Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
Table of Content Chapter 1 Introduction...................................................................5 1.1 Introduction.........................................................................5 1.2 Product Features .................................................................6 1.3 Package Contents................................................................7 1.4 LED Indicator And Port Description...................................8 Chapter 2 Hardware Installation.................................
Chapter 6 Wireless Setting ..........................................................42 6.1 Basic Settings ......................................................... 42 6.2 Wireless Security Setting .......................................... 44 6.3 Advanced Settings ................................................... 48 6.4 WPS Settings .......................................................... 49 6.5 Wireless Access Control ........................................... 52 6.6 Connection Status ...............
11.6 WAN Ping ............................................................ 71 Chapter 12 Routing Setting .........................................................72 Chapter 13 System Tools.............................................................73 13.1 Time Settings ........................................................ 73 13.2 DDNS.................................................................. 74 13.3 Backup/Restore Settings ......................................... 75 14.
Chapter 1 Introduction 1.1 Introduction. Thank you for purchasing Tenda 3G 150Mbps Portable 3G Wireless Router. 3G150M is a high speed 150Mbps Wireless Router, which complies with the latest IEEE802.11n and IEEE802.11b/g standards and provides up to 150Mbps wireless receiving and transmitting rate with its wireless transmitting distance 3 times farther than G-products. It includes 3G Router, Wireless Router,WISP and Wireless AP in one.
Wireless Router Mode: Use this mode to form a wireless local network that has broadband access via an Ethernet cable. In addition to having the flexibility of connecting a mobile broadband USB modem to share the internet and files through the 3G150M, users retain a full range of previous generation networking options. A key feature of the 3G150M is “Mode” button – greatly convenient for working modes switching.
memorizing long passwords ¾ Provides one 10/100Mbps Auto-Negotiation Ethernet LAN/WAN port ¾ Supports xDSL/cable modem static, dynamic connections ¾ Supports remote/local web management ¾ Supports wireless roaming technology for highly efficient connections ¾ Supports SSID stealth mode and a MAC address access control(up to 30 entries) ¾ Provides a router system log ¾ Supports auto negotiation/manual mode 802.11b/802.11g/802.
¾ One common USB line（connect with the power adapter） ¾ One Y type USB line(connect with computer’s USB port for Power supply) If any of the listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately. 1.4 LED Indicator and Port Description Front Panel and LED Indicator Show 1.4.1 LED indicator description on front panel: (from L to R) ¾ 3G Router Always blue indicates the device is in 3G Router working mode.
¾ AP Always blue indicates the device is in wireless AP working mode. ¾ WISP Router Always blue indicates the device is in WISP Router working mode. ¾ Wireless Router Always blue indicates the device is in Wireless Router working mode. ¾ 3G Insert the 3G USB modem card. When the indicator turns blue, it indicates the device is well connected. Blinking indicates it is transmitting data packets. ¾ WPS/Reset Press the button for one second, the indicator will blink.
about 1 second, the WPS feature will be enabled and WPS indicator will be shown blinking. Press this button for 7 seconds, the settings configured in this device will be deleted and it will restore the settings to the default one. ¾ MODE Press this button to change working modes and the matching indicator will turn blue. 1.4.3 Rear Panel Show： Rear Panel：（From L to R） ¾ POWER The port is for USB line connection.
Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the box, please follow the steps below to connect the device. For better wireless performance, please put the device in the middle of wireless coverage area. Please use the included power adapter to power on the Router. (IMPORTANT: Use of a different power adapter could cause damage and void the warranty for this product.) 2.2 Network Application Plan 2.2.
2.2.2 Wireless AP Mode Connect a single Ethernet cable to the access point or let it pick up another wireless device's transmission, and make a wireless connection available to all in range.
2.2.3 WISP Mode This is mainly used in hotspot access. Not only your computer can connect to the Internet via a router in WISP mode, but other Wi-Fi devices (PDA, PSP, Wi-Fi phone) can access the Internet without running up bills. 2.2.4 Wireless Router Mode Use this mode to form a wireless local network that has broadband access via an Ethernet cable.
