Connection Diagram

ManualsBrandsShenzhen Sunricher Technology ManualsElectronicsLED Controllers

Table Of Contents

LED Controllers

09.ZG3FW.04282

1/R-

LED OUTPUT

2/G-

3/B-

4/W-

Function introduction

Important: Read All Instructions Prior to Installation

12-36VDC Input

Common Anode output (+)

• DO NOT install with power applied to device.

• DO NOT expose the device to moisture.

Product Data

Safety & Warnings

Input Voltage

Output Type

Output Current

12-36VDC

Constant voltage240-720W

4CH, 5A/CH

Output Power

12-36VDC

Constant current

16.8-50.4W

4CH, 0.35A/CH

12-36VDC

Constant current

33.6-100.8W

4CH, 0.7A/CH

No.

Dimension (LxWxH)

170x53.4x28mm

CH 1 (R) output (-)

CH 2 (G) output (-)

CH 3 (B) output (-)

CH 4 (W) output (-)

ZigBee RGBW Receiver

• ZigBee RGBW LED light device based on latest ZigBee 3.0 protocol

• Enables to control ON/OFF, light intensity and RGB color of connected RGBW LED lights

• W channel can only be controlled through color temperature control command

• Color temperature control will mix RGB channels as 1 channel white and then make color tuning with the

4th channel white

• ZigBee end device that supports Touchlink commissioning

• Supports find and bind mode to bind a ZigBee remote

• Compatible with universal ZigBee gateway products

• Waterproof grade: IP20

• Supports self-forming zigbee network without coordinator

• Supports zigbee green power and can bind max. 20 zigbee green power remotes

Program Key: short press to switch on/off load, press and hold down to increase/decrease light intensity

Prog .

Operation

1.Do wiring according to connection diagram correctly.

2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible

systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee

system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

4. TouchLink to a Zigbee Remote

< 10cm

Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.

2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.

3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.

4) After TouchLink, the device can be controlled by the linked remotes.

V+

V-

OUTPUT

INPUT

AC Power

50/60Hz

12V/24V/36V

CV PSU

V+ V+

R- R-

G- G-

B- B-

W- W-

1/R-

LED

2/G-

3/B-

4/W-

ZigBee RGBW Lighting Device

Prog.

Zigbee

Remote

V+

V-

OUTPUT

INPUT

AC Power

50/60Hz

12V/24V/36V

CV PSU

1/R-

LED

2/G-

3/B-

4/W-

ZigBee RGBW Lighting Device

Prog.

V+ V+

R- R-

G- G-

B- B-

W- W-

Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will

fail. Please refer to the part "Factory Reset Manually".

Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as

instructed by the controller.

Step 3: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15

seconds timeout, repeat the operation.

Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink

commissioning immediately, 180S timeout, repeat the operation.

Method 2: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee

network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,

repeat the operation.

Step 2: Bring the remote or touch panel within 10cm of the lighting device.

Step 3: Set the remote or touch panel into Touchlink commissioning,

please refer to corresponding remote or touch panel manual to learn how.

Step 4: Connected light will blink 5 times

and then stay solid on, then the device

will appear in your controller's menu and

can be controlled through controller or

hub interface.

Step 4: There shall be

indication on the

remote for successful

link and connected

light will flash twice.

5. Removed from a Zigbee Network through Coordinator or Hub Interface

From your ZigBee controller or hub interface, choose to delete or reset the

lighting device as instructed. The connected light blinks 3 times to indicate

successful reset.

Note: W channel can only be turned on through color temperature control command since Zigbee only has

tunable white control. Color temperature control will mix RGB channels as 1 channel white and then make color

tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together

with RGB channels.

SR-ZG9101FA-RGBW

Summary of content (3 pages)

PAGE 1
LED Controllers SR-ZG9101FA-RGBW 09.ZG3FW.04282 3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network) Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part "Factory Reset Manually". Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
PAGE 2
9. Learning to a Zigbee Green Power Remote Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to start Learning mode (connected light flashes twice), 180 seconds timeout, repeat the operation. the “Prog.” key is not accessible. OUTPUT 12V/24V/36V CV PSU V- N V+ G AC Power 50/60Hz INPUT G L INPUT L N OUTPUT 6.
PAGE 3
Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals. Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals. Note: 1) Each added device can link and be controlled by max. 30 added remotes. FCC Warning Statement 2) Each added remote can link and control max. 30 added devices. 12.