What bands and wireless providers are served with this booster? Frequency Bands: LTE-707(Band12, 17)/LTE-781(Band13)/Cellular850 (Band5)/PCS-1900(Band2, 25)/AWS2100 (Band4). This equipment is a multiband signal amplifier which supports: Cellular 850 MHz, PCS 1900 MHz, AWS and 700 MHz for both AT&T and Verizon-4G networks as well as the Sprint 4G G-Block of 1900 MHz. SolidRF SR25502001 Delivers up to 50 dB of gain and supports CDMA, GSM, EVDO, LTE, HSPA+ and WCDMA technologies. How does it work? 1.
1. Location of the nearest cell tower – cell towers are situated to provide broad coverage; however, there are many areas in which signal strength may be reduced by topographic features or by local government restrictions on the height or placement of the towers themselves. Rural areas generally have fewer cell towers than urban regions. 2. Natural and man-made obstructions – signal strength can also be negatively affected by trees, hills, buildings, weather, and other obstructions.
Booster function Figure 1 OUTSIDE:to connect with outside cable, outside antenna. INSIDE: to connect with inside cable, inside antennas. Band lights: it shows the status of indicated band. Flicker means the booster fail on the band. Power light: It indicated whether the power is turn on. Signal booster joint types:SMA \ FME \ N
Notifications Do NOT plug in the power supply until outside antenna and inside antenna are connected to the amplifier. For wireless amplifier, do NOT attempt to connect the amplifier directly to mobile devices, this can cause serious damage to both of amplifier and mobile devices. For the purpose of vehicle use, do NOT use any type of glass-mount antenna. Outside antenna and inside antenna must be shielded from each other to prevent oscillation.
① : SR25502001 signal booster ② :Outside antenna ③ :Inside antenna ④ :Power adapter Location for outside antenna: Recommend Satisfactory Prohibited Outside antenna and inside antenna distance of not less than 5 feet.
Warnings and Recommendations Warning: This consumer booster is for Consumer use only. Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC regulations. Please contact FCC for details: details: 11-888888-CALLCALL-FCC. Warning: Outside antenna orientation orientation must be back side of inside antenna is to prevent the indoor antenna receiving the signal emitted by outside antenna. Otherwise it will cause selfself-oscillation of booster.
Antenna Kitting Information Prod No. Gain/Loss LTELTE-707 LTELTE-781 800MHz 1900MHz 1700MHz\ 1700MHz\ 2100MHz Outside Outside SRSR-30200100 2dBi 2dBi 2dBi 2dBi 2dBi SRSR-10200220 1.5dBi 1.5dBi 1.5dBi 1.5dBi 1.5dBi 1.5dBi 2dBi 2dBi Outdoor SRG58SRG58-15FN 15FN 2.35dB 2.35dB 2.4dB 2.4dB 2.56dB 2.56dB 3.9 3.9dB 3.7 3.7dB\ dB\4.
Description of network protection features: The SolidRF SR25502001 including safeguards to protect the cellular network from interference. Each Signal Booster is individually tested and factory set to ensure FCC compliance. 1. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. 2. The Signal Booster will amplify, but ONLY incoming and outgoing signals in order to increase coverage of authorized frequency bands. 3.
This is a CONSUMER device you MUST REGISTER THIS DEVICE with your wireless provider and BEFURE USE , have your provider’s consent .Most wireless provider consent to the use of signal boosters .Some provider may not consent to the use of this device on their network .If you are unsure ,contact your provider. You MUST operate this device with approved antenna and cables as specified by the manufacturer .Antennas MUST be installed at least 20cm (8inches) from any person.
user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.