TeamGee Electric Skateboard TEAMGEE Operation Manual of Electric Skateboard Please read this Manual before using the skateboard. Website:WWW.teamgee.
TeamGee Electric Skateboard Safety Warning This Manual is designed for TeamGee H5-H20 series products only. We provide important safety warnings and precautions in this Manual. Please keep them in mind, ensure safety in use and be sure to read this Manual before use. 1. Skateboard has potential risks like other sports, and it might cause injury. When riding the skateboard, the user might tumble due to loss of balance and get injured or even die. 2.
TeamGee Electric Skateboard Disclaimer 1. When the motor is moving, do not touch it with any part of your body to avoid getting abrasions and other accidental injuries. 2. Do not dismantle the equipment without permission; otherwise, if the skateboard is damaged due to inappropriate dismantling, it will not be covered within the scope of warranty. 3.
TeamGee Electric Skateboard Contents 1. Introduction to the Skateboard....................................................................................5 Briefly introduce the composition of each part on electric skateboard. 2. Product display……………………………………………………………………..5-7 3. Remote control…………………………………………………………………..8-12 Use of the remote control to understand the user interface, specific operations and the use of pairing mode and data mode. 4. Remote control technical parameters.......................
TeamGee Electric Skateboard Model 5 H5
TeamGee Electric Skateboard Model H6 Model H9 6
TeamGee Electric Skateboard Model H20mini 7
TeamGee Electric Skateboard Model H20/H20T 8
TeamGee Electric Skateboard Remote control (Use of the remote control to understand the user interface, specific operations, and the use of pairing mode and data mode.
TeamGee Electric Skateboard Instruction for Remote Control Code • Under normal circumstances, the code program of each board and the supporting remote control has completed when the product leaves the factory, so consumers do not need to code again. However, when you accidentally lose the remote control or buy a new remote control or the remote control is damaged and repaired, the code must be completed before use. • Steps:1 1 .First turn on the power of the board.
TeamGee Electric Skateboard 1、Remote control technical parameters Specification Remote for Skateboard TG002 Model Battery Voltage/Capacity 3.7V/300MAH Charging Port Micro USB Charging Time 1H Communication Mode 2.
TeamGee Electric Skateboard Performance Max. load 90kg Target users 14-50 years old Gear L: 10-12 km/h Gear M:12-20 km/h Speed Gear H:20-25 km/h Gear H+: 25-35km/h Battery Parameters Driving mileage ≥10-15km Battery type Polymer battery Standard voltage 36v 10S1P 3.5Ah Battery capacity 126Wh Motor type Double-drive brushless hub motor 90*54mm SHR83A PU rubber coating Rated output power 350W*2 Torque 6Nm Max.
TeamGee Electric Skateboard Product Parameter Doulbe-drive 36V H9 Skateboard Model Board dimension (subject 980MM*230MM*15MM to the real product) Wheel base 785MM Total weight 6.
TeamGee Electric Skateboard 10S1P 3.5Ah Battery capacity 126Wh Motor type Double-drive brushless hub motor 90*54mm SHR83A PU rubber coating Rated output power 480W*2 Torque 10Nm Max. instantaneous power 1200W Rated voltage 36v Type High-elasticity PU wheel (sky blue, black ) Specification 90*54mm SHR83A rubber coating Bearing HCH 608RS ABEC-7 Input voltage AC100-240v 50/60Hz Charger Output voltage and current DC42V 1.5A Parameters Charging time 2-3hours Mfr.
TeamGee Electric Skateboard Weight 55g Applicable Electronic Speed Controller TEAMGEE-Skateboard-H5/H6/H9/H20/H20T/H20mini 2、Technical Parameters of Skateboard (Subject to the Purchased Product) Product Parameter Model Board dimension (subject to the real product) Doulbe-drive 36V H20 H20mini Skateboard H20:930MM*243MM*11.5MM;H20mini: 800MM*230MM*11MM Wheel base H20:765MM;H20mini:545MM Total weight H20:8.55kg; H20mini:7.
TeamGee Electric Skateboard B3 B4 9.0Ah Battery≥45-48km Driving mileage Battery Parameters 18650 Battery type Li-ion Battery 36v Standard voltage 18650 10S3P Battery capacity 9.0Ah/324Wh Motor type Double-drive brushless hub motor 90*54mm SHR83A PU rubber coating Rated output power 540W*2 Torque 10Nm Max.
TeamGee Electric Skateboard Product Parameter Doulbe-drive 36V H20T Skateboard Model Board dimension (subject 930MM*243MM*11.5MM to the real product) Wheel base 765MM Total weight 9.65kg Ground clearance of board Product Specification 133MM surface Climbing Angle 10%-25% Board material and Board material:8-layer Canadian maple board + 1-layer glass fiber board, board thickness thickness: 11.
