Shenzhen uvision Technology Co., Ltd. Room 410, building 3, liuxian culture park, no.
About this manual The products described in this manual are for sale and use in mainland China only. This manual is used as a guide. The photos, graphics, charts and illustrations provided in the manual, For the purpose of explanation and explanation only, there may be differences with the specific product, please refer to the actual product. Declaration of responsibility Within the scope of the law allow maximum, this manual describes products (including its hardware, software, firmware, etc.
roduct introduction Wireless screen transmitter can realize automatic wireless screen projection, mirror screen projection, bidirectional control and other intelligent office meeting functions in a variety of platforms.
I、 Use with meeting tablet 1. Scheme 1: use wireless projector Meeting flat end pairing Connect the wireless projector to the USB port of the conference panel and wait for the device to pair automatically. The indicator light will change from the flashing state to the long-bright state, which means the match is successful. After success, the main interface of the projection screen prompts that the pairing is successful, then pull out the wireless projector.
transmitter is looking for the receiver; LED indicates long and bright aperture: it indicates that the wireless screen transmitter is in the ready state and can transmit the screen at any time;At this time, press the wireless screen transmitter button to achieve the screen function. Step 3: end the projection Press the wireless projector button again to end the projection. 2. Plan 2: use with mobile devices a) Android devices Support Android system 2.
b) Apple devices Support Apple iPhone IOS 8.0 and above, Apple iPad IOS 8.0 and above Open the wireless hotspot of the conference tablet and record the wireless hotspot name and password Open Apple device WIFI and search WIFI hotspot ShareAP-*** (" ShareAP-*** "depends on the hotspot name of the actual device) Enter the account password of WIFI hotspot, the default password is 12345678 Select the screen image in the control center of the Apple device and begin the wireless projection.
the receiving box Plug one end of the HDMI connector into the display device (projector, monitor) and the other end into the HDMI connector in the receiving box FIG. 5 wiring diagram of receiving box and display equipment Step 2 boot the receiver box Long press the power on key of the receiving box for 3 seconds to start the machine. After starting the machine, the power lamp will show the blue color and the program interface will appear on the screen of the display device (projector, monitor). FIG.
The third step is to pair the receiving box with the display device Connect the wireless projector to the USB port at the back of the receiving box and wait for the device to pair automatically. The indicator light will change from the flashing state to the long-bright state, which means the pairing is successful. Figure 7 receiver box pairing After success, the main interface of the projection screen prompts that the pairing is successful, then pull out the wireless projector.
When the PC system is set to turn off automatic playback of mobile devices, the automatic installation of the driver function will not be realized.At this point, manually open "ShareMax" in the root directory of the wireless projector storage space to install and pair with the PC. The first time you use it, it takes about 1 minute to install the driver and about 20 seconds for subsequent use to start automatically and pair. If the system prompts for permission or antivirus software, please choose to agree.
Support Windows 7/8/10, IOS 8.0, android 2.3 or above Resolution 1080 p The frame rate of 25 ~ 30 FPS Transmission delay < 200 ms Touch return support 10 point touch return (Windows, Mac) Support mouse mode return (Windows, Mac) WIFI type 2.4g /5G dual-frequency WIFI, The wireless rate is > 400 Mbps Wireless transmission protocol IEEE 802.11a /g/n/ac Band 5.8 G Encryption AES Verify protocol wpa2-psk 2. Receiving box parameter Master RK3288 DDR 2 gb DDR3 8 gigabytes of storage Power DC5V, 2.
HDMI 1 USB 2 Headphone jack 1 Power interface 1 Rj45 1 The TF extension supports a maximum of 64 gb Infrared support HDMI output Supports 720P/1080P/2K/4K resolution Support ratio 4:3, 16:9 (special ratio can be manually matched) WIFI type 2.4g /5G dual-frequency WIFI, The wireless rate is >, 200 Mbps*2 Wireless transmission protocol IEEE 802.11a /g/n/ac WIFI working mode STA and AP work simultaneously Encryption AES Verify protocol wpa2-psk Audio/video Video decoding Support h. 263, h. 264, h.
Mouse support Laser touch support Operating temperature -20℃~70℃ Infrared touch support Capacitive touch support Part of the name Administrative measures for the limitation of harmful substances in electrical and electronic products to restrict substances or elements Lea d (Pb) Mer cury (Hg) Cad miu m (Cd) Ⅵ hexava lent chromi um Polybromi nated biphenyls (PBB) Polybrominat ed diphenyl ether (PBDE) 13
(Cr) Metal parts x Ο Ο Ο Ο Ο Plastic parts O Ο Ο Ο Ο Ο The glass parts x Ο Ο Ο Ο Ο Circuit board x Ο Ο Ο Ο Ο The attachment x Ο Ο Ο Ο Ο This form is prepared according to the provisions of SJ/T 11364-2014. Ο said the harmful substances in the parts of homogeneous material content are all in the limited requirements of GB/T 26572-2011.
The warranty service Dear users: Thank you for choosing this product. In order to fully enjoy the perfect after-sales service support, please read the instructions of this product warranty card carefully after purchase and keep it properly. 1. With this card to enjoy the warranty period of free warranty and warranty period of preferential services. 2. Free replacement period of 7 days from the date of purchase due to quality problems, and the warranty period of 2 years. 3.
20C