Chapter 3 How to Login to the Router The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation (Please refer to chapter2.), the following steps will assist you to set the network configurations for you computer. The default web page login is IP:192.168.0.1 3.1 How to Set the Wired Network Configurations 3.1.1 On your computer desktop right click “My Network Places” and select “Properties”.
3.1.2 Right click “Local Area Network Connection” and select “Properties”. 3.1.3 Select “Internet Protocol (TCP/IP)” and click “Properties”.
3.1.4 Select “Obtain an IP address automatically” or select “Use the following IP address (S)”. A. “Obtain an IP address automatically” as the following diagram: B. “Use the following IP address (S)” IP Address: 192.168.0.XXX: (XXX is a number from 2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 DNS Server: Certainly you need to input the DNS server address provided by your ISP. Otherwise, you can use the Router’s default gateway as the DNS proxy server. Click “OK” to save the configurations.
Tip: If you are not sure of the DNS server address, we recommend you to select “Obtain an IP address automatically (O)” and “Obtain a DNS server address automatically”. 3.2 How to Set the Wireless Network Connection If you choose the Wireless Router mode, you should make sure that you have a wireless network adapter. Then set the wireless connection as below. 3.2.1 On your computer desktop right click “My Network Places” and select “Properties”.
3.2.2 Right click “Wireless Network Connection” and select “Properties” then configure the IP address as 3.1.3 and 3.1.4. 3.2.3 Right click “Wireless Network Connection” and select “View Available Wireless Network”. The entire wireless signal will be shown in the interface. Please select “Tenda”. If you don’t find it, please click “Refresh Network List”. 3.2.4 Select “Tenda” and click “Connect” or double-click “Tenda” to enter into the Router’s interface. 3.
3.3.1 To access the Router’s Web-based interface, launch a web browser such as Internet Explorer and enter the Router’s default IP address, http://192.168.0.1. Press “Enter”. 3.3.2 Input the “admin” in both User Name and Password. Click “OK”. 3.3.3 If you enter the correct user name and password, the screen will be the next one.
Chapter 4 Modes Setup Wizard There are four working modes: 3G Router, Wireless AP, WISP, Wireless Router. This chapter will describe the basic settings of modes using Setup Wizard, 4.1 3G Router Mode 4.1.2 Login to the interface In “3G Router” mode, click “Setup Wizard” in the left column and then click “Next”. 4.1.3Configure the Connetcion Method First, select your 3G card type.
Second, select your ISP. Third, click “Next” to enter Wireless Basic Settings interface. Tip: If your ISP is not in the list, consult your ISP for detail parameters and manual input. 4.1.4 Wireless Basic Setting ¾ Network Mode：Select one mode from the following. The default is 11b/g/n mode. 11b mode： Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps. 11g mode： Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed of 54Mbps.
11b/g/n mode Allow 11b/g/n-compliant client device to connect with the AP with auto-negotiation speed. ¾ SSID：SSID (Service Set Identifier) is the unique name of the wireless network. ¾ Channel：Specify the effective channel (from 1 to 13\Auto) of the wireless network ¾ Broadcast (SSID): Select “Enable” to enable the device's SSID to be visible by wireless clients. The default is enabled. ¾ BSSID：Basic Service Set Identifier of wireless network. In IEEE802.
4.1.5 Wireless Security Setting It is suggested you choose WPA-personal for “Security Mode” and AES for “WPA Algorithms.” Click “Next” to save the configuration. More details please refer to the following chapter. 4.1.6 Click “Apply” to save the settings. The Router is rebooting now, please wait for a few minutes and DO NOT power off it.
4.2 Wireless AP Mode In “Wireless AP”, click “Setup Wizard” in the left column and then click “Next”. The setting methods please refer to 4.1.4 to 4.1.6. In this mode, the device is a converter that can convert the wireless and wired signals. You can connect a single Ethernet cable to the access point or let it pick up another wireless device's transmission, and make a wireless connection available to all in range.
4.3.2 In WISP settings interface, select the channel you want to use and then click “Scan” to scan the wireless signals. ¾ SSID：SSID (Service Set Identifier) is the unique name of the wireless network. ¾ MAC Address: The Router’s physical MAC address as seen on your local network is unchangeable. Input the MAC address of the AP you want to choose.
address is also named BSSID. (BSSID：Basic Service Set Identifier of wireless network. In IEEE802.11, BSSID is the MAC address of wireless access point. ¾ Channel：Specify the effective channel (from 1 to 13\Auto) of the wireless network. The channel you select must be correspondence with the AP provided by your ISP. ¾ Security Mode: The security mode you set should be the same as the AP. More details please refer to the Wireless Security Settings chapter.
4.4 Wireless Router Mode In the wireless router mode, you can use this device as the router directly connected to DSL modem, CABLE modem such broadband devices or home broadband cable directly First, login to the interface as chapter 3 described. 4.4.1 Select the “Setup Wizard” in the left column and then click “Next”. 4.4.2 Configure the “Aceess Methods” a. Dynimic IP(DHCP) The default access method is DHCP. If your ISP provides you the Dynamic IP, you can choose DHCP access way.
b. Static IP If your ISP provides you the Static IP, please select Static IP access way. You should input the IP address, Subnet Mask, Gateway, DNS sever and the secondary DNS sever provided by your ISP, then click “Next”. Other steps refer to 4.1.4 to 4.1.6. c. ADSL Virtual Dial-up (via PPPoE) This way is used when the Router is connected to the wireless modem or you want to amplify wireless signals and share the Internet with multiple computers.
Account and Password provided by your ISP. Note: If you choose this access way, the LAN/WAN port is only worked as the WAN port. The mode will take effect once you set it; you need to login to the Router’s WEB interface to configure the device (Details refer to 3.2). After configuration, you should adjust the connection properties to obtain an IP address automatically in Internet protocol (details refer to Appendix One). d. PPTP and L2TP Configure L2TP and PPTP. Take PPTP as an example.
PPTP Server: Enter the IP address or PPTP Server domain name User Name: Enter your PPTP user name Password: Input your PPTP password Address Mode: Static mode and Dynamic mode. Select Dynamic mode to get IP automatically. If you select Static mode, you need to manually set the IP address, Subnet Mask, Default Gateway.
Chapter 5 Advanced Settings 5.1 LAN Setting This section will describe how to configure the TCP/IP parameters. 5.1.1 In 3G Router mode, WISP mode, Wireless Router mode, please configures the LAN port parameters as the below diagram (Note: In Wireless mode, you can only configure the device until you using the wireless access way.). ¾ MAC Address: The device’s physical MAC address as seen on your local network is unchangeable. ¾ IP Address: The Router’s LAN IP addresses (not your PC’s IP address). 192.
it for the Web-based Utility login next time. 5.1.2 LAN Settings in Wireless AP Mode ¾ MAC Address: The device’s physical MAC address as seen on your local network is unchangeable. ¾ IP Mode: There are two modes, Static IP and Dynamic IP. If you select Static IP, you need to input the parameters provided by your ISP. If you choose Dynamic IP, you should adjust the connection properties to obtain an IP address and DNS sever automatically in Internet protocol.
measurement of the network size. 255.255.255.0 is the default value. ¾ Default Gateway: Input the Gateway provided by your ISP. If you are not sure, please consult your ISP. ¾ Primary DNS Sever: Input the primary DNS sever provided by your ISP. ¾ Secondary DNS Sever: you can input it or empty it. The parameters are also provided by your ISP ¾ Host Name: The device’s wins name which you can use it to visit the device.
5.2 WAN Settings 5.2.1 3G WAN Network Setting ¾ 3G Card Type: Select you 3G USB Modem card type from the list. ¾ ISP: Select your ISP. ¾ Apply: Click “Apply” button after configuration. ¾ Cancel: Click “Cancel” to the former settings when you make a mistake. ¾ Click “System Status” to scan the information.
can share the internet. Internet Connection Option: There are four Connection Options: Connect Automatically, Connect Manually, Connect on Demand, Connect on Fixed Time. Please select according to your needs. ¾ Connect Automatically: Connect automatically to the Internet after rebooting the system or connection failure. ¾ Connect Manually: Connect to the Internet by users manually. ¾ Connect on Demand: Re-establish your connection to the Internet after the specific time (Max Idle Time).
Note: it is suggested you choosing Connect on Demand without running up bills, because it can disconnect the internet automatically when there is no data transmitting or the computer closed. If you access the internet, it will dial up automatically which is very convenient. 5.2.2 WAN Settings in WISP Mode and Wireless Router Mode Depending on your access ways of WAN port, there are three ways of configuration. a. Dynamic IP ¾ MTU: Maximum Transmission Unit.
b. ADSL Virtual Dial-up(via PPPoE) ¾ Connection Method: It shows the current connection method. ¾ User Name: Input the user name provided by your ISP. ¾ Password: Enter the password provided by your ISP. ¾ MTU: Maximum Transmission Unit. It is the size of largest datagram that can be sent over a network. The default value is 1492. Do NOT modify it unless necessary.
¾ Service Name: It is defined as a set of characteristics that are applied to a PPPoE connection. Enter it if provided. Do NOT modify it unless necessary. ¾ AC Name: Enter it if provided. Do NOT modify it unless necessary. ¾ Connect Automatically: Connect automatically to the Internet after rebooting the system or connection failure. ¾ Connect Manually: Connect to the Internet by users manually.
c. Static IP If your connection mode is static IP, you can modify the following addressing information. ¾ IP Address: Here enter the WAN IP address provided by your ISP. If you are not clear, consult you ISP please. ¾ Subnet Mask: ¾ Gateway: Enter the WAN Gateway here. ¾ Primary DNS Server: Enter the Primary DNS server Enter the WAN Subnet Mask here. provided by your ISP. ¾ Secondary DNS Server: Enter the secondary DNS. ¾ MTU: Maximum Transmission Unit.
or enabled, you can have a try to change the MTU value as 1450, 1400, etc. 5.3 MAC Address Clone This page is for the Router’s MAC address to WAN.(Only in Wireless Router mode) Some ISPs require end-user's MAC address to access their network. This feature copies the MAC address of your network device to the Router. ¾ MAC Address: The MAC address to be registered with your Internet service provider. ¾ Clone MAC Address: Register your PC's MAC address.
provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them. ¾ DNS: Click the checkbox to enable the DNS server. The Router’s DHCP sever will answer the client’s requests and distribute DNS address. ¾ Primary DNS Address: Enter the necessary address provided by your ISP. ¾ Secondary DNS Address: Enter the second address if your ISP provides, which is optional.
Chapter 6 Wireless Setting 6.1 Basic Settings ¾ Enable Wireless: Check to enable the Router’s wireless features; uncheck to disable it. ¾ Network Mode：Select one mode from the following. The default is 11b/g/n mode. 11b mode： Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps.
11g mode： Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed of 54Mbps. 11b/g mode: Allow the 11b/g-compliant client device to connect with the AP with auto-negotiation speed, and 11n wireless client to connect the device with 11g speed. 11b/g/n mode：Allow 11b/g/n-compliant client device to connect with the AP with auto-negotiation speed. ¾ SSID：SSID (Service Set Identifier) is the unique name of the wireless network.
¾ Channel Bandwidth ： Select the channel bandwidth to improve the wireless performance. When the network has 11b/g and 11n clients, you can select the 40M; when it is an 11n network, select 20/40M to improve its throughput. 6.2 Wireless Security Setting It is used to configure the AP network’s security setting. Here presents the common six (ten in all) encryption methods, including WPA-personal, WPA2-personal, Mixed WAP/WAP2-Personla, Mixed WEP, Open, Shared.
¾ WPA Algorithms：Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. ¾ Pass Phrase: Enter the encrypted characters with 8-63 ASCII characters. ¾ Key Renewal Interval：Set the key’s renewal period. 6.2.2 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) or WPA (Wi-Fi Protected Access). Besides TKIP encryption, new AES encryption mode is provided.
¾ WPA Algorithms：Provides TKIP [Temporal Key Integrity Protocol], AES [Advanced Encryption Standard] or TKIP&AES mixed mode. ¾ Pass Phrase：Enter the encrypted characters with 8-63 ASCII characters. ¾ Key Renewal Interval：Set the key’s renewal period. 6.2.3 Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of digital keys (64 bits or 128 bits in length).
¾ Select SSID：Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. ¾ Security Mode ： From the drop-down menu select the corresponding security encryption modes. ¾ WEP Key：Set the WEP key with the format of ASCII and Hex. ¾ Key Explanation: You can enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters.
6.3 Advanced Settings This section is to configure the advanced wireless setting of the Router, including the BG Protection Mode, Basic Data Rates, Fragmentation Threshold, RTS Threshold, and WMM etc. ¾ BG protection Mode: Auto by default. It is for 11b/g wireless client to connect 11n wireless network smoothly in a complicated wireless area. ¾ Basic Data Rates: For different requirement, you can select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.-11Mbps…).
the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting. The default size is 2346 bytes. It is recommended not to modify this value. ¾ RTS Threshold: RTS stands for “Request to Send”. This parameter controls what size data packet the frequency protocol issues to RTS packet. The default value of the attribute is 2346. It is recommended not to modify this value in SOHO environment. ¾ TX Power: Set the output power of wireless radio.
encryption method and secret keys by manual. In the “WLAN settings” menu, click “WPS settings” to enter the next screen. ¾ WPS settings：To enable or disable WPS function. The default is “disable”. ¾ WPS mode ： Provide two ways: PBC (Push-Button Configuration) and PIN code. ¾ PBC：Select the PBC or press the WPS button on the back panel of the device for about one second (Press the button for about one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled.
the WPS indicator will be off, which means the WPS connection is completed. If more clients are added, repeat the above steps. At present, the WPS supports up to 32 clients access.) ¾ PIN：If this option is enabled, you need to enter a wireless client’s PIN code in the field and keep the same code in the WPS client. ¾ WPS Summary ： Show the current state of Wi-Fi protected setting, including authorized mode, encryption type, default key and other information.
generally AES/TKIP. ¾ WPS key ： The effective key generated by AP automatically. ¾ AP PIN（KEY）：The PIN code used by default. ¾ Reset OOB： When this button is pressed, the WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client’s requests and the set the security mode as WPA mode. 6.
prevent the MAC addresses in the list from accessing the wireless network; “Allow” to allow the MAC address in the list to access the wireless network. ¾ MAC Address Management：Input the MAC address to implement the filter policy. Click “Add” to finish the MAC add operation. ¾ MAC Address list：Show the added MAC addresses. You can add or delete them. 6.6 Connection Status This page shows wireless client’s connection status, including MAC address, Channel bandwidth, etc.
Chapter 7 DHCP Server DHCP server is for the 3G Router, signal amplification and wireless Router mode. 7.1 DHCP Settings DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”.
For example： If the lease time is an hour, then DHCP server will reclaim the IP address each hour. 7.2 DHCP List and Binding DHCP client can display computers’ IP address; MAC address, host name and other information which are assigned by the DHCP sever. You can manually enter the IP and MAC address; it would be converted to static allocation. According to the computer's MAC address, DHCP will assign the appropriate IP address.
¾ IP Address: Enter the IP address which needs to be bound. ¾ MAC Address: Enter the MAC address of the computer you want to assign the above IP address. Click “Add” to add the entry in the list. ¾ Hostname: The name of the computer which is added a new IP address. ¾ Lease Time: The left time length of the corresponding IP address lease.
Chapter 8 Virtual Server Virtual Server feature is only for wireless signal amplification mode and the wireless Router mode. 8.1 Port Range Forwarding This section deals with the port range forwarding mainly. The Port Range Forwarding allows you to set up a range of public services such as web servers, ftp, e-mail and other specialized Internet applications to an assigned IP address on your LAN.
to set the applications. ¾ Protocol: Select the protocol (TCP/UDP/Both) for the application. ¾ Enable: Click to check it for corresponding operation. ¾ Delete: Click to empty the parameters. ¾ Well-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to add to the configured one above. ¾ Add: Add the selected well-known port to the policy ID. For example: The server at the IP address of 192.168.0.
¾ DMZ Host IP Address: The IP address of the computer you want to expose. ¾ Enable: Click the checkbox to enable the DMZ host. For example: Set the computer at the IP address of 192.168.0.100 in LAN as a DMZ Host to intercommunicate with another host on the Internet. IMPORTANT: When the DMZ host is enabled, the firewall settings of the DMZ host will not function. 8.3 UPNP Settings It supports latest Universal Plug and Play.
¾ Enable UPnP: Click the checkbox to enable the UPnP.
Chapter 9 Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration. ¾ Enable Traffic Control: To enable or disable the internal IP bandwidth control. The default is disabled. ¾ Interface: To limit the uploading and downloading ¾ Service: To select the controlled service type, such as HTTP bandwidth in WAN port. service.
or IP segment. ¾ UP/Down: To specify the traffic heading way for the selected IP addresses: uploading or downloading. ¾ Bandwidth Range: To specify the uploading/downloading Min. /Max. Traffic speed (KB/s), which can not exceed the WAN speed. ¾ Apply: To enable the current editing rule. If not, the rule will be disabled. ¾ Add: After edit the rule, click the “add to list” button to add the current rule to rule list. ¾ Apply: Click “Save” to activate the current rule.
Chapter 10 3G WAN Traffic and Connection Timer 10.1 3G WAN Traffic In 3G WAN mode, 3G WAN traffic function is supported. Click "3G WAN traffic" you can check the router's Internet traffic, transmission rate, transmission data volume and traffic for nearly two months, so that you can know how much the traffic that the 3G modem card accesses the Internet without running up bills. Notice: this function is only for 3G WAN. In 3G Router mode, 3G WAN traffic is used to calculate the traffics of WAN port.
Note:The result of 3G WAN Traffic and Connection Timer are only for reference. This device can only calculate the status that the 3G modem card plugs into the device. The actual statistics is subject to the ISP.
Chapter 11 Security Settings The security settings are for the 3G Router, the Wireless signal amplification mode and the Wireless Router mode. The security settings of wireless access point (AP) mode please refer to Chapter 6. 11.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filters function. ¾ Client Filter: Check to enable client filter.
¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access policy. ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ IP Start/End: Enter the starting/ending IP address. ¾ Port: Enter the port range based over the protocol for access policy. ¾ Type: Select one protocol (TCP/UDP/Both) from the drop-down menu. ¾ Times: Select the time range of client filter.
certain websites at fixed time. ¾ URL Filter: Check to enable URL filter. ¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access policy. ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ Start/End IP: Enter the starting/ending IP address. ¾ URL: Specify the text strings or keywords needed to be filtered.
¾ Days: Select the day(s) to run the access policy. ¾ Apply: Select Apply to enable the settings. For example: If you want the computer at the IP address of 192.168.0.123 to access the Internet from 9：00 to 18：00 everyday and only can search the WEB pages contain the strings such as sina, sohu, and yahoo, you need to set the packet filtering list as the above diagram. (Notice: different strings need to be aparted by a comma.) 11.
¾ MAC Address Filter: Check to enable MAC address filter. ¾ Access Policy: Select one number from the drop-down menu. ¾ Enable: Check to enable the access policy. ¾ Filter Mode: Click one radio button to enable or disable to access the Internet. ¾ Policy Name: Enter a name for the access policy selected. ¾ MAC Address: Enter the MAC address you want to run the access policy. ¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy.
¾ Prevent Network Attack: Check to enable it for attack prevention. 11. 5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”. ¾ Enable: Check to enable remote web management. ¾ Port: The management port open to outside access. The default value is 80. ¾ WAN IP Address: Specify the range of the WAN IP address for remote management.
Note：1. If you want to login the device’s Web-based interface via port 8080, you need use the format of WAN IP address: port (for example http：//220.135.211.56:8080) to implement remote login. 2. If your WAN IP address starts and ends with 0.0.0.0, it means all hosts in WAN can implement remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33, 218.88.93.34 and 218.88.93.35 can access the Router.
Chapter 12 Routing Setting Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed.
Chapter 13 System Tools 13.1 Time Settings This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet. ¾ Time Zone: Select your time zone from the drop-down menu. ¾ Customized time: Enter the time you customize. Note： When the Router is powered off, the time setting will be lost.
13.2 DDNS The DDNS (Dynamic Domain Name System) is supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up. ¾ Main Features: Owing to ISP most times provides dynamic IP address, DDNS is used to capture the changeable IP address and match the fixed domain.
¾ Service Provider: Select one from the drop-down menu and press “Sign up” for registration. ¾ User Name: Enter the user name the same as the registration name. ¾ Password: Enter the password you set. ¾ Domain Name: Enter the domain name which is optional. For example： In the local host 192.168.0.10 establish a Web server, and register in 3322.org as follows: User name tenda Password 123456 Domain Name tenda.vicp.
¾ Backup Setting： Click “Backup” button to back up the Router’s settings and select the path for save. Click “Save” to save the configuration files.
¾ Restore Setting： Click “Browse” button to select the backup files. Click “Restore” button to restore previous settings. 14.4 Restore to Factory Default Setting This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary.
¾ Restore: Click this button to restore to default settings. ¾ Factory Default Settings: User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.0 NOTE: After restoring to default settings, please restart the device, then the default settings can go into effect. 13.5 Upgrade Firmware The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn.
¾ Browse: click this button to select the upgrade file. ¾ Upgrade: click this button to start the upgrading process. After the upgrade is completed, the Router will reboot automatically. Note: Do not disconnect the device during the upgrade. 13.6 Reboot the Router Rebooting the Router makes the settings configured go into effect or to set the Router again if setting failure happens. Reboot the router: Click this button to reboot the device. 13.
¾ User Name: Enter a new user name for the device. ¾ Old Password: Enter the old password. ¾ New Password: Enter a new password. ¾ Re-enter to Confirm: Re-enter to confirm the new password. Note: It is highly recommended to change the password to secure your network and the Router. 13.8 System Log The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically.
¾ Refresh: Click this button to update the log. ¾ Clear: Click this button to clear the current shown log. 13.9 Logout After you have finished the settings completely, in logout page click “Yes” to logout the web management page.
Appendix Ⅰ: How to “Obtain an IP Automatically” If you enable DHCP (default), you can get the IP address, Gateway, DNS automatically to access the internet. Please set you device as below. 1. On your computer desktop right click “My Network Places” and select “Properties”. 2. Right click “Local Area Network Connection” and select “Properties”. If you use wireless connection, please click “Wireless Network Connection”.
3. Select “Internet Protocol (TCP/IP)” and click “Properties”.
4. Select “Obtain an IP address automatically” 5. Select “Status” within “Local Area Connection " – click "support "dialog box, you can see whether you have got the IP.
Appendix Ⅱ: How to set the network adapter after device encrypted When the device is encrypted, you need to enter password to connect to the wireless device to access the internet. Set up a wireless network adapter as follows: 1. On your computer desktop right click “My Network Places” and select “Properties”. 2. Right click “Wireless Network Connection” and select “View Available Wireless Network”. The entire wireless signal will be shown in the interface. Please select “Tenda”.
3. Select “Tenda” and click “Connect” or double-click “Tenda”, input the “Network key” and “Confirm network key” to connect the Router 4. “Connected” will be shown in the interface as the following diagram.
Appendix Ⅲ Glossary 3G 3G, the 3rd Generation, refers to the third digital communication technology. It can manage multi-media such as image, audio, and video streams etc. and provide different communication services such as web browse, telephone session, and electronic business etc. CDMA2000 CDMA2000, also called CDMA Multi-Carrier, is one of the current three 3G standards in the world which was put forward by an American company. The system derives from narrow frequency CDMAOne digital standard.
the world. Channel An instance of medium use for the purpose of passing protocol data units (PDUs) that may be used simultaneously, in the same volume of space, with other instances of medium use(on other channels) by other instances of the same physical layer (PHY),with an acceptably low frame error ratio(FER) due to mutual interference. SSID Service Set Identifier .An SSID is the network name shared by all devices in a wireless network.
encryption. There are 2 methods for entering the KEY; one is to enter a 16-bit HEX digit. Using this method, users must enter a 10-digit number (for 64-bit) or 26-digit number (for 128-bit) in the KEY field. Users must select the same key number for all devices. The other method is to enter a text and let the computer generate the WEP key for you. However, since each product use different method for key generation, it might not work for different products. Therefore, it is NOT recommended using.
Appendix Ⅳ: Troubleshooting In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.cn, and we will reply you in the earliest time. 1. Enter the IP address but can not visit the WEB management interface. What can I do? Please make sure the cable is well connected and the corresponding indicator is light.
default settings. 3. The computer connected with the Router shows IP address conflict. What can I do? Check if there are other DHCP servers in the LAN. If there have, disable them. The default IP address of the Router is 192.168.0.1 and please maker sure the address is not occupied by other devices. If there are two computers with the same IP addresses, please modify one. 4.
IP? In Setup Wizard of the Web utility interface, select “Dynamic IP” connection type and click “Save” to activate it. As some ISPs bind the user computer’s MAC address, you need to clone the Router’s WAN MAC address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it. 7.
host: TCP, UDP, ICMP . Step 7: click “Apply” to activate the settings. The following table has listed the well-known application and service port: Server Protocol Service Port WEB Server TCP 80 FTP Server TCP 21 Telnet TCP 23 NetMeeting TCP 1503、1720 MSN Messenger TCP/UDP Voice:1863、6901(TCP) PPTP VPN TCP 1723 File Send:6891-6900(TCP) Voice:1863、5190(UDP) Iphone5.0 TCP 22555 SMTP TCP 25 POP3 TCP 110 8. Why can’t I use wireless WAN function to access the Internet? a.
b. Please make sure that the needed parameters such as SSID, MAC address etc. are correct. It is recommended to use Auto Scan to finish the settings in the setup process. c. Please make sure that IP address range obtained at WAN port are different as the one obtained at LAN port. If they are at the same range, you can modify the LAN IP address to solve the problem. d. Please do not detach any antenna of the wireless Router when you are using the Router.
AppendixⅤ: Complied 3G Modem Card List Brand Model Brand Model Tenda 3G189C D-LINK DWM_162U5 HUAWEI EC169 D-LINK DWM_162 HUAWEI EC169 New DCWL 390 HUAWEI EC1260 China Ruijie EV2000 HUAWEI EC1260 New GXZG GX100C HUAWEI EC1260 India MACAO CTM H21 HUAWEI EC1261 WEWINS U602D HUAWEI ET128 ChangHe 868 HUAWEI E1750 HiNet E220 HUAWEI EC226 TURKCELL E176G HUAWEI E1630 TMobile Vodafone E220 HUAWEI E176G Vodafone K3520 HUAWEI E176 Chile Cricket UM185C HUAWEI E18
HUAWEI MD-@ HSUPA Sprint USB 598 HUAWEI E160E Sprint U150 HUAWEI E1550 Sprint U760 HUAWEI EZ220 3G UK Verizon USB760 HUAWEI BASE e.
ZTE AC2746 DeUnite ZTE AC8710 DeUnite DU458 ZTE MF637U JinXunChi EV169 ZTE MU350 TIMESPOWER WM2080A-110 ZTE MF622 T-Linking T-Linking ZTE MF627 CM810EV ZTE AC2726 MC727 AC2726 LKT 828 ZTE DU456 Reliance ZTE AC8700 BSNL ZTE AC8710 TATA ChangHong CH600 Datang AirCard 901 Modem LC625 Remark: 1. The 3G modem cards in the above list are compatible with this 3G Router. Please confirm that the 3G modem card you purchased is in the compatibility list.
modem cards. If you find that our Router can not support your 3G modem card, please visit our official website www.tenda.cn to download new firmware. 3. Huawei EC226 、 EC122 、 E176G, Viton E1916 ， ZTE MU351 and GXZG LKT828 are added in V0.5. 4. You are recommended to use the extended USB line to connect your 3G modem card with the 3G Router to reach a better effect. 5. New functions supported in this version: a.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This Device complies with RSS-210 of the IC Rules, Operation is subject to the following two conditions: (1). This device may not cause interference and (2). This device must accept any interference received,, including interference that may cause undesired operation.
