Users Manual Part 2

ManualsBrandsShenZhen SolidRF Communications ManualsElectronicsSignal Booster

Step4:ConnecttheSystem

Connect six antennas on the booster

Connect



six



antennas



the



booster

2. Connectthebooster tothe“Input”

portofsplitterbycable

Connecttheinsideantennaand

Pluginthepoweradaptorandconnectit

tothenearestpoweroutlet(surge

protectorrecommended).

Summary of content (9 pages)

PAGE 1
Step4: Connect the System 1 1. Connect six antennas on the booster 2. Connect the booster to the “Input” port of splitter by cable . Connect the inside antenna and Plug in the power adaptor and connect it to the nearest power outlet (surge protector recommended).
PAGE 2
Step5: Evaluate the Effects • Now that all of the components of the booster are in place, and the booster is powered on, it’s time to check the performance. If everything checks out, return to steps 2 and 3 to finalize installation. Here’s what you should look for: 1.) Run a signal strength/speed check. Test the signal strength with the booster off, then re‐test the signal in the same location after you plug‐in the power supply. You should have a stronger signal.
PAGE 3
Quick Trouble shooting Correct functioning: • Power Light should be solid green • The lights on the front panel indicate the condition of the booster. Every time the booster is p powered on,, all of the lights g will be green g in color for several seconds then off. This means the booster has passed the self check and is in good condition..
PAGE 4
Trouble Shooting: No Signal Improvement Step 4. Double check the location of outdoor and indoor units. units Make sure that the Minimum Separation Requirements have been met. Make sure that the outside antenna is not pointed towards the inside antenna. ≥3 feet ≥2 feet Minimum Required Separation Distance Between Indoor and Outdoor Unit： Horizontal Distance = 3 feet ((1 meter)) Vertical Distance = 2 feet (0.6 meter) (As far as possible) Step 5. Check incoming signal level at outdoor unit p position.
PAGE 5
Technical Specification LTE Cellular PCS (band 12/17) (band 13) ( band5) (band2/25) AWS (band 4) Uplink 698‐716 776‐787 824‐849 1850‐1915 1710‐1755 Downlink 728‐746 746‐757 869‐894 1930‐1995 2110‐2155 Frequency (MHz) Noise figure <5dB In‐band Flatness <8dB Weight 0.7Kg EIRP ≤1W Gain adjustment Impedance 20dB 50 ohm Operating temperature ‐5°~60° Current ≦1.
PAGE 6
20
PAGE 7
PAGE 8
Install the indoor antenna according to the minimum service distance of the antenna model below. Inside server antenna model ANT010901、ANT010701、ANT050701 Minimum separation distances D (m) 0.55 ANT060302、ANT040301、ANT080301、 ANT080302、ANT060301、SR-21300100 ANT070101、ANT060303 0.
PAGE 9
Antenna Kitting Information Gain/Loss Component Prod No. 1850‐1995MHz Manufacturer 698‐746 746‐787 824‐ D Description i ti MH MHz MH MHz 894MH 894MHz 1710‐ Outside Antenna ANT‐LF‐W1.5 1.5dBi 1.5dBi 1.5dBi \ \ Shenzhen Dachi Communications Co., Ltd. Outside Antenna ANT‐HF‐W1.5 \ \ \ 1.5dBi 1.5dBi Shenzhen Dachi Communications Co., Ltd. Inside Cable RG6SS 45Feet 2.2dB 2.3dB 2.5 dB 3.8 dB 3.3 dB\4.2dB Suirongcable Inside Cable SRG58‐30SS 4.5dB 4.5dB 4.9dB 7.6dB 7.2dB\8dB