Connection Diagram

ManualsBrandsShenzhen Sunricher Technology ManualsElectronicsLED Controllers

Table Of Contents

4 in 1 Universal ZigBee LED Controller

ZG.01029.04737

Input

Voltage

Remarks

Output

Current

12-24VDC

Constant voltage

48-96W/CH

4A/CH

Output

Power

Function introduction

Important: Read All Instructions Prior to Installation

Product Data

Size(LxWxH)

145x46.5x16mm

• DO NOT install with power applied to device.

• DO NOT expose the device to moisture.

Safety & Warnings

Operation

1.Do wiring according to connection diagram correctly, please power off and power on the device once

a device mode is selected so that the selected mode can be activated.

2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible

systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee

system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

4. TouchLink to a Zigbee Remote

Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.

2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.

3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.

4) After TouchLink, the device can be controlled by the linked remotes.

Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will

fail. Please refer to the part "Factory Reset Manually".

Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as

instructed by the controller.

Step 4: Connected light will blink 5

times and then stay solid on, then the

device will appear in your controller's

menu and can be controlled through

controller or hub interface.

Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink

commissioning (lasts for 180S) immediately under any circumstances, once time out, repeat this step.

Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee

network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,

repeat the step.

Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly),

network pairing mode lasts 15S (enters into touchlink mode after 15S), once timeout, repeat this step.

Step 4: There shall be indication on

the remote for successful link and

connected light will flash twice.

< 10cm

Zigbee

Remote

Step 2: Bring the remote or touch panel within 10cm of the lighting device.

Step 3: Set the remote or touch panel into Touchlink commissioning,

please refer to corresponding remote or touch panel manual to learn how.

12-24VDC Power input

Common Anode Output(+)

CH1:R/R/WW/1 output(-)

CH2:G/G/CW/2 output(-)

2) Under RGB+CCT mode, RGB channels and tunable white channels are controlled separately, they can not

be turned on and controlled at the same time.

Program Key: short press to switch on/off the device,

press and hold down to increase/decrease light intensity

• 4 in 1 universal Zigbee LED controller based on latest ZigBee 3.0 protocol

• 4 different device modes DIM, CCT, RGBW and RGB+CCT in 1 controller, and selectable by dial switch

• Enables to control ON/OFF, light intensity, color temperature, RGB color of connected LED lights

• Can directly pair to a compatible ZigBee remote via Touchlink

• Supports self-forming zigbee network without coordinator

• Supports find and bind mode to bind a ZigBee remote

• Supports zigbee green power and can bind max. 20 zigbee green power remotes

• Compatible with universal Zigbee gateway or hub products

• Compatible with universal Zigbee remotes

• Waterproof grade: IP20

CH3:B/B/WW/3 output(-)

CH4:WW/W/CW/4 output(-)

CH5:CW/NC/NC/5 output(-)

Ambient

Temperature

-20℃ ~ +50℃

Prog.

ZigBee LED Controller

Input Voltage DC 12-24V

Output Current 4A/CH

Max Power 48-96W/CH

1 2

DC INPUT

LED OUTPUT

DIM

CCT

RGBW

RGB+CCT

1- R- R-

2- G- G-

3- B- B-

WW-

W-

CW-

NCNC

Ta:-20℃-+50℃

Dial switch for device mode

selection, DIM, CCT, RGBW

and RGB+CCT 4 modes are available,

factory default is RGB+CCT mode

1 2

NC = No Connection

1) Under RGBW mode, W channel can only be turned on through color temperature control command (RGBW

will be identified as RGB+CCT by zigbee). Color temperature control will mix RGB channels as 1 channel white

and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be

controlled together with RGB channels.

LED indicator, stays solid on when power on the controller, turns

off after added to a zigbee hub, indicates (same status as connected

load) when program the controller (network pairing, touchlink, factory reset)

Max. Casing

Temperature

75℃

AC Power

50/60Hz

V+

V-

OUTPUT

INPUT

12V/24V

CV PSU

RGB LED Strip

V+ V+

R- R-

G- G-

B- B-

CCT LED Strip

V+ V+

WW- WW-

CW- CW-

Prog.

ZigBee LE D Co nt roller

Input Vo lta ge D C 12- 24 V

Outpu t Cur re nt 4A /C H

Max Pow er 48 -9 6W/ CH

1 2

DC INPU T

LED OUT PUT

DIM

CCT

RGBW

RGB+C CT

1- R- R-

2- G- G -

3- B- B-

WW-

W-

CW-

NCNC

Ta:-20℃-+ 50℃

1 2

Max. 20A input

AC Power

50/60Hz

V+

V-

OUTPUT

INPUT

12V/24V

CV PSU

RGB LED Strip

V+ V+

R- R-

G- G-

B- B-

CCT LED Strip

V+ V+

WW- WW-

CW- CW-

Prog.

ZigBee LE D Co nt roller

Input Vo lta ge D C 12- 24 V

Outpu t Cur re nt 4A /C H

Max Pow er 48 -9 6W/ CH

1 2

DC INPU T

LED OUT PUT

DIM

CCT

RGBW

RGB+C CT

1- R- R-

2- G- G -

3- B- B-

WW-

W-

CW-

NCNC

Ta:-20℃-+ 50℃

1 2

Max. 20A input

Summary of content (4 pages)

PAGE 1
4 in 1 Universal ZigBee LED Controller ZG.01029.04737 Operation 1.Do wiring according to connection diagram correctly, please power off and power on the device once a device mode is selected so that the selected mode can be activated. 2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible Important: Read All Instructions Prior to Installation systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
PAGE 2
8. Find and Bind Mode 5. Removed from a Zigbee Network through Coordinator or Hub Interface Step 1: Short press “Prog.” button 3 times (Or re-power on the device (initiator node) 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the step. V- INPUT V+ indicate successful reset. OUTPUT From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed.
PAGE 3
Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the step. Wiring Diagram 1) RGB+CCT Mode OUTPUT V- INPUT V+ 12V/24V CV PSU V- L INPUT V+ OUTPUT 11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required) 12V/24V CV PSU L N AC Power 50/60Hz G N AC Power 50/60Hz G Max. 20A input Max.
PAGE 4
warning: FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.