Min I(Smart) User Manual Table of Contents 1. Introduction..................................................................................................2 2. Product Description .......................................................................................2 3. Indications for Use .........................................................................................2 4. Package Contents............................................................................................2 5.
Min I(Smart) User Manual 1. Introduction The Mini I(Smart I) Electric Oral Anesthesia Injector is a professional and painless local anesthesia injection device used for the oral cavity. Mini I(Smart I)Electric Oral Anesthesia Injector can play the role of automatic injection of anesthetics under the circumstances of block conduction anesthesia, local infiltration anesthesia and periodontal membrane local anesthesia in stomatology department.
Min I(Smart) User Manual • One charging cable • O-ring, 10 pieces. Set the o-ring in the front part of plunger. When suctioned back, the o-ring will produces a negative pressure on the anesthetic tube. • Disposable sleeve, 50 pie 5. Features and Benefits 1. Save on anesthetic and lower costs, with no pipeline or other consumables. 2. Simple operation, with one finger touching the controls of the pen-like handpiece. There is no foot switch. 3. Low noise with music. 4.
Min I(Smart) User Manual 7. Operating Procedure 7.1 Product indication and key function Serial number Name Function description 1 Music settings key After long press to enter the setting state, click to adjust the music sound 2 Injection mode setting key After the long press to enter the set state, click to switch to speed mode 3 Charge Indicating Lamp It is used to indicate the charging state.
Min I(Smart) User Manual 7.2 OLED screen description Serial number Name Screen description Displays the current injection mode status. There are three injection modes: 1 Injection mode 1. Periodontal membrane pattern 2. Fast mode 3.
Min I(Smart) User Manual Displays the current infusion status.There are two status displays Injection of state 6 1. Forward injection state 2. Suck back state 7 Injection pressure status Display current injection pressure 8 Injection pressure value Display the current injection pressure value 7.3 Specific operation method Install Boost Pipe and needle: Remove the protective cap from the front of the needle, taking care to protect yourself.
Min I(Smart) User Manual Velocity in different modes Mode Flow rate and flow rate accuracy at 1.8ml injection volume PDL 0.42mL/min,deviation±10% Slow mode (S) 1.02mL/min,deviation±10% 1.62mL/min,deviation±10% Fast mode(H) 3 Enter ready state: Click the Injection mode setting key to change the state of the lock to make it ready.
Min I(Smart) User Manual 9. Attention 1.The Mini I(Smart I) Electric Oral Anesthesia Injector is only intended for local anesthesia in Dentistry. It provides a constant speed pressure boost. The selection of anesthetic and needle shall be purchased according to doctors’ clinical requirements. Any results caused by misuse of anesthetic and needle have nothing to do with this product. 2. To keep the handpiece clean, we recommend using a disposable protective sleeve.
Min I(Smart) User Manual 10. FCC Caution Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: 1.
Min I(Smart) User Manual Symbol for "REFER TO INSTRUCTION MANUAL" Product must be collected separately BFType Equipment Caution Keep dry Fragile, handle with care Symbol for "CONFORMITE EUROPPENE MARK" Temperature limit Federal Communications Commission 13. Prevention of Cross-Contamination To help prevent cross-contamination between patients, place a new protective barrier sheath on the device for each new patient.
Min I(Smart) User Manual 16. Magnetic compatibility information WARNING: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
Min I(Smart) User Manual Guidance and manufacturer's declaration – electromagnetic immunity – for all EQUIPMENT and SYSTEMS Guidance and manufacturer´s declaration – electromagnetic emission The Mini I(Smart I) Electric Oral Anesthesia Injector is intended for use in the electromagnetic environment specified below. The customer or the user of Mini I(Smart I) I Electric Oral Anesthesia Injector should assure that it is used in such an environment.
Min I(Smart) User Manual IEC 61000-4-2 Electrostatic transient / burst IEC 61000-4-4 Surge IEC 61000-4-5 ± 15 kV air ± 2 kV, ± 4 kV, ± 8 kV, synthetic material, the relative humidity ± 15 kV air should be at least 30 %. ± 2 kV for power supply lines Mains power quality should be that of a ± 1 kV for input/output typical commercial or hospital N/A environment. lines ± 1 kV differential mode Mains power quality should be that of a typical commercial or hospital N/A environment.
Min I(Smart) User Manual Guidance and manufacturer´s declaration – electromagnetic immunity – for EQUIPMENT and SYSTEM Guidance and manufacturer´s declaration – electromagnetic immunity The Mini I(Smart I) Electric Oral Anesthesia Injector is intended for use in the electromagnetic environment specified below. The customer or the user of the Mini I(Smart I) Electric Oral Anesthesia Injector should assure that it is used in such an environment.
Min I(Smart) User Manual NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic is affected by absorption and reflection from structures, objects and people. a The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6,765 MHz to 6,795 MHz; 13,553 MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz.
Min I(Smart) User Manual Recommended separation distances between portable and mobile RF communications equipment and the EQUIPMENT or SYSTEM for EQUIPMENT and SYSTEMS Recommended separation distances between portable and mobile RF communications equipment and the Mini I(Smart I) Electric Oral Anesthesia Injector The Mini I(Smart I) Electric Oral Anesthesia Injector is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.