TeamGee Electric Skateboard 18650 10S3P Battery capacity Motor Parameters PU wheel 9.0Ah/324Wh Motor type Double-drive brushless hub motor 103*54mm polyurethane rubber tire Rated output power 540W*2 Torque 10Nm Max. instantaneous power 1200W Rated voltage 36v Type Polyurethane rubber tire 103*54mm Specification polyurethane rubber tire Bearing HCH 608RS ABEC-7 Input voltage AC100-240v 50/60Hz Charger Output voltage and current DC42V 1.7A Parameters Charging time 2-4hours Mfr.
TeamGee Electric Skateboard Packaging List 1 TeamGee electric skateboard is a finished product and you can use it normally without needing to assemble. 2 The above accessories are all provided at delivery of H5-H20 and the final delivery accessories shall be subject to the actual objects provided by the seller.
TeamGee Electric Skateboard The bushing is an indispensable and important part of skateboard, and users can adjust its tightness according to their weight and riding habit, so as to better experience the fun of sliding. As shown in the figure: adjust nut tightness, and the skateboard’s steering angle, sliding stability and steering sensitivity can be changed. (The nuts should not be too loose, to prevent the nuts from falling off and causing danger during the riding).
TeamGee Electric Skateboard 2 Turn left, make the center of your body weight backward slightly, press your weight toward the heel, and you will find that you start to turn left. 3 Turn right, make the center of your body weight forward slightly, press your weight toward the tiptoe, and you will find that you start to slide forward right. 6.
TeamGee Electric Skateboard the original charger; otherwise, it might cause fire and even explosions in serious cases. 6. Do not replace the original charging plug, which might be dangerous. 7. It is forbidden to charge in the process of use. Such operation will cause serious consequence, such as fire or explosions. 8. Please keep the electric skateboard far away from the liquids, inflammables, explosives and other hazardous substances during the charging.
TeamGee Electric Skateboard control, connect the other end to a 5V power supply, and when the remote control has been fully charged, open remote control switch machine key, the power indicator of the remote control is full of electricity, which means the charging is completed and the charger can be unplugged. Skills for Riding the Skateboard We have always put the user safety in the first place, and this is why we specially prepare this chapter to remind you to pay attention to the dangerous roads.
TeamGee Electric Skateboard Junction of sidewalk and lane Usually there are steps and even gap less than 3cm at the junction of roads. When passing through or getting ready to pass through it, maintain a certain speed and plan the riding route to make it form an angle of 45° with the junction. Small pits on the roads Be careful to avoid these “traps”. If the pit is big, the wheel might get stuck. If your wheel gets stuck in the pit during riding, it will lead to very serious consequence and injury.
TeamGee Electric Skateboard Battery: Forbid plugging conductive objective into the charging interface; otherwise, the internal electronic devices in the skateboard might be short circuited and damaged, and it might even be dangerous. Please use the electric skateboard at 10-30℃ as much as possible; otherwise, it will accelerate the aging of battery at high or low temperature, accelerate the attenuation of battery capacity, shorten the battery life, and reduce the driving millage.
TeamGee Electric Skateboard reduce the noise in driving process. Please try to store the Skateboard in a dry place between ambient temperature, in extremely humid environments, the interior of the Skateboard may suffer condensation or even water accumulation, which may damage the battery rapidly.
TeamGee Electric Skateboard When disposing of Skateboard or batteries, they must be recycled according to the regulations and standards of each region. Product Warranty Regulation The purchase invoice will be taken as the warranty voucher, and the purchase date will be the starting date of warranty. If you have no effective warranty voucher, the warranty period will be six months from the production date of product.
TeamGee Electric Skateboard be covered within the warranty. The bridge that unsolders and fractures naturally can be replaced, if the bridge Bridge 6 months appearance is damaged due to human collision or unauthorized refitting, the bridge will not be replaced. Scope and Contents not within “Three Guarantees” No. 1 Scope and Contents not Within “Three Guarantees” The fault which is caused due to the user’s failure to use, maintain and adjust according to this “Operation Manual”.
TeamGee Electric Skateboard Warranty Card Information I: Model Repair Date Machine Code Fault Phenomenon Analysis of Causes Signature of Analyst SN Information II: Model Repair Date Machine Code Fault Phenomenon Analysis of Causes Signature of Analyst SN On-line Service Website: www.teamgee.com; Market@teamgee.
TeamGee Electric Skateboard FCC Requirement : changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.