制作工艺: 80g书写纸;骑马钉,黑白印刷 尺寸: 95*147mm 此页不印刷
Baby Sleep Monitor Contact us: service@getbabytone.com Website: www.getbabytone.
Contents NOTICE ................................................................................ 1 1 Tips for Safe Sleep ........................................................ 1 2 Warnings and Cautions.................................................. 1 3 Unpacking ..................................................................... 2 4 Using the device and App.............................................. 2 5 Maintenance ..................................................................
NOTICE This product is not a medical device. It is not intended for use as a medical device or to replace a medical device. It does not and is not intended to diagnose, cure, treat, alleviate or prevent any disease or health condition or investigate, replace or modify anatomy or any physiological process. This product is only intended to assist you in tracking your baby’s wellbeing and is not intended to replace you as a caregiver.
without consulting your doctor. In particular, do not start taking any new medication or change the type and/or dosage of any existing medication without prior approval. Use only cables, sensors and other accessories specified in this manual. Prolonged using may increase the risk of undesirable changes in skin characteristics, such as irritation, reddening, blistering or burns. Do not open the device cover without authorization. The cover should only be opened by a qualified service personnel.
Press the side button for 2 seconds. POWER OFF: 3 ways: Press the side button for 2 seconds. Unplug the sensor cable, it will power off automatically if not connected to phone for 2 minutes. Even with sensor cable connected, it will power off automatically if no working for 10 minutes. 4.4 Placement Guide before working To ensure that the measurement is performed normally, please follow the steps below to wear the device.
A. Place the foot wrap on the foot (either foot works), with the sensor part running on the outside edge of the foot. The device should be oriented to the baby’s leg. B. Put the foot wrap around the foot and attach the velcro securely with no gap between the foot wrap and the baby’s skin. The light emitter and the light detector should be opposite to each other on the two sides of the foot.
4.5 Start working After the placement, press the side button for 2 seconds to power on. There should be red light inside the soft wrap. After a few seconds, readings will be displayed on the screen. If the screen display “poor signal”, please check if the sensor has been positioned and secured properly. When the above symbol displays on device screen, it indicates the readings is unavailable right now. When at rest, there will be readings in a few seconds.
4.6 Stop working Unplug the sensor cable, the countdown on the screen will begin. During the countdown, if you plug the sensor cable again, the record will be resumed. Notice: If the working time is less than 2 minutes, there will be no data saved If the device power off during working, the data should have been saved. 4.7 Screen wake up / change display During measurement, the screen will go off automatically for saving power; you can press the side button to wake up the screen or change display. 4.
4.9 Add a new device For the initial use, you need to add a new device. 1) Turn on device, run App, select . 2) Follow the App instruction to add the new device. 4.10 App Offline Mode | Multiple Devices If you enter App Offline Mode, you can view history data, in App Settings->Select Device, you can select device if you have multiple devices. In this Mode, device is not connected so you cannot sync data or set device. 5 Maintenance 5.
6 Troubleshooting Problem No readings on screen Device does not turn on or no response The app cannot find the device Possible Cause Possible Solution the sensor is not positioned and secured properly check if the sensor has been positioned and secured properly Baby is moving frequently It will recover when at rest Battery may be low. Charge battery and try again. Device might be damaged. Please contact your local distributor. The Bluetooth of your phone is off.
7 Specifications Environmental Operating Storage Temperature 5 to 40°C -25 to 70°C Relative humidity (noncondensing) 10% to 95% 10% to 95% Barometric 700 to 1060hPa 700 to 1060hPa Degree of dust & water resistance IP22 Weight 31g (main unit with band and sensor) Size 49×27×14 mm (main unit) Battery 3.7Vdc, Rechargeable Lithium-polymer Charge time 2-3 hours Battery life 16 hours for typical use Wireless Bluetooth 4.
8 Symbols Symbol Description Manufacturer Date of manufacture SN Serial number Indicates a device that is not to be disposed of as unsorted municipal waste. Follow Instructions for Use. MRI unsafe. Presents hazards in all MR environments as device contains strongly ferromagnetic materials. IP22 Resistant to liquid ingress This product complies with the rules and regulations of the Federal Communication Commission.
FCC Statement FCC Warning: FCC ID: 2ADXK-1661 Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ViHealth Shenzhen Viatom Technology Co., Ltd 4E, Building 3, Tingwei Industrial Park, No.6 Liufang Road, Block 67, Xin'an Street, Baoan District, Shenzhen, 518101, Guangdong, China Product name: Baby sleep monitor PN: 255-05170-00 Version: A Model: S1 Date: May.