User's Manual

ManualsBrandsShenzhen Sunricher Technology ManualsElectronicsRF sender

Table Of Contents

RF wireless LED remote controller

Eight zones/areas

Touch button RGB+W controller

Receivers work with WIFI-RF converter to be controlled by smart phone

Model:SR-2818 with SR-1009Fxx

Parameter

Wiring diagram

Product Size

Brief introduction of buttons

Product introduction

SR-2818 RGBW remote controller is full touch remote controller which has 8 different zones. It can get Red/ Green/ Blue/

White color directly. The remote controller can save up to 8 colors or 8 modes into corresponding buttons (1-8 buttons)

for each zone. You can choose any color through color wheel. There is a USB port to charge internal battery.

Chargeable by USB

SR-1009FA 12-36VDC

Constant voltage

4x(60-180)W

4x5A

SR-1009EA 12-36VDC

Constant voltage

4x(96-288)W4x8A

Remote

Part No.

Operation Voltage

DIMENSIONS

ø/h (mm)

Operation

Frequency

SR-2818 3.7VDC

59x115x12

916.67MHz

Receiver

SR-1009FA3 12-36VDC

Constant current

4x(4.2-12.6)W

4x350mA

SR-1009FA7 12-36VDC

Constant current

4x(8.4-25.2)W4x700mA

Remarks

Lithium battery,

USB charging capability

1)Receiver Connection Diagram for Single Unit

2) Connection Diagram for Multiple UnitsReceiver

Power Supply

12-36VDC

110V-230VAC

whi te

SR-1009FA

LED CONTROLLER

1234

Lea rning K ey

whi te

SR-1009FA

LED CONTROLLER

1234

Lea rning K ey

whi te

SR-1009FA

LED CONTROLLER

1234

Lea rning K ey

Power Supply

12-36VDC

110V-230VAC

whi te

SR-1009FA

LED CONTROLLER

1234

Lea rning K ey

USB port

OFF

Bottom

55 66

77 88

11 22

33 44

Indicator

ON/OFF button

R/G/B/W button

Color wheel

Play & Pause button

Save color button

Return previous status button

Speed down & speed up button

Brightness button

Zone button

Indicator will be on while remote is charging.

Indicator will be off while it’s full power.

Note:

One receiver can work with 1-8pcs SR-2818

One SR-2818 control multiple receivers

The power supply chosen must be 20% higher than the

actual load

58.8

12.0

115.4

Part No.

Input Voltage

Remarks

Output Current

Output Power

Summary of content (3 pages)

PAGE 1
RF wireless LED remote controller Brief introduction of buttons Model:SR-2818 with SR-1009Fxx Bottom Indicator Color wheel ON/OFF button Play & Pause button USB port Save color button Return previous status button Eight zones/areas Touch button RGB+W controller Chargeable by USB Receivers work with WIFI-RF converter to be controlled by smart phone ON R/G/B/W button Brightness button Speed down & speed up button Zone button 5 OFF 1 2 3 4 5 6 7 8 Indicator will be on while remote is char
PAGE 2
b. How to save mode into different position per zone? Operation Learning (matching) a. Do wiring according to connection diagram b. Wake up the remote control by touching ON/OFF button. c. Press learning button on receiver. d. Touch any zone button on remote control. e. Then touch color wheel. f. Connected LED light will blink to confirm zone designation. g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
PAGE 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.