Temperature Unit Celsius(℃）or Fahrenheit(℉） Temperature range 32.0 – 43.9℃（89.6-111.0℉） Less than 35.8℃, ±0.3℃.(Less than 96.4℉, ±0.5℉.) 35.8℃ to less than 37℃,±0.2℃.(96.4℉ to less than 98.0℉,±0.3℉.) 37.0℃ to 39.0℃, ±0.1℃.(98.0℉ to Measurement 102.0℉, ±0.2℉.) accuracy Greater than 39.0℃ to 41.0℃,±0.2℃.(Greater than 102.0℉ to 106.0℉,±00.3℉.
8. Electromagnetic Compatibility The device meets the requirements of EN 60601-1-2. Warnings and Cautionary Advices Using accessories other than those specified in this manual may result in increased electromagnetic emission or decreased electromagnetic immunity of the equipment. The device or its components should not be used adjacent to or stacked with other equipment.
Voltage Fluctuations / Flicker Emissions IEC 61000-3-3 Complies power supply network that supplies buildings used for domestic purposes.
Guidance and Declaration - Electromagnetic Immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment. Immunity test IEC60601 level test Compliance level Electromagnetic environment guidance - Electrostatic discharge (ESD) IEC 61000-4-2 ± 6 kV contact ± 8 kV air ± 6 kV contact ± 8 kV air Floors should be wood, concrete or ceramic tile.
Power frequency (50/60 HZ) magnetic field IEC 61000-4-8 UT) for 5 s <5 % UT (>95 % dip in UT) for 5 s battery. 3 A/m 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. Note: UT is the AC mains voltage prior to application of the test level. Guidance and Declaration - Electromagnetic Immunity The device is intended for use in the specified electromagnetic environment.
less than the compliance level in each frequency range b. Interference may occur in the vicinity of equipment marked with the following symbol: Note 1: At 80 MHz to 800 MHz, the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.
Recommended separation distances between portable and mobile RF communications equipment and the device The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
FCC Warnning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Shenzhen Viatom Technology Co., Ltd. 4E, Building 3, Tingwei industrial Park, No.6 Liufang Road,Block 67 Xin’an Street, Baoan District Shenzhen,518101 Guangdong China www.viatomtech.com info@viatomtech